RIDGID MS1250LZ1 manual To Install Blade, Screw Blade Bolt Cover Lower Guard, Laser Guide

Page 17

ASSEMBLY

WARNING:

In some operations, the work clamp assembly may interfere with the operation of the blade guard as- sembly. Always make sure there is no interference with the blade guard prior to beginning any cutting operation to reduce the risk of serious personal injury.

TO INSTALL BLADE

See Figure 14.

WARNING:

A 12 in. blade is the maximum blade capacity of the saw. Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. Larger blades will come in contact with the blade guards, while thicker blades will prevent the hex bolt from securing the blade on the spindle. Either of these situations could result in a serious accident and can cause serious personal injury.

Unplug the saw.

Raise saw arm.

Rotate lower blade guard up and loosen screw. Rotate blade bolt cover up and back to expose the hex bolt.

Depress the spindle lock button and rotate the hex bolt until the spindle locks.

Using the wrench provided, loosen and remove the hex bolt.

NOTE: The hex bolt has left hand threads. Turn hex bolt clockwise to loosen.

Remove the outer blade washer or the laser guide. Do not remove the inner blade washer.

Wipe a drop of oil onto the inner blade washer or the laser guide and the outer blade washer or laser guide where they contact the blade.

WARNING:

If inner blade washer has been removed, replace it before placing blade on spindle. Failure to do so could cause an accident since blade will not tighten properly.

Fit saw blade inside lower blade guard and onto spindle. The blade teeth point downward at the front of saw as shown in figure 14.

SCREW

BLADE BOLT

COVER

LOWER

BLADE

GUARD

BLADE

TO

SCREW

LOOSEN

FLAT

ON SPINDLE

TO

TIGHTEN

HEX

 

BOLT

INNER BLADE

LASER GUIDE

WASHER WITH

OR OUTER

DOUBLE "D" FLATS

BLADE WASHER

Fig. 14

 

CAUTION:

Always install the blade with the blade teeth and the arrow printed on the side of the blade pointing down at the front of the saw. The direction of blade rotation is also stamped with an arrow on the upper blade guard.

Replace outer blade washer or the laser guide. The double "D" flats on the blade washers align with the flats on the spindle.

Depress spindle lock button and replace hex bolt.

NOTE: The hex bolt has left hand threads. Turn blade bolt counterclockwise to tighten.

Tighten hex bolt securely.

Replace the lower blade guard and blade bolt cover.

Replace screw and tighten securely.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents OPERATOR’S Manual Introduction Table of Contents Blade Coasts After Being Turned OFF General Safety RulesRead ALL Instructions  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Specific Safety RulesSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Cord Length Wire Size A.W.GDouble Insulation Electrical ConnectionGlossary of Terms Miter FeaturesProduct Specifications Know Your Compound Miter SAW Switch TriggerAMP Motor 12 IN. BladeTools Needed Socket Head Screws Washer Extention Dust BAG Blade Wrench Loose PartsDust Guide HEX Bolt Unpacking AssemblyMounting Holes Trace Holes AT These Locations For Hole Pattern SAW BaseDust Guide Table ExtensionExtension Washer Socket Head Washer Screw Tighten Upper Blade Guard Dust Guide Exhaust PortWork Clamp Dust BAGQuick SAWLaser Guide To Install BladeScrew Blade Bolt Cover Lower Guard Aligning the Laser Guide Line Mounting the Exactline Laser GuideSquaring the SAW Blade to the Fence Cutting a Slot in the Zero Clearance Throat PlateSee Figures 17 Broken RED LineAdjustments are Required Sliding Miter Fence Blade See Figures 22 Squaring the Blade to the Miter TableLock Knob CombinationBevel Pivot Adjustment Pivot Adjustments Travel Pivot AdjustmentOperation ApplicationsStraight Crosscut Work Clamp Cutting with Your Compound Miter SAWTo Crosscut Indicator Point Screw Bevel CUT Work Clamp Stop PIN Bevel Scale IndicatorTo Bevel CUT See Figures 27Compound Miter CUT Work Clamp To Compound Miter CUTSee Figures 30 Support Long Workpieces45 x 45 Compound Miter CUT Long Workpiece SupportsPitch Side COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters Laying Molding Flat on the Miter Table Cutting Crown MoldingCeiling Inside Corner FenceMaking a Crown Molding Support JIG Using a Crown Molding Support JIGCutting Warped Material See Figures 34General Maintenance MaintenanceClamping Wide Workpieces LubricationProceed as follows when replacement is required Brush ReplacementBrush Assembly Brush CAPDo not attempt to activate the laser Changing the BatteriesDAY Satisfaction Guarantee Policy WarrantyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredModel No MS1250LZ1 Serial No Customer Service Information

MS1250LZ1 specifications

The RIDGID MS1250LZ1 is a state-of-the-art miter saw designed to meet the demands of professionals and DIY enthusiasts alike. With its robust construction and innovative features, this powerful tool is optimally engineered for precision cutting and versatility in various applications.

One of the standout features of the MS1250LZ1 is its 12-inch carbide-tipped blade, which provides outstanding cutting capacity. This generous blade size enables users to cut through larger materials with ease, making it ideal for framing, trimming, and even crosscuts. The saw’s powerful motor drives the blade at an impressive no-load speed, ensuring smooth and efficient cuts through hardwoods, softwoods, and composite materials.

The MS1250LZ1 incorporates advanced miter and bevel cutting capabilities. It offers an easy-to-adjust miter angle ranging from 0 to 52 degrees, allowing for accurate cuts in various directions. Additionally, the bevel capability can be adjusted up to 45 degrees to the left, providing more flexibility in creating complex cuts. This is particularly handy for crown molding, baseboards, and other intricate woodworking projects.

Safety is a significant consideration in the design of the RIDGID MS1250LZ1. It features a blade guard that provides optimal protection while allowing for a clear view of the cutting area. The electric brake ensures the blade stops quickly after use, reducing the risk of accidents. Furthermore, the saw is equipped with a horizontal handle that enhances control, reducing fatigue during prolonged use.

The tool comes with an integrated laser guide that illuminates the cutting line for enhanced accuracy. This technology fine-tunes the cutting process, ensuring precise results even in low-light conditions. The built-in dust collection system helps keep your workspace clean by capturing sawdust and debris, promoting a safer and more efficient working environment.

Constructed with durability in mind, the MS1250LZ1 features a solid, heavy-duty base for improved stability. This stability is key during critical cuts, reducing vibrations that could affect accuracy.

Overall, the RIDGID MS1250LZ1 is a reliable and efficient miter saw that combines power, precision, and user-friendly features. Whether you're tackling professional projects or home improvements, this miter saw stands out as an essential tool for achieving flawless, quality results.
Top Page Image Contents