RIDGID MS1250LZ1 manual Support Long Workpieces, See Figures 30, 45 x 45 Compound Miter CUT

Page 26

OPERATION

Align the cutting line on the workpiece with the edge of saw blade.

Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece when possible. See Figure 30.

Before turning on the saw, perform a dry run of the cutting operation just to make sure that no problems will occur when the cut is made.

Grasp the saw handle firmly. Depress the switch lock with thumb then squeeze the switch trigger. Allow several seconds for the blade to reach maximum speed.

Slowly lower the blade into and through the workpiece.

See Figures 30 - 31.

Release the switch trigger and allow the saw blade to stop rotating before raising the blade out of workpiece. Wait until the electric brake stops blade from turning before removing the workpiece from miter table.

SUPPORT LONG WORKPIECES

See Figure 32.

Long workpieces need extra supports. Supports should be

 

placed along the workpiece so it does not sag. The support

 

should let the workpiece lay flat on the base of the saw and

45° x 45° COMPOUND MITER CUT

work table during the cutting operation. Use the optional

Fig. 31

work clamp or a C-clamp to secure the workpiece.

 

LONG

WORKPIECE

4 1

WORKPIECE

SUPPORTS

Fig. 32

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents OPERATOR’S Manual Table of Contents Introduction Blade Coasts After Being Turned OFF General Safety RulesRead ALL Instructions Specific Safety Rules  Before Making a CUT, be Sure ALL ADJUST- Ments are SecureSpecific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningDouble Insulation Cord Length Wire Size A.W.GElectrical Electrical ConnectionGlossary of Terms Miter FeaturesProduct Specifications AMP Motor Switch TriggerKnow Your Compound Miter SAW 12 IN. BladeTools Needed Socket Head Screws Washer Extention Dust BAG Blade Wrench Loose PartsDust Guide HEX Bolt Mounting Holes AssemblyUnpacking Trace Holes AT These Locations For Hole Pattern SAW BaseExtension Washer Socket Head Washer Screw Tighten Table ExtensionDust Guide Upper Blade Guard Dust Guide Exhaust PortQuick Dust BAGWork Clamp SAWLaser Guide To Install BladeScrew Blade Bolt Cover Lower Guard Mounting the Exactline Laser Guide Aligning the Laser Guide LineSee Figures 17 Cutting a Slot in the Zero Clearance Throat PlateSquaring the SAW Blade to the Fence Broken RED LineAdjustments are Required Sliding Miter Fence Blade Lock Knob Squaring the Blade to the Miter TableSee Figures 22 CombinationOperation Pivot Adjustments Travel Pivot AdjustmentBevel Pivot Adjustment ApplicationsStraight Crosscut Work Clamp Cutting with Your Compound Miter SAWTo Crosscut To Bevel CUT Bevel Scale IndicatorIndicator Point Screw Bevel CUT Work Clamp Stop PIN See Figures 27To Compound Miter CUT Compound Miter CUT Work Clamp45 x 45 Compound Miter CUT Support Long WorkpiecesSee Figures 30 Long Workpiece SupportsPitch Side COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters Ceiling Cutting Crown MoldingLaying Molding Flat on the Miter Table Inside Corner FenceCutting Warped Material Using a Crown Molding Support JIGMaking a Crown Molding Support JIG See Figures 34Clamping Wide Workpieces MaintenanceGeneral Maintenance LubricationBrush Assembly Brush ReplacementProceed as follows when replacement is required Brush CAPChanging the Batteries Do not attempt to activate the laserWhat is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not CoveredCustomer Service Information Model No MS1250LZ1 Serial No

MS1250LZ1 specifications

The RIDGID MS1250LZ1 is a state-of-the-art miter saw designed to meet the demands of professionals and DIY enthusiasts alike. With its robust construction and innovative features, this powerful tool is optimally engineered for precision cutting and versatility in various applications.

One of the standout features of the MS1250LZ1 is its 12-inch carbide-tipped blade, which provides outstanding cutting capacity. This generous blade size enables users to cut through larger materials with ease, making it ideal for framing, trimming, and even crosscuts. The saw’s powerful motor drives the blade at an impressive no-load speed, ensuring smooth and efficient cuts through hardwoods, softwoods, and composite materials.

The MS1250LZ1 incorporates advanced miter and bevel cutting capabilities. It offers an easy-to-adjust miter angle ranging from 0 to 52 degrees, allowing for accurate cuts in various directions. Additionally, the bevel capability can be adjusted up to 45 degrees to the left, providing more flexibility in creating complex cuts. This is particularly handy for crown molding, baseboards, and other intricate woodworking projects.

Safety is a significant consideration in the design of the RIDGID MS1250LZ1. It features a blade guard that provides optimal protection while allowing for a clear view of the cutting area. The electric brake ensures the blade stops quickly after use, reducing the risk of accidents. Furthermore, the saw is equipped with a horizontal handle that enhances control, reducing fatigue during prolonged use.

The tool comes with an integrated laser guide that illuminates the cutting line for enhanced accuracy. This technology fine-tunes the cutting process, ensuring precise results even in low-light conditions. The built-in dust collection system helps keep your workspace clean by capturing sawdust and debris, promoting a safer and more efficient working environment.

Constructed with durability in mind, the MS1250LZ1 features a solid, heavy-duty base for improved stability. This stability is key during critical cuts, reducing vibrations that could affect accuracy.

Overall, the RIDGID MS1250LZ1 is a reliable and efficient miter saw that combines power, precision, and user-friendly features. Whether you're tackling professional projects or home improvements, this miter saw stands out as an essential tool for achieving flawless, quality results.
Top Page Image Contents