RIDGID MS1250LZ1 manual Specific Safety Rules

Page 5

SPECIFIC SAFETY RULES

NEVER hand hold a workpiece that is too small to be clamped. Keep hands clear of the cutting area.

NEVER reach behind, under, or within three inches of the blade and its cutting path with your hands and fingers for any reason.

NEVER reach to pick up a workpiece, a piece of scrap, or anything else that is in or near the cutting path of the blade.

AVOID AWKWARD OPERATIONS AND HAND POSITIONS where a sudden slip could cause your hand to move into the blade. ALWAYS make sure you have good balance. NEVER operate your miter saw on the floor or in a crouched position.

NEVER stand or have any part of your body in line with the path of the saw blade.

ALWAYS release the power switch and allow the saw blade to stop rotating before raising it out of the workpiece.

DO NOT TURN THE MOTOR SWITCH ON AND OFF RAPIDLY. This could cause the saw blade to loosen and could create a hazard. Should this ever occur, stand clear and allow the saw blade to come to a complete stop. Disconnect your saw from the power supply and securely retighten the blade bolt.

IF ANY PART OF THIS MITER SAW IS MISSING or should break, bend, or fail in any way, or should any electrical component fail to perform properly, shut off the power switch, remove the miter saw plug from the power source and have damaged, missing, or failed parts replaced before resuming operation.

IF THE POWER SUPPLY CORD IS DAMAGED, it must be replaced only by the manufacturer or by an authorized service center to avoid risk.

ALWAYS STAY ALERT! Do not allow familiarity (gained from frequent use of your saw) to cause a careless mis- take. ALWAYS REMEMBER that a careless fraction of a second is sufficient to inflict severe injury.

MAKE SURE THE WORK AREA HAS AMPLE LIGHTING to see the work and that no obstructions will interfere with safe operation BEFORE performing any work using your saw.

ALWAYS TURN OFF THE SAW before disconnecting it to avoid accidental starting when reconnecting to power supply. NEVER leave the saw unattended while connected to a power source.

THIS TOOL should have the following markings:

a)Wear eye protection.

b)Keep hands out of path of saw blade.

c)Do not operate saw without guards in place.

d)Do not perform any operation freehand.

e)Never reach around saw blade.

f)Turn off tool and wait for saw blade to stop before moving workpiece or changing settings.

g)Disconnect power (or unplug tool as applicable) before changing blade or servicing.

h)No load speed.

ALWAYS carry the tool only by the carrying handle.

AVOID direct eye exposure when using the laser guide.

SAVE THESE INSTRUCTIONS. Refer to them frequently and use to instruct other users. If you loan someone this tool, loan them these instructions also.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•lead from lead-based paints,

•crystalline silica from bricks and cement and other masonry products, and

•arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents OPERATOR’S Manual Introduction Table of Contents Blade Coasts After Being Turned OFF General Safety RulesRead ALL Instructions  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Specific Safety RulesSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Cord Length Wire Size A.W.GDouble Insulation Electrical ConnectionGlossary of Terms Miter FeaturesProduct Specifications Know Your Compound Miter SAW Switch TriggerAMP Motor 12 IN. BladeTools Needed Socket Head Screws Washer Extention Dust BAG Blade Wrench Loose PartsDust Guide HEX Bolt Unpacking AssemblyMounting Holes Trace Holes AT These Locations For Hole Pattern SAW BaseDust Guide Table ExtensionExtension Washer Socket Head Washer Screw Tighten Upper Blade Guard Dust Guide Exhaust PortWork Clamp Dust BAGQuick SAWLaser Guide To Install BladeScrew Blade Bolt Cover Lower Guard Aligning the Laser Guide Line Mounting the Exactline Laser GuideSquaring the SAW Blade to the Fence Cutting a Slot in the Zero Clearance Throat PlateSee Figures 17 Broken RED LineAdjustments are Required Sliding Miter Fence Blade See Figures 22 Squaring the Blade to the Miter TableLock Knob CombinationBevel Pivot Adjustment Pivot Adjustments Travel Pivot AdjustmentOperation ApplicationsStraight Crosscut Work Clamp Cutting with Your Compound Miter SAWTo Crosscut Indicator Point Screw Bevel CUT Work Clamp Stop PIN Bevel Scale IndicatorTo Bevel CUT See Figures 27Compound Miter CUT Work Clamp To Compound Miter CUTSee Figures 30 Support Long Workpieces45 x 45 Compound Miter CUT Long Workpiece SupportsPitch Side COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters Laying Molding Flat on the Miter Table Cutting Crown MoldingCeiling Inside Corner FenceMaking a Crown Molding Support JIG Using a Crown Molding Support JIGCutting Warped Material See Figures 34General Maintenance MaintenanceClamping Wide Workpieces LubricationProceed as follows when replacement is required Brush ReplacementBrush Assembly Brush CAPDo not attempt to activate the laser Changing the BatteriesDAY Satisfaction Guarantee Policy WarrantyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredModel No MS1250LZ1 Serial No Customer Service Information

MS1250LZ1 specifications

The RIDGID MS1250LZ1 is a state-of-the-art miter saw designed to meet the demands of professionals and DIY enthusiasts alike. With its robust construction and innovative features, this powerful tool is optimally engineered for precision cutting and versatility in various applications.

One of the standout features of the MS1250LZ1 is its 12-inch carbide-tipped blade, which provides outstanding cutting capacity. This generous blade size enables users to cut through larger materials with ease, making it ideal for framing, trimming, and even crosscuts. The saw’s powerful motor drives the blade at an impressive no-load speed, ensuring smooth and efficient cuts through hardwoods, softwoods, and composite materials.

The MS1250LZ1 incorporates advanced miter and bevel cutting capabilities. It offers an easy-to-adjust miter angle ranging from 0 to 52 degrees, allowing for accurate cuts in various directions. Additionally, the bevel capability can be adjusted up to 45 degrees to the left, providing more flexibility in creating complex cuts. This is particularly handy for crown molding, baseboards, and other intricate woodworking projects.

Safety is a significant consideration in the design of the RIDGID MS1250LZ1. It features a blade guard that provides optimal protection while allowing for a clear view of the cutting area. The electric brake ensures the blade stops quickly after use, reducing the risk of accidents. Furthermore, the saw is equipped with a horizontal handle that enhances control, reducing fatigue during prolonged use.

The tool comes with an integrated laser guide that illuminates the cutting line for enhanced accuracy. This technology fine-tunes the cutting process, ensuring precise results even in low-light conditions. The built-in dust collection system helps keep your workspace clean by capturing sawdust and debris, promoting a safer and more efficient working environment.

Constructed with durability in mind, the MS1250LZ1 features a solid, heavy-duty base for improved stability. This stability is key during critical cuts, reducing vibrations that could affect accuracy.

Overall, the RIDGID MS1250LZ1 is a reliable and efficient miter saw that combines power, precision, and user-friendly features. Whether you're tackling professional projects or home improvements, this miter saw stands out as an essential tool for achieving flawless, quality results.
Top Page Image Contents