RIDGID Table Saw manual Wrench/Blade Storage, Rip Fence Storage, Miter Gauge Storage

Page 19

Blade Guard Storage

Holds the blade guard when making non- thru cuts and transporting saw. Slide blade guard in as shown. Snap bottom edge of clear basket between latches on base.

Wrench/Blade Storage

Conveniently stores arbor wrenches as well as an extra sawblade. Secure wrenches and sawblade with blade stor- age washer and wing nut. Extra washers are provided to separate blades and pre- vent tooth damage.

Rip Fence Storage

Securely holds the rip fence when it is not being used. To insert, place the top edge in first and twist upward to snap in place. To remove pull up on fence and rotate bottom away from saw.

Miter Gauge Storage

Provides convenient storage for the miter gauge when it is not being used. Slide miter gauge in place as shown. To remove miter gauge release latch and lift straight up.

Guard

Latches

Blade

Wrench

Wing Nut

Fence

Latch

Miter Gauge

19

Image 19

Contents Page Table of Contents Before Using The Saw Safety Instructions For Table SawTo reduce the risk of injury from unexpected saw movement Reduce the Risk of Dangerous EnvironmentInspect your saw Inspect your work area Inspect Your BladeInspect your workpiece Safety Instructions For Table SawsDress for safety Plan your workBefore freeing jammed material Reduce the Risk of Accidental StartingKeep Children Away Don’t Force ToolBefore Starting To reduce the risk of throwback of cut off piecesTo remove loose pieces beneath or trapped inside the guard Before Leaving The SawWhile Cutting Glossary of Terms for WoodworkingResin Push StickPush Block RabbetMotor Specifications and Electrical Requirements Motor Specifications and Electrical Requirements Extension Gauge Cord Length Wire SizesThermal Overload Protector Thermal Overload DeviceUnpacking and Checking Contents Getting to Know Your Table Saw Lever...Locks the sliding table exten- sion Table...provides working surface to support workpieces Key SwitchSawdust Ejection Port Guard Latches Blade Wrench Wing Nut Fence Miter Gauge Wrench/Blade StorageRip Fence Storage Miter Gauge StorageChecking Table Insert AlignmentTools Needed Remove Foam Motor SupportSquare Groove To check for parallelismMarked ToothSawblade Combination Miter GaugeAlignment Square Blade Pointer at Position Stopscrew Checking Blade Tilt, or Squareness of Blade to TableTo Check For Squareness, 90 Position If blade is square to tableIf blade is 45 to table To check for alignment, 45 PositionScale Screws Stopscrew Aligning Rip Fence Guide Bars Adjusting Rip Fence Guide BarsPages Rip Scale Hold Down Aligning Sliding Table Extension Rip Fence Alignment AdjustmentCombination Square Rip Indicator Rip Fence Lock Lever AdjustmentAdjusting Rip Indicator Adjusting NutHex Locking Front Hex Nut Coupling Installing Blade GuardIf the sliding table extension moves when locked Checking Sliding Table ExtensionDo not loosen other screws. This Aligning Blade GuardWood Kerf Spreader BladeRemoving and Installing Sawblade Miter Gauge Alignment Blade Tilt Lock Nut Adjusting Bevel LockMarking Ind-I-Cut Using Marking the Ind-I-CutMounting Your Saw Workbench Mounting Using HardwareTable Saw Mounting Procedures Front of Table Saw Diagram of Workbench Mounting HolesSupporting Table Saw with Sawhorses Workbench Mounting Using C ClampsBefore Each Use Inspect your saw Safety Instructions for Basic Saw OperationsPlan your cut Whenever Sawblade Is Spinning Work Feed Devices Push Block For Use with Auxiliary Fence Push StickAuxiliary Fence Fence Facing Crosscutting Using the Miter GaugeAdditional Safety Instructions for Crosscutting Basic Saw OperationsClamp Wood Block Cut Off Piece Repetitive CrosscuttingBevel Crosscutting Miter CrosscuttingCompound Crosscutting Additional Safety Instructions for Rip Cuts Using the Rip FenceWhile Thru sawing Once the trailing end is on the table RippingBlade Path Auxiliary Fence Clamp Bevel Ripping Narrow WorkPush Block Workpiece Auxiliary Fence Baffle Push Using Featherboards for Thru SawingMight otherwise pinch the blade Kerf and cause a kickbackUsing Featherboards for Non-Thru Sawing Kickback Install blade guard immediatelyUsing Carbide Tipped Blades ResawingDado InsertSaw Arbor DadoingPloughing and Molding RabbetingMolding Auxiliary Fence MoldingAdjusting Nylon Set Screw MaintenanceMaintaining Your Table Saw Ofadfa=oÉÅçããÉåÇë=íÜÉ=cçääçïáåÖ=ÅÅÉëëçêáÉë General TroubleshootingTrouble Probable Cause Remedy Trouble Probable Cause Remedy MotorParts List for Ridgid 10 Inch Table Saw Model No. TS24001 Repair PartsKey Description Always Order by Part Number not by Key NumberRepair Parts Key Description 827483 Cover Blade Parts List for Ridgid 10 Inch Table Saw Model TS24001Always Order by Part Number Not by Key Number Description Miter Gauge AssemblyFence Assembly Guard Assembly Page Page Page Stock No. TS2400 Model No. TS24001 Serial No RIDGID, INC