RIDGID MS1250LZ1 manual Adjustments are Required Sliding Miter Fence Blade

Page 20

ASSEMBLY

Depress the miter lock plate and rotate the miter table

until the pointer on the control arm is positioned at 0°.

Release the miter lock plate and securely tighten the miter

lock handle.

Remove the sliding miter fence by loosening the set screw

and the sliding miter fence knob.

Lay a framing square flat on the miter table. Place one

leg of the square against the fence. Slide the other leg

of the square against the flat part of saw blade.

NOTE: Make sure that the square contacts the flat part

of the saw blade, not the blade teeth.

The edge of the square and the saw blade should be

parallel as shown in figure 18.

SLIDING

MITER

FENCE

BLADE

MITER FRAMING

TABLE SQUARE

VIEW OF BLADE NOT SQUARE WITH FENCE,

If the front or back edge of the saw blade angles away

from the square as shown in figures 19 and 20, adjust-

ments are needed.

Loosen the socket head screws that secure the miter

fence to the miter table. See Figure 17.

Rotate the miter fence left or right until the saw blade is

parallel with the square.

Retighten the screws securely and recheck the blade-to-

fence alignment.

Insert the throat plate and secure with the screws. Tighten

firmly. See instruction regarding “Cutting a Slot in the Zero

Clearance Throat Plate”.

ADJUSTMENTS ARE REQUIRED

SLIDING

MITER

FENCE

Fig. 19

BLADE

Your saw has several scale indicators. After squaring adjust- ments have been made, it may be necessary to loosen the indicators screws and reset them to zero. See Figure 21.

FRAMING

MITER SQUARE

TABLE

VIEW OF BLADE NOT SQUARE WITH FENCE,

ADJUSTMENTS ARE REQUIRED

Fig. 20

 

INDICATOR

SCALE

POINT

 

INDICATOR

BEVEL

 

SCALE

 

MITER

INDICATOR

SCALE

SCALE

SCREW

 

INDICATOR

INDICATOR

 

SCREW

Fig. 21

 

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents OPERATOR’S Manual Table of Contents Introduction Blade Coasts After Being Turned OFF General Safety RulesRead ALL Instructions Specific Safety Rules  Before Making a CUT, be Sure ALL ADJUST- Ments are SecureSpecific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningCord Length Wire Size A.W.G ElectricalDouble Insulation Electrical ConnectionGlossary of Terms Miter FeaturesProduct Specifications Switch Trigger Know Your Compound Miter SAWAMP Motor 12 IN. BladeTools Needed Socket Head Screws Washer Extention Dust BAG Blade Wrench Loose PartsDust Guide HEX Bolt Assembly UnpackingMounting Holes Trace Holes AT These Locations For Hole Pattern SAW BaseTable Extension Dust GuideExtension Washer Socket Head Washer Screw Tighten Upper Blade Guard Dust Guide Exhaust PortDust BAG Work ClampQuick SAWLaser Guide To Install BladeScrew Blade Bolt Cover Lower Guard Mounting the Exactline Laser Guide Aligning the Laser Guide LineCutting a Slot in the Zero Clearance Throat Plate Squaring the SAW Blade to the FenceSee Figures 17 Broken RED LineAdjustments are Required Sliding Miter Fence Blade Squaring the Blade to the Miter Table See Figures 22Lock Knob CombinationPivot Adjustments Travel Pivot Adjustment Bevel Pivot AdjustmentOperation ApplicationsStraight Crosscut Work Clamp Cutting with Your Compound Miter SAWTo Crosscut Bevel Scale Indicator Indicator Point Screw Bevel CUT Work Clamp Stop PINTo Bevel CUT See Figures 27To Compound Miter CUT Compound Miter CUT Work ClampSupport Long Workpieces See Figures 3045 x 45 Compound Miter CUT Long Workpiece SupportsPitch Side COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters Cutting Crown Molding Laying Molding Flat on the Miter TableCeiling Inside Corner FenceUsing a Crown Molding Support JIG Making a Crown Molding Support JIGCutting Warped Material See Figures 34Maintenance General MaintenanceClamping Wide Workpieces LubricationBrush Replacement Proceed as follows when replacement is requiredBrush Assembly Brush CAPChanging the Batteries Do not attempt to activate the laserWarranty DAY Satisfaction Guarantee PolicyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredCustomer Service Information Model No MS1250LZ1 Serial No

MS1250LZ1 specifications

The RIDGID MS1250LZ1 is a state-of-the-art miter saw designed to meet the demands of professionals and DIY enthusiasts alike. With its robust construction and innovative features, this powerful tool is optimally engineered for precision cutting and versatility in various applications.

One of the standout features of the MS1250LZ1 is its 12-inch carbide-tipped blade, which provides outstanding cutting capacity. This generous blade size enables users to cut through larger materials with ease, making it ideal for framing, trimming, and even crosscuts. The saw’s powerful motor drives the blade at an impressive no-load speed, ensuring smooth and efficient cuts through hardwoods, softwoods, and composite materials.

The MS1250LZ1 incorporates advanced miter and bevel cutting capabilities. It offers an easy-to-adjust miter angle ranging from 0 to 52 degrees, allowing for accurate cuts in various directions. Additionally, the bevel capability can be adjusted up to 45 degrees to the left, providing more flexibility in creating complex cuts. This is particularly handy for crown molding, baseboards, and other intricate woodworking projects.

Safety is a significant consideration in the design of the RIDGID MS1250LZ1. It features a blade guard that provides optimal protection while allowing for a clear view of the cutting area. The electric brake ensures the blade stops quickly after use, reducing the risk of accidents. Furthermore, the saw is equipped with a horizontal handle that enhances control, reducing fatigue during prolonged use.

The tool comes with an integrated laser guide that illuminates the cutting line for enhanced accuracy. This technology fine-tunes the cutting process, ensuring precise results even in low-light conditions. The built-in dust collection system helps keep your workspace clean by capturing sawdust and debris, promoting a safer and more efficient working environment.

Constructed with durability in mind, the MS1250LZ1 features a solid, heavy-duty base for improved stability. This stability is key during critical cuts, reducing vibrations that could affect accuracy.

Overall, the RIDGID MS1250LZ1 is a reliable and efficient miter saw that combines power, precision, and user-friendly features. Whether you're tackling professional projects or home improvements, this miter saw stands out as an essential tool for achieving flawless, quality results.
Top Page Image Contents