Agilent Technologies 669xA, 665xA Table B-1.ARPS Commands continued, ARPS Command1, Description

Page 63

 

Table B-1. ARPS Commands (continued)

 

ARPS Command1

Description

Similar SCPI

 

 

Command

UNMASK?

This command reads which bits in the status register have been

STAT:OPER:ENAB?

 

enabled as fault conditions. The decimal equivalent of the total bit

STAT:QUES:ENAB?

 

weight of all enabled bits is returned.

ESE

 

 

 

FAULT?

This command reads which bits have been set in the fault register.

STAT:OPER?

 

A bit is set in the fault register when the corresponding bit in the

STAT:QUES?

 

status register changes from inactive to active AND the

*ESE

 

corresponding bit in the mask register has been enabled. The fault

 

 

register is reset only after it has been read. The decimal equivalent

 

 

of the total bit weight of all enabled bits is returned.

 

 

 

 

SRQ OFF

These commands enable or disable the power supply's ability to

*SRE

SRQ 0

request service from the controller for fault conditions. UNMASK

 

SR*Q ON

defines which conditions are defined as faults.

 

SRQ 1

Initial condition: SRQ OFF

 

 

 

 

SRQ?

This command reads the SRQ setting.

*SRE?

CLR

This command initializes the power supply to the power-on state.

*RST

 

It also resets the PON bit in the serial poll register. The command

 

 

performs the same function as the Device Clear (DCL) interface

 

 

message.

 

 

 

 

ERR?

This command determines the type of programming error detected

SYST:ERR?

 

by the supply. A remote programming error sets the ERR bit in the

 

 

status register, which can be enabled by UNMASK to request

 

 

service.

 

 

 

 

TEST?

This command causes the power supply to run selftest and report

*TST?

 

any detected failures.

 

 

 

 

ID?

This command causes the power supply to report its model number

*IDN?

 

and any options that affect the supply's output.

 

 

 

 

SYST:LANG

This command causes the alternate language to become active and

SYST:LANG

 

to be stored in nonvolatile memory. In this case, the commands are

 

 

equivalent. After being shut off, the power supply will resume in

 

 

the last-selected language when power is restored. The parameter

 

 

must be either COMP or TMSL, not SCPI.

 

 

 

 

