RIDGID Table Saw manual Rip Fence Lock Lever Adjustment, Adjusting Rip Indicator, Adjusting Nut

Page 27

Rip Fence Lock Lever Adjustment

The rip fence lock lever, when locked down, should hold the rip fence securely. The lever should not be difficult to push down and lock.

To assure proper fence lock adjust- ment:

a. Raise lock lever and push fence head toward rear of saw.

b. Hold fence head down onto front guide bar while lifting rear of fence up and down.

c. Tighten adjusting nut until fence clamp just barely touches rear guide bar.

d. This should provide the best fence adjustment possible without over tightening.

Adjusting

Nut

Fence

Clamp

Rear Guide

Bar

Fence Clamp and Rear Guide Bar

Should Barely Touch When

Fence is Raised

Adjusting Rip Indicator

1.Raise the blade up approximately 1".

2.Use a ruler to position the rip fence 6" to the right of the blade as shown. Lock the rip fence.

3.The rip indicator should read 6". If not:

•Slightly loosen the Phillips head screw.

•Slide the indicator left or right as required.

•Tighten the Phillips head screw.

Rip Indicator

6"

27

Image 27

Contents Page Table of Contents Before Using The Saw Safety Instructions For Table SawReduce the Risk of Dangerous Environment To reduce the risk of injury from unexpected saw movementInspect your saw Inspect your work area Inspect Your BladeInspect your workpiece Safety Instructions For Table SawsDress for safety Plan your workBefore freeing jammed material Reduce the Risk of Accidental StartingKeep Children Away Don’t Force ToolBefore Starting To reduce the risk of throwback of cut off piecesTo remove loose pieces beneath or trapped inside the guard Before Leaving The SawWhile Cutting Glossary of Terms for WoodworkingResin Push StickPush Block RabbetMotor Specifications and Electrical Requirements Motor Specifications and Electrical Requirements Extension Gauge Cord Length Wire SizesThermal Overload Protector Thermal Overload DeviceUnpacking and Checking Contents Getting to Know Your Table Saw Lever...Locks the sliding table exten- sion Table...provides working surface to support workpieces Key SwitchSawdust Ejection Port Guard Latches Blade Wrench Wing Nut Fence Miter Gauge Wrench/Blade StorageRip Fence Storage Miter Gauge StorageChecking Table Insert AlignmentTools Needed Remove Foam Motor SupportSquare Groove To check for parallelismMarked ToothSawblade Combination Miter GaugeAlignment Square Blade Pointer at Position Stopscrew Checking Blade Tilt, or Squareness of Blade to TableTo Check For Squareness, 90 Position If blade is square to tableTo check for alignment, 45 Position If blade is 45 to tableScale Screws Stopscrew Adjusting Rip Fence Guide Bars Aligning Rip Fence Guide BarsPages Rip Scale Hold Down Rip Fence Alignment Adjustment Aligning Sliding Table ExtensionCombination Square Rip Indicator Rip Fence Lock Lever AdjustmentAdjusting Rip Indicator Adjusting NutHex Locking Front Hex Nut Coupling Installing Blade GuardIf the sliding table extension moves when locked Checking Sliding Table ExtensionDo not loosen other screws. This Aligning Blade GuardWood Kerf Spreader BladeRemoving and Installing Sawblade Miter Gauge Alignment Blade Tilt Lock Nut Adjusting Bevel LockMarking Ind-I-Cut Using Marking the Ind-I-CutMounting Your Saw Workbench Mounting Using HardwareTable Saw Mounting Procedures Front of Table Saw Diagram of Workbench Mounting HolesSupporting Table Saw with Sawhorses Workbench Mounting Using C ClampsBefore Each Use Inspect your saw Safety Instructions for Basic Saw OperationsPlan your cut Whenever Sawblade Is Spinning Work Feed Devices Push Block For Use with Auxiliary Fence Push StickAuxiliary Fence Fence Facing Crosscutting Using the Miter GaugeAdditional Safety Instructions for Crosscutting Basic Saw OperationsClamp Wood Block Cut Off Piece Repetitive CrosscuttingMiter Crosscutting Bevel CrosscuttingCompound Crosscutting Using the Rip Fence Additional Safety Instructions for Rip CutsWhile Thru sawing Ripping Once the trailing end is on the tableBlade Path Bevel Ripping Narrow Work Auxiliary Fence ClampPush Block Workpiece Auxiliary Fence Baffle Push Using Featherboards for Thru SawingMight otherwise pinch the blade Kerf and cause a kickbackUsing Featherboards for Non-Thru Sawing Kickback Install blade guard immediatelyUsing Carbide Tipped Blades ResawingDado InsertSaw Arbor DadoingPloughing and Molding RabbetingMolding Auxiliary Fence MoldingMaintenance Adjusting Nylon Set ScrewMaintaining Your Table Saw Ofadfa=oÉÅçããÉåÇë=íÜÉ=cçääçïáåÖ=ÅÅÉëëçêáÉë Troubleshooting GeneralTrouble Probable Cause Remedy Trouble Probable Cause Remedy MotorParts List for Ridgid 10 Inch Table Saw Model No. TS24001 Repair PartsKey Description Always Order by Part Number not by Key NumberRepair Parts Key Description 827483 Cover Blade Parts List for Ridgid 10 Inch Table Saw Model TS24001Always Order by Part Number Not by Key Number Description Miter Gauge AssemblyFence Assembly Guard Assembly Page Page Page Stock No. TS2400 Model No. TS24001 Serial No RIDGID, INC