RIDGID Official Table Saw Manual: Repair Parts and Parts List

Page 59

Repair Parts

Parts List for RIDGID 10 Inch Table Saw

Model No. TS24001

RIDGID parts are available on-line at www.ridgidparts.com

Figure 1

Always Order by Part Number - not by Key Number

Key	Part No.	Description		Key	Part No.	Description
No.	Part No.	Description		No.	Part No.	Description
No.				No.


1	126317	* Bolt Carriage 1/4-20 x 1		36	827874	Nut Wing Nylon 1/2-13
2	827518	Mount Rail Extension		37	808380-17	* Screw Pan Hd #10 x 3/4
3	827545	Table Extension				Plastite
4	73352	* Nut Hex Flange 1/4-20		38	805550-5	Washer 7/32 x 5/8 x 1/16
5	827478	Clip Fence		39	830405	Cord w/Plug
6	159572-146	* Screw Hex Wash Hd Ty T		40	830406	Wrap Cord
		10-32 x 7/8		41	274622	Screw Hex Hd Ty T
7	830397	Scale Rip				1/4-20 x 1
8	809813-1	Screw Pan Rec 6-32 x 1/2		42	821521	Screw Hex Hd Shoulder .312
9	827872	Spring Rip Scale		43	827463	Bolt T 1/4-20
10	104879	Screw Lock Set 10-32x3/16		44	827482	Coupling 1/4-20
11	827533	Slider Rail		45	827515	Link Locking Front
12	830345	Cap Rail Front Right		46	827523	Pivot Linkage
13	448013	* Screw Pan Hd Ty Ab N8x1/2		47	827515-1	Link Locking Rear
14	830378	Rail Front		48	830377	Bearing Rail Lock
15	830396	Cap Rail Front Left		49	827514	Lever Table Lock
16	827497	Panel Front		50	274205	Nut Lock 1/4-20
17	827870	Scale Bevel		51	805552	* Washer 17/64 x5/8 x 1/16
18	808380-2	* Screw Pan Hd #8 x 3/8		52	813051-5	* Screw Pan Hd 1/4-20 x 2-3/4
19	829971-8	Base w/Labels		53	830376	Table Main
20	9420474	* Screw Hex Wash Hd Ty T		54	827645	Cap Rear Rail Left
		10-32 x 1/2		55	827525	Rail Rear
21	826395	Bezel Switch		56	827470	Cap Rear Rail Right
22	AC1000	† Key Switch		57	509492	Insert Asm
23	808380-18	Screw Pan Hd #6 x 3/4		58	809374	Screw Flat Hd 10-32 x 1
		Plastite		59	826390	Insert Ind-I-Cut
24	808275-4	* Screw Pan Hd 8-32 x 3/8		60	805297-12	Screw Soc Flat Hd
25	827493	Foot Base				5/16-18 x 1
26	808380-5	* Screw Pan Hd #8 Plastite		61	138671	Screw Set 5/16-18 x 5/8
27	830399	Plate Switch Box		62	826347	Switch Locking
28	805475	* Nut Hex 8-32		63	829971-7	Circuit Asm
29	830398	Box Switch		64	829971-6	Switch Reset Asm
30	169123-2	Relief Strain		65	805549-22	Washer #10
31	138164	* Lockwasher #8				13/64 x 3/8 x .031
32	827925	Bolt Carriage 1/2-13 x 1-1/2		66	SP6499	Owners Manual - English
33	827873	Nut Push 1/2		67	SP6499S	Owners Manual - Spanish
34	827921	Washer Flat Nylon		68	SP6499F	Owners Manual - French
35	827548	Wrench Arbor

*Standard Hardware Item - May be purchased locally

†These parts are available where you purchased your saw.