66 Compatibility Language

Page 62 Page 64
Image 63
Page 62 Page 64
Contents July PROGRAMMING GUIDE GPIB DC POWER SUPPLIESAgilent Part No Microfiche Part NoPrinting History Safety GuidelinesLANGUAGE DICTIONARY ContentsGENERAL INFORMATION REMOTE PROGRAMMINGDescription of Subsystem Commands COMPATIBILITY LANGUAGE ERROR MESSAGESSTATUS REPORTING SCPI CONFORMANCE INFORMATIONUser’s Guide General InformationAbout this Guide Documentation SummaryAccessing Online Help Prerequisites for Using this GuideVXIplug&play Power Product Instrument Drivers Downloading and Installing the DriverConventions GPIB Capabilities Of The Power SupplyRemote Programming Introduction To SCPICommon Commands Types of SCPI CommandsSCPI Messages Structure of a SCPI MessageVOLT LEV PROT CURR Parts of a SCPI MessageFigure 2-1.Command Message Structure Message ComponentRoot Specifier Traversing the Command TreeQuery Indicator Message Unit SeparatorMoving Among Subsystems Figure 2-2.Partial Command TreeActive Header Path The Effect of Optional HeadersSCPI Data Formats Including Common CommandsSCPI Queries Value CouplingClass ExamplesListening Formats Table 2-2.Suffixes and MultipliersProgramming Voltage and Current Controlling the OutputDisable the output Enable the outputSaving and Recalling States Writing to the DisplayProgramming Status System Considerations Programming the Digital I/O PortThe GPIB Address A direct primary address and a secondary address Error Handling DOS DriversAgilent BASIC Controllers Sample Program CodeController Using Agilent 82335A Interface Programming Some Power Supply Functions22 Remote Programming Programming Some Power Supply Functions continued1130 24 Remote Programming Language Dictionary Related CommandsCommon Commands Subsystem CommandsFigure 3-1.Common Commands Syntax Diagram Description Of Common CommandsMeaning and Type Description0 to Query Syntax ESR?IDN? Related CommandsPSC 0 *PSC OPC?OPT? Power-onStatus Clear Device InitializationDescription Meaning and TypeDescription Bit Configuration of Status Byte Register STB?TST? Figure 3-2.Subsystem Commands Tree Diagram Description of Subsystem CommandsCalibration Commands ABORCURRENT:LEVEL 200 MA Current SubsystemCURR CURR TRIG CURR PROT STATDigital I/O Port Programming Chart Display SubsystemDIG DATA DISPenclosed in either single ‘ or double quotes DISP MODEDISP TEXT DISP TEXT DEFAULT MODEMEAS CURR? MEAS VOLT? Initiate SubsystemMeasure Subsystem INIT INIT:CONT0 or Output SubsystemOUTP OUTP PROT CLE OUTP PROT DELOUTP REL POL NORM OUTP RELOUTP REL POL OUTP REL 1 OUTP REL OFFSTAT OPER? Status SubsystemSTAT PRES Status Operation RegistersSTAT OPER ENAB STAT OPER NTR STAT OPER PTRSTATUS OPERATION ENABLE? STAT QUES ENAB Status Questionable RegistersSTAT QUES? STAT:QUES:COND?corresponding Questionable Event register System CommandsSTAT QUES NTR STAT QUES PTR SYST ERR?TRIG Trigger SubsystemSYST LANG SYST VERS?VOLTAGE LEVEL 200 MV Voltage SubsystemTRIG SOUR VOLT VOLT TRIGCommand Command SummaryVOLT:PROT Command SummaryCommand Parameters Agilent Model and Value Characteristics in the Operating GuideProgramming Parameters ParameterOperation Status Group Power Supply Status StructureRegister Commands Status ReportingMeaning Table 4-2.Bit Configurations of Status RegistersSignal Figure 4-1.Power Supply Status ModelCLS *ESR? Questionable Status GroupStandard Event Status Group Table 4-3.Status Questionable CommandsStatus Byte Register Service Request Enable RegisterInitial Conditions At Power On Determining the Cause of a Service InterruptCaused By The PON Power-OnBitServicing an Operation Status Mode Event Table 4-4.Default Power On Register StatesTable 4-5.Generating RQS from the CC Event Monitoring Both Phases of a Status TransitionAdding More Operation Events Servicing Questionable Status EventsTechniques in ANSI/IEEE Std SCPI Command CompletionDFI Discrete Fault Indicator RI Remote InhibitSystem Error Messages Error MessagesPower Supply Hardware Error Messages Calibration Error Messages60 Error Messages SCPI Version SCPI Confirmed Commands1SCPI Approved Commands SCPI Conformance InformationNON-SCPICommands1 Compatibility Language Table B-1.ARPS Commands ARPS Command1Similar SCPI Table B-1.ARPS Commands continued Description Index 68 Index Page Canada Agilent Sales and Support OfficeUnited States Latin America
Related manuals
Manual 70 pages 51.66 Kb Manual 142 pages 24.05 Kb

668xA, 669xA, 667xA, 664xA, 665xA specifications

Agilent Technologies has long been a pioneer in the production of high-performance electronic test and measurement instruments, particularly in the field of power sources. Among its notable offerings are the Agilent 667xA, 669xA, 665xA, 664xA, and 668xA series of power supplies. These instruments are designed to provide stable, reliable power for a variety of applications, including electronic testing, industrial processes, and research laboratories.

The Agilent 667xA series is characterized by its programmability and advanced measurement functions. These power supplies support a wide range of output voltages and currents, allowing for flexible configurations that cater to different testing needs. The built-in measurement capabilities enable users to monitor the voltage, current, and power with high precision, which is essential for ensuring optimal performance in electronic applications.

The Agilent 669xA series stands out with its high-power outputs, making it suitable for demanding applications. These power supplies deliver high voltage and current levels, making them ideal for testing high-performance devices, such as power amplifiers and motor drives. Additionally, the 669xA series includes features such as overvoltage protection and complex output sequencing to enhance the safety and reliability of the testing process.

The Agilent 665xA and 664xA series focus on delivering high accuracy and excellent regulation. These models are particularly known for their low noise operation, which is critical for sensitive applications where precision is paramount. The integrated programming capabilities allow users to automate testing sequences, thus improving efficiency in research and development settings.

The 668xA series features advanced digital signal processing that enhances the precision and stability of the output. Users benefit from features like remote sensing and monitoring, allowing feedback adjustments that maintain output accuracy despite cable losses. Furthermore, the 668xA models can integrate seamlessly with various test environments thanks to their LAN, GPIB, and USB connectivity options.

Overall, the Agilent 667xA, 669xA, 665xA, 664xA, and 668xA power supplies provide a comprehensive range of solutions for diverse electronic testing needs. With their advanced features, superb measurement capabilities, and robust performance, these instruments empower engineers and researchers to conduct their work with confidence, precision, and efficiency.
Top Page Image Contents