Mitsubishi Electronics FX1S Interrupt Pointers, Additional applied instructions, Nested levels

Page 85

FX Series Programmable Controllers

Devices in Detail 4

4.6Interrupt Pointers

FX1S

FX1N

FX2N

FX2NC

Device Mnemonic: I

Purpose: Interrupt program marker

Alias: Interrupt

High speed interrupt

I

Available forms: Label: appears on the left of the left hand bus bar when the program is viewed in ladder mode

(see in the example device usage diagram).

Devices numbered in: Special numbering system based on interrupt device used and input triggering method

Further uses: Input interrupts - see page 4-12

Timer interrupts - see page 4-12

Disabling interrupts - see page 4-13

Counter interrupts - see page 4-13

Example device usage:

FEND

I101

1

IRET

END

Additional applied instructions:

• Interrupts are made up of an interrupt device, an interrupt pointer and various usage of three, dedicated interrupt applied instructions;

-IRET function 03: interrupt return - see page 5-9

-EI function 04: enable interrupt - see page 5-9

-DI function 05: disable interrupt - see page 5-9

Nested levels:

While an interrupt is processing all other interrupts are disabled. To achieve nested interrupts the EI-DI instruction must be programmed within an interrupt routine. Interrupts can be nested for two levels.

Pointer position:

Interrupt pointers may only be used after an FEND instruction (first end instruction, function 06).

4-11

Image 85
Contents Programming Manual Page Foreword FX Series Programmable ControllersFX Series Programmable Controllers FAX Back Combined Programming Manual J FX Series Programmable Controllers Software Warnings Hardware WarningsFX Series Programmable Controllers Contents STL Programming Applied Instructions Rotation And Shift Functions 30 to External FX Serial Devices Functions 80 to Execution Times And Instructional 10-1 Viii FX Series Programmable Controllers Chapter Contents Overview IntroductionWhat do You Need to Program a PLC? What is a Programmable Controller?Current Generation CPU all versions Special considerations for programming equipmentManual name Number FX Base Unit Hardware Assocciated ManualsManual name Number FX DU, GOT and DM units Memo Basic Program Instructions FX Series Programmable ControllersBasic Program Instructions Outline of Basic Devices Used in Programming What is a Program?Detailed device information Example How to Read Ladder LogicOUT instruction Load, Load InverseProgram example Out Timer and Counter VariationsLast coil effect Use of dual coilsDouble Coil Designation Peripheral limitations And, And InverseORI Or, Or InverseSingle Operation flags M2800 to M3071 Load Pulse, Load Trailing PulseLDF ANF OUT Pulse, And Trailing PulseORF ORB Or Pulse, Or Trailing PulseBatch processing limitations Or BlockSequential processing limitations ANB BlockMPS, MRD and MPP usage 13 MPS, MRD and MPPMultiple program examples MCR Master Control and ResetNested MC program example Resetting timers and counters Set and ResetRetentive timers Timer, Counter Out & Reset16.1Basic Timers, Retentive Timers And Counters Availability of devices Bit countersNormal 32 bit Counters High Speed CountersLeading and Trailing Pulse PLFUsages for INV InverseNo Operation No OperationProgram scan 20 EndMemo STL Programming FX Series Programmable ControllersSTL Programming General note What is STL, SFC And IEC1131 Part 3?Each step is a program How STL OperatesLook Inside an STL Combined SFC Ladder representation How To Start And End An STL ProgramEmbedded STL programs Activating new statesTerminating an STL Program Initial StepsReturning to Standard Ladder Moving Between STL Steps Using SET to drive an STL coilOUT is used for loops and jumps Using OUT to drive an STL coilOut is used for distant jumps Basic Notes On The Behavior Of STL programs Rules and Techniques For STL programsT001 K20 K50 Method 1 Using locking devices Single Signal Step ControlMethod 2 Special Single Pulse Flags Using ‘jump’ operations with STL Restrictions Of Some Instructions When Used With STLRestrictions on using applied instructions STL OUT SET Using STL To Select The Most Appropriate ProgramLimits on the number of branches Using STL To Activate Multiple Flows SimultaneouslyLimits on the number of branches Instruction Format General Rules For Successful STL BranchingGeneral Precautions When Using The FX-PCS/AT-EE Software Simple STL Flow Programming ExamplesSET STL Identification of normally closed contactsSelective Branch/ First State Merge Example Program Points to noteFull STL flow diagram/program Advanced STL Use Devices in Detail FX Series Programmable ControllersDevices in Detail Inputs Configuration detailsAvailable devices Device MnemonicDevice Mnemonic Y OutputsAlias O/P Device Mnemonic M Auxiliary RelaysGeneral Stable State Auxiliary Relays External loads Battery Backed/ Latched Auxiliary RelaysSpecial Single Operation Pulse Relays Special Diagnostic Auxiliary RelaysDevice Mnemonic S State RelaysGeneral Stable State State Relays PLC FX 1S FX 1N FX 2N Battery Backed/ Latched State Relays Monitoring STL programs Assigned states STL/SFC programming IST instructionAnnunciator Flags Jumping to the end of the program PointersDevice availability Device Mnemonic PAdditional applied instructions Interrupt PointersNested levels Pointer positionRules of use Timer InterruptsInput Interrupts Disabling high speed counter interrupts Driving special auxiliary relaysAdditional notes Disabling Individual InterruptsConstant H Constant KDevice Mnemonic K Example device usage N/ATimer accuracy TimersDevice Mnemonic T Selectable Timers General timer operationDriving special auxiliary coils Retentive Timers Using timers in interrupt or ‘CALL’ subroutinesTimers Used in Interrupt and ‘CALL’ Subroutines Internal timer accuracyTimer Accuracy ConditionCounters Setting ranges for countersHigh speed counters Device Mnemonic CGeneral/ Latched 16bit UP Counters Battery backed/latched countersSelecting the counting direction Battery backed/ latched countersGeneral/ Latched 32bit Bi-directional Counters Further uses None Basic high speed counter operationBasic High Speed Counter Operation Driving high speed counter coilsCounter Speeds Input assignmentAvailability of High Speed Counters Calculating the maximum combined counting speed on FX1S Setting range Device specificationDirection setting Using the SPD instructionRST Device size 11.5 2 Phase Bi-directional Counters C246 to C25011.6 A/B Phase Counters C252 to C255 Device Mnemonic D Data RegistersExample device usage None Data retention Data register updatesGeneral Use Registers Use of diagnostic registers Using the FX2-40AW/APBattery Backed/ Latched Registers Special Diagnostic RegistersWriting to file registers Special caution when using FX1SFile Registers Program memory registersUses Externally Adjusted RegistersUse of Modifiers with Applied Instruction Parameters Index RegistersDevice Mnemonic V,Z Available formsModifying a Constant Using Multiple Index RegistersMisuse of the Modifiers Bit Devices, Individual and Grouped Bits, Words, BCD and HexadecimalAssigning I/O Moving grouped bit devicesAssigning grouped bit devices Interpreting Word Data Word DevicesFX Series Programmable Controllers Word Data Summary Binary Coded Decimal value= ErrorInverted7 Additional1 14.4 Two’s ComplimentSome useful constants Floating Point And Scientific NotationScientific Notation Floating Point Format FLT