59

Image 59

Contents Page Table of Contents Before Using The Saw Safety Instructions For Table SawInspect your saw Reduce the Risk of Dangerous EnvironmentTo reduce the risk of injury from unexpected saw movement Inspect your work area Inspect Your BladeInspect your workpiece Safety Instructions For Table SawsDress for safety Plan your workBefore freeing jammed material Reduce the Risk of Accidental StartingKeep Children Away Don’t Force ToolBefore Starting To reduce the risk of throwback of cut off piecesTo remove loose pieces beneath or trapped inside the guard Before Leaving The SawWhile Cutting Glossary of Terms for WoodworkingResin Push StickPush Block RabbetMotor Specifications and Electrical Requirements Motor Specifications and Electrical Requirements Extension Gauge Cord Length Wire SizesThermal Overload Protector Thermal Overload DeviceUnpacking and Checking Contents Getting to Know Your Table Saw Lever...Locks the sliding table exten- sion Table...provides working surface to support workpieces Key SwitchSawdust Ejection Port Guard Latches Blade Wrench Wing Nut Fence Miter Gauge Wrench/Blade StorageRip Fence Storage Miter Gauge StorageChecking Table Insert AlignmentTools Needed Remove Foam Motor SupportSquare Groove To check for parallelismMarked ToothSawblade Combination Miter GaugeAlignment Square Blade Pointer at Position Stopscrew Checking Blade Tilt, or Squareness of Blade to TableTo Check For Squareness, 90 Position If blade is square to tableScale Screws Stopscrew To check for alignment, 45 PositionIf blade is 45 to table Pages Rip Scale Hold Down Adjusting Rip Fence Guide BarsAligning Rip Fence Guide Bars Combination Square Rip Fence Alignment AdjustmentAligning Sliding Table Extension Rip Indicator Rip Fence Lock Lever AdjustmentAdjusting Rip Indicator Adjusting NutHex Locking Front Hex Nut Coupling Installing Blade GuardIf the sliding table extension moves when locked Checking Sliding Table ExtensionDo not loosen other screws. This Aligning Blade GuardWood Kerf Spreader BladeRemoving and Installing Sawblade Miter Gauge Alignment Blade Tilt Lock Nut Adjusting Bevel LockMarking Ind-I-Cut Using Marking the Ind-I-CutMounting Your Saw Workbench Mounting Using HardwareTable Saw Mounting Procedures Front of Table Saw Diagram of Workbench Mounting HolesSupporting Table Saw with Sawhorses Workbench Mounting Using C ClampsBefore Each Use Inspect your saw Safety Instructions for Basic Saw OperationsPlan your cut Whenever Sawblade Is Spinning Work Feed Devices Push Block For Use with Auxiliary Fence Push StickAuxiliary Fence Fence Facing Crosscutting Using the Miter GaugeAdditional Safety Instructions for Crosscutting Basic Saw OperationsClamp Wood Block Cut Off Piece Repetitive CrosscuttingCompound Crosscutting Miter CrosscuttingBevel Crosscutting While Thru sawing Using the Rip FenceAdditional Safety Instructions for Rip Cuts Blade Path RippingOnce the trailing end is on the table Push Block Workpiece Auxiliary Fence Baffle Bevel Ripping Narrow WorkAuxiliary Fence Clamp Push Using Featherboards for Thru SawingMight otherwise pinch the blade Kerf and cause a kickbackUsing Featherboards for Non-Thru Sawing Kickback Install blade guard immediatelyUsing Carbide Tipped Blades ResawingDado InsertSaw Arbor DadoingPloughing and Molding RabbetingMolding Auxiliary Fence MoldingMaintaining Your Table Saw MaintenanceAdjusting Nylon Set Screw Ofadfa=oÉÅçããÉåÇë=íÜÉ=cçääçïáåÖ=ÅÅÉëëçêáÉë Trouble Probable Cause Remedy TroubleshootingGeneral Trouble Probable Cause Remedy MotorParts List for Ridgid 10 Inch Table Saw Model No. TS24001 Repair PartsKey Description Always Order by Part Number not by Key NumberRepair Parts Key Description 827483 Cover Blade Parts List for Ridgid 10 Inch Table Saw Model TS24001Always Order by Part Number Not by Key Number Description Miter Gauge AssemblyFence Assembly Guard Assembly Page Page Page Stock No. TS2400 Model No. TS24001 Serial No RIDGID, INC