RIDGID MS1250LZ1 Squaring the Blade to the Miter Table, See Figures 22, Lock Knob, Combination

Page 21

ASSEMBLY

SQUARING THE BLADE TO THE MITER TABLE

BEVEL

 

See Figures 22 - 25.

LOCK

 

KNOB

 

Unplug your saw.

 

 

 

 

MITER

BLADE

WARNING:

FENCE

 

Failure to unplug your saw could result in accidental starting causing possible serious personal injury.

Pull the saw arm all the way down and engage the lock pin to hold the saw arm in transport position.

Loosen the miter lock handle approximately one-half turn.

Depress the miter lock plate and rotate the miter table until the pointer on the control arm is positioned at 0°.

Release the miter lock plate and securely tighten the miter lock handle.

Loosen bevel lock knob and set saw arm at 0° bevel (blade set 90° to miter table). Tighten bevel lock knob.

Place a combination square against the miter table and the flat part of saw blade.

NOTE: Make sure that the square contacts the flat part of the saw blade, not the blade teeth.

Rotate the blade by hand and check the blade-to-table alignment at several points.

 

MITER

MITER

MITER

 

LOCK PLATE

LOCK

COMBINATION

TABLE

 

HANDLE

SQUARE

CORRECT VIEW OF BLADE

SQUARE WITH MITER TABLE

Fig. 22

The edge of the square and the saw blade should be parallel as shown in figure 22.

If the top or bottom of the saw blade angles away from the square as shown in figures 22 and 24, adjustments

are needed.

Loosen the bevel lock knob.

Using the blade wrench, loosen the bevel stop adjustment screw and slide the bevel stop left or right as needed to bring the saw blade into alignment with the square. Retighten bevel stop adjustment screw. See Figure 25.

Retighten bevel lock knob. Recheck blade-to-table align- ment.

NOTE: The above procedure can be used to check blade squareness of the saw blade to the miter table at both 0° and 45° angles.

Your saw has several scale indicators. After squaring adjust- ments have been made, it may be necessary to loosen the indicators screws and reset them to zero. See Figure 21.

50

40

35

30

COMBINATION

SQUARE

VIEW OF BLADE NOT SQUARE WITH MITER TABLE,

ADJUSTMENTS ARE REQUIRED

Fig. 23

COMBINATION

SQUARE

VIEW OF BLADE NOT SQUARE WITH MITER TABLE,

ADJUSTMENTS ARE REQUIRED

Fig. 24

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents OPERATOR’S Manual Introduction Table of ContentsGeneral Safety Rules Read ALL Instructions Blade Coasts After Being Turned OFF  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Specific Safety RulesSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Cord Length Wire Size A.W.GDouble Insulation Electrical ConnectionGlossary of Terms Features Product SpecificationsMiter Know Your Compound Miter SAW Switch TriggerAMP Motor 12 IN. BladeTools Needed Loose Parts Dust Guide HEX BoltSocket Head Screws Washer Extention Dust BAG Blade Wrench Unpacking AssemblyMounting Holes Trace Holes AT These Locations For Hole Pattern SAW BaseDust Guide Table ExtensionExtension Washer Socket Head Washer Screw Tighten Upper Blade Guard Dust Guide Exhaust PortWork Clamp Dust BAGQuick SAWTo Install Blade Screw Blade Bolt Cover Lower GuardLaser Guide Aligning the Laser Guide Line Mounting the Exactline Laser GuideSquaring the SAW Blade to the Fence Cutting a Slot in the Zero Clearance Throat PlateSee Figures 17 Broken RED LineAdjustments are Required Sliding Miter Fence Blade See Figures 22 Squaring the Blade to the Miter TableLock Knob CombinationBevel Pivot Adjustment Pivot Adjustments Travel Pivot AdjustmentOperation ApplicationsCutting with Your Compound Miter SAW To CrosscutStraight Crosscut Work Clamp Indicator Point Screw Bevel CUT Work Clamp Stop PIN Bevel Scale IndicatorTo Bevel CUT See Figures 27Compound Miter CUT Work Clamp To Compound Miter CUTSee Figures 30 Support Long Workpieces45 x 45 Compound Miter CUT Long Workpiece SupportsCOMPOUND-ANGLE Settings for Popular Structures Cutting Compound MitersPitch Side Laying Molding Flat on the Miter Table Cutting Crown MoldingCeiling Inside Corner FenceMaking a Crown Molding Support JIG Using a Crown Molding Support JIGCutting Warped Material See Figures 34General Maintenance MaintenanceClamping Wide Workpieces LubricationProceed as follows when replacement is required Brush ReplacementBrush Assembly Brush CAPDo not attempt to activate the laser Changing the BatteriesDAY Satisfaction Guarantee Policy WarrantyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredModel No MS1250LZ1 Serial No Customer Service Information

MS1250LZ1 specifications

The RIDGID MS1250LZ1 is a state-of-the-art miter saw designed to meet the demands of professionals and DIY enthusiasts alike. With its robust construction and innovative features, this powerful tool is optimally engineered for precision cutting and versatility in various applications.

One of the standout features of the MS1250LZ1 is its 12-inch carbide-tipped blade, which provides outstanding cutting capacity. This generous blade size enables users to cut through larger materials with ease, making it ideal for framing, trimming, and even crosscuts. The saw’s powerful motor drives the blade at an impressive no-load speed, ensuring smooth and efficient cuts through hardwoods, softwoods, and composite materials.

The MS1250LZ1 incorporates advanced miter and bevel cutting capabilities. It offers an easy-to-adjust miter angle ranging from 0 to 52 degrees, allowing for accurate cuts in various directions. Additionally, the bevel capability can be adjusted up to 45 degrees to the left, providing more flexibility in creating complex cuts. This is particularly handy for crown molding, baseboards, and other intricate woodworking projects.

Safety is a significant consideration in the design of the RIDGID MS1250LZ1. It features a blade guard that provides optimal protection while allowing for a clear view of the cutting area. The electric brake ensures the blade stops quickly after use, reducing the risk of accidents. Furthermore, the saw is equipped with a horizontal handle that enhances control, reducing fatigue during prolonged use.

The tool comes with an integrated laser guide that illuminates the cutting line for enhanced accuracy. This technology fine-tunes the cutting process, ensuring precise results even in low-light conditions. The built-in dust collection system helps keep your workspace clean by capturing sawdust and debris, promoting a safer and more efficient working environment.

Constructed with durability in mind, the MS1250LZ1 features a solid, heavy-duty base for improved stability. This stability is key during critical cuts, reducing vibrations that could affect accuracy.

Overall, the RIDGID MS1250LZ1 is a reliable and efficient miter saw that combines power, precision, and user-friendly features. Whether you're tackling professional projects or home improvements, this miter saw stands out as an essential tool for achieving flawless, quality results.
Top Page Image Contents