RIDGID MS1250LZ1 manual Cutting a Slot in the Zero Clearance Throat Plate, See Figures 17

Page 19

ASSEMBLY

Follow the directions below for using the laser guide:

Removing Your Mark:

Position the laser line near the left edge of your mark on the work surface in order to remove the mark.

To Cut Your Mark:

Position the laser line near or over your mark on the work surface in order to cut the mark.

To Leave Your Mark:

Position the laser line near the right edge of your mark on the work surface in order to leave the mark.

After you have become familiar with using the laser guide, you will be able to remove, cut, or leave your mark on the work surface. Practice will teach you the correct position for aligning the laser line with your mark.

CUTTING A SLOT IN THE ZERO CLEARANCE THROAT PLATE

In order to use your compound miter saw, you must cut a slot through the zero clearance throat plate to allow for blade clearance. To cut the slot, set your saw at 0° miter, turn saw on and allow the blade to reach full speed, then carefully make a straight cut as far as it will go through the throat plate. Turn your saw off and allow the blade to come to a complete stop before raising the saw arm.

Next, adjust the bevel angle to 45°, turn your saw on and al- low the blade to reach full speed, then carefully make another cut through the zero clearance throat plate. The slot in the throat plate will then be wide enough to allow the blade to pass through it at any angle from 0° to 45°.

NOTE: Many of the illustrations in this manual show only portions of your compound miter saw. This is intentional so that we can clearly show points being made in the illustra- tions. Never operate your saw without all guards securely in place and in good operating condition.

SQUARING THE SAW BLADE TO THE FENCE

See Figures 17 - 21

Unplug your saw.

WARNING:

Failure to unplug your saw could result in accidental starting causing possible serious personal injury.

Remove the screws holding the throat plate in place. Remove the throat plate.

Pull the saw arm all the way down and engage the lock pin to hold the saw arm in transport position.

Loosen the miter lock handle approximately one-half turn.

4 1

BROKEN

RED LINE

Fig. 16

SOCKET HEAD

SOCKET HEAD

SCREW(S)

SCREW(S)

FENCE

 

 

Fig. 17

SLIDING

 

 

MITER

 

 

FENCE

 

BLADE

 

 

MITER

 

 

LOCK

 

 

PLATE

 

 

MITER

MITER

FRAMING

LOCK

SQUARE

HANDLE

TABLE

 

 

 

VIEW OF BLADE SQUARE WITH FENCE

Fig. 18

 

 

19

Image 19
Contents OPERATOR’S Manual Introduction Table of ContentsRead ALL Instructions General Safety Rules Blade Coasts After Being Turned OFF  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Specific Safety RulesSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Connection Cord Length Wire Size A.W.GElectrical Double InsulationGlossary of Terms Product Specifications FeaturesMiter 12 IN. Blade Switch TriggerKnow Your Compound Miter SAW AMP MotorTools Needed Dust Guide HEX Bolt Loose PartsSocket Head Screws Washer Extention Dust BAG Blade Wrench Trace Holes AT These Locations For Hole Pattern SAW Base AssemblyUnpacking Mounting HolesUpper Blade Guard Dust Guide Exhaust Port Table ExtensionDust Guide Extension Washer Socket Head Washer Screw TightenSAW Dust BAGWork Clamp QuickScrew Blade Bolt Cover Lower Guard To Install BladeLaser Guide Aligning the Laser Guide Line Mounting the Exactline Laser GuideBroken RED Line Cutting a Slot in the Zero Clearance Throat PlateSquaring the SAW Blade to the Fence See Figures 17Adjustments are Required Sliding Miter Fence Blade Combination Squaring the Blade to the Miter TableSee Figures 22 Lock KnobApplications Pivot Adjustments Travel Pivot AdjustmentBevel Pivot Adjustment OperationTo Crosscut Cutting with Your Compound Miter SAWStraight Crosscut Work Clamp See Figures 27 Bevel Scale IndicatorIndicator Point Screw Bevel CUT Work Clamp Stop PIN To Bevel CUTCompound Miter CUT Work Clamp To Compound Miter CUTLong Workpiece Supports Support Long WorkpiecesSee Figures 30 45 x 45 Compound Miter CUTCutting Compound Miters COMPOUND-ANGLE Settings for Popular StructuresPitch Side Inside Corner Fence Cutting Crown MoldingLaying Molding Flat on the Miter Table CeilingSee Figures 34 Using a Crown Molding Support JIGMaking a Crown Molding Support JIG Cutting Warped MaterialLubrication MaintenanceGeneral Maintenance Clamping Wide WorkpiecesBrush CAP Brush ReplacementProceed as follows when replacement is required Brush AssemblyDo not attempt to activate the laser Changing the BatteriesHOW to Obtain Service What is not Covered WarrantyDAY Satisfaction Guarantee Policy What is Covered Under the 3 Year Limited Service WarrantyModel No MS1250LZ1 Serial No Customer Service Information

MS1250LZ1 specifications

The RIDGID MS1250LZ1 is a state-of-the-art miter saw designed to meet the demands of professionals and DIY enthusiasts alike. With its robust construction and innovative features, this powerful tool is optimally engineered for precision cutting and versatility in various applications.

One of the standout features of the MS1250LZ1 is its 12-inch carbide-tipped blade, which provides outstanding cutting capacity. This generous blade size enables users to cut through larger materials with ease, making it ideal for framing, trimming, and even crosscuts. The saw’s powerful motor drives the blade at an impressive no-load speed, ensuring smooth and efficient cuts through hardwoods, softwoods, and composite materials.

The MS1250LZ1 incorporates advanced miter and bevel cutting capabilities. It offers an easy-to-adjust miter angle ranging from 0 to 52 degrees, allowing for accurate cuts in various directions. Additionally, the bevel capability can be adjusted up to 45 degrees to the left, providing more flexibility in creating complex cuts. This is particularly handy for crown molding, baseboards, and other intricate woodworking projects.

Safety is a significant consideration in the design of the RIDGID MS1250LZ1. It features a blade guard that provides optimal protection while allowing for a clear view of the cutting area. The electric brake ensures the blade stops quickly after use, reducing the risk of accidents. Furthermore, the saw is equipped with a horizontal handle that enhances control, reducing fatigue during prolonged use.

The tool comes with an integrated laser guide that illuminates the cutting line for enhanced accuracy. This technology fine-tunes the cutting process, ensuring precise results even in low-light conditions. The built-in dust collection system helps keep your workspace clean by capturing sawdust and debris, promoting a safer and more efficient working environment.

Constructed with durability in mind, the MS1250LZ1 features a solid, heavy-duty base for improved stability. This stability is key during critical cuts, reducing vibrations that could affect accuracy.

Overall, the RIDGID MS1250LZ1 is a reliable and efficient miter saw that combines power, precision, and user-friendly features. Whether you're tackling professional projects or home improvements, this miter saw stands out as an essential tool for achieving flawless, quality results.