RIDGID Table Saw manual Miter Crosscutting, Bevel Crosscutting, Compound Crosscutting

Page 44

Basic Saw Operations (continued)

Miter Crosscutting

Miter cutting is cutting wood at an angle other than 90° with the edge of the wood. Follow the same procedure as you would for crosscutting.

Adjust the miter gauge to the desired angle, and lock it.

The miter gauge may be used in either of the grooves in the table. Make sure it is locked.

When using the miter gauge in the left hand groove, hold the workpiece firmly against the miter gauge head with your left hand, and grip the lock knob with your right hand.

When using the miter gauge in the right hand groove, hold the workpiece with your right hand and the lock knob with your left hand.

Bevel Crosscutting

Bevel crosscutting is the same as cross- cutting except that the wood is cut at an angle...other than 90° with the bottom flat side of the wood.

Adjust the blade to the desired angle.

Always use the miter gauge in the groove to the right of the blade. It can- not be used in the groove to the left because the blade guard will interfere. Hold the workpiece with your right hand and the lock knob with your left hand.

Use the auxiliary fence/work support for additional support of the workpiece.

Compound Crosscutting

Compound cutting is a combination of miter cutting and bevel crosscutting. The cut is made at an angle other than 90° to both the edge and the bottom flat side of the wood.

Adjust the miter gauge and the blade to the desired angle...Make sure miter gauge is locked.

44

Image 44
Contents Page Table of Contents Safety Instructions For Table Saw Before Using The SawInspect your saw Reduce the Risk of Dangerous EnvironmentTo reduce the risk of injury from unexpected saw movement Inspect Your Blade Inspect your work areaSafety Instructions For Table Saws Dress for safetyPlan your work Inspect your workpieceReduce the Risk of Accidental Starting Keep Children AwayDon’t Force Tool Before freeing jammed materialTo reduce the risk of throwback of cut off pieces To remove loose pieces beneath or trapped inside the guardBefore Leaving The Saw Before StartingGlossary of Terms for Woodworking While CuttingPush Stick Push BlockRabbet ResinMotor Specifications and Electrical Requirements Motor Specifications and Electrical Requirements Wire Sizes Thermal Overload ProtectorThermal Overload Device Extension Gauge Cord LengthUnpacking and Checking Contents Getting to Know Your Table Saw Lever...Locks the sliding table exten- sion Key Switch Table...provides working surface to support workpiecesSawdust Ejection Port Wrench/Blade Storage Rip Fence StorageMiter Gauge Storage Guard Latches Blade Wrench Wing Nut Fence Miter GaugeAlignment Tools NeededRemove Foam Motor Support Checking Table InsertTo check for parallelism Marked ToothSawbladeCombination Miter Gauge Square GrooveAlignment Checking Blade Tilt, or Squareness of Blade to Table To Check For Squareness, 90 PositionIf blade is square to table Square Blade Pointer at Position StopscrewScale Screws Stopscrew To check for alignment, 45 PositionIf blade is 45 to table Pages Rip Scale Hold Down Adjusting Rip Fence Guide BarsAligning Rip Fence Guide Bars Combination Square Rip Fence Alignment AdjustmentAligning Sliding Table Extension Rip Fence Lock Lever Adjustment Adjusting Rip IndicatorAdjusting Nut Rip IndicatorInstalling Blade Guard If the sliding table extension moves when lockedChecking Sliding Table Extension Hex Locking Front Hex Nut CouplingAligning Blade Guard WoodKerf Spreader Blade Do not loosen other screws. ThisRemoving and Installing Sawblade Miter Gauge Alignment Adjusting Bevel Lock Marking Ind-I-Cut UsingMarking the Ind-I-Cut Blade Tilt Lock NutWorkbench Mounting Using Hardware Table Saw Mounting ProceduresFront of Table Saw Diagram of Workbench Mounting Holes Mounting Your SawWorkbench Mounting Using C Clamps Supporting Table Saw with SawhorsesSafety Instructions for Basic Saw Operations Before Each Use Inspect your sawPlan your cut Whenever Sawblade Is Spinning Work Feed Devices Push Stick Push Block For Use with Auxiliary FenceAuxiliary Fence Fence Facing Using the Miter Gauge Additional Safety Instructions for CrosscuttingBasic Saw Operations CrosscuttingRepetitive Crosscutting Clamp Wood Block Cut Off PieceCompound Crosscutting Miter CrosscuttingBevel Crosscutting While Thru sawing Using the Rip FenceAdditional Safety Instructions for Rip Cuts Blade Path RippingOnce the trailing end is on the table Push Block Workpiece Auxiliary Fence Baffle Bevel Ripping Narrow WorkAuxiliary Fence Clamp Using Featherboards for Thru Sawing Might otherwise pinch the bladeKerf and cause a kickback PushUsing Featherboards for Non-Thru Sawing Install blade guard immediately Using Carbide Tipped BladesResawing KickbackDadoing Dado InsertSaw ArborRabbeting Ploughing and MoldingMolding Molding Auxiliary FenceMaintaining Your Table Saw MaintenanceAdjusting Nylon Set Screw Ofadfa=oÉÅçããÉåÇë=íÜÉ=cçääçïáåÖ=ÅÅÉëëçêáÉë Trouble Probable Cause Remedy TroubleshootingGeneral Motor Trouble Probable Cause RemedyRepair Parts Parts List for Ridgid 10 Inch Table Saw Model No. TS24001Always Order by Part Number not by Key Number Key DescriptionRepair Parts Parts List for Ridgid 10 Inch Table Saw Model TS24001 Key Description 827483 Cover BladeMiter Gauge Assembly Always Order by Part Number Not by Key Number DescriptionFence Assembly Guard Assembly Page Page Page RIDGID, INC Stock No. TS2400 Model No. TS24001 Serial No