Southbend sb1018 owner manual Machine Labels, PSBLABEL15S Electricity Label

Page 54

Model SB1018

P A R T S

For Machines Mfg. Since 8/09

Machine Labels

508	507	506	505
508

504

509510

503

513

511	512

501

502

REF	PART #	DESCRIPTION
501	PSB1018501	MACHINE ID LABEL
502	PSB1018502	MODEL NUMBER LABEL
503	PSBLABEL15S	ELECTRICITY LABEL
504	PSB1017304	BELT COVER WARNING LABEL
505	PSBLABEL02HS	DISCONNECT WARNING LABEL
506	PSB1017306	CUTTING HAZARD WARNING LABEL
507	PSBLABEL04HS	EYE INJURY WARNING LABEL

REF	PART #	DESCRIPTION
508	PSBLABEL01HS	READ MANUAL LABEL
509	PSBLABEL13VS	DOOR CLOSED WARNING LABEL
510	PSBPAINT01	SB LT GRAY TOUCH-UP PAINT
511	PSBPAINT03	SB DK BLUE TOUCH-UP PAINT
512	SB1320	SOUTH BEND NAMEPLATE 125MM
513	PSBPAINT02	SB LT BLUE TOUCH-UP PAINT

The safety labels provided with your machine are used to make the operator aware of the machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of these safety labels. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact South Bend Lathe Co. at (360) 734-1540 or www.southbendlathe.com to order new labels.

-52-

Image 54

Contents 6 Swivel Mast Bandsaw Scope of Manual UpdatesCustomer Service Manual FeedbackTable of Contents Features About This MachineCapabilities Identification IdentificationMachine Specifications Machine SpecificationsOther Basic Machine Safety Understanding Risks of MachineryF E T Y Additional Metal Bandsaw Safety Availability Power Supply RequirementsThings Youll Need Full-Load Current RatingCircuit Requirements for For 110V Connection PrewiredCircuit Information Grounding RequirementsUnpacking InventoryExtension Cords Description Qty Cleaning & Protecting Before cleaning, gather the followingBasic steps for removing rust preventative Location Assembly To assemble the bandsawLoosen the belt tension bolt shown in Figure Installing belt Power Connection Removing shipping strapInspections Adjustments Test RunTo test run your machine OperationPERATIONOverview Description of Controls & Components Blade Length Blade SelectionBlade Terminology Blade WidthTooth Set Tooth TypeBlade Pitch TPI To select the correct blade pitchBlade Changes To change the blade on the bandsawTo tension the blade on the bandsaw Blade TensionBlade Breakage Most common causes of avoidable blade breakage areBlade Care Blade Care & Break-InBlade Speed Blade Break-InBlade Speed Chart Chip Inspection ChartDownfeed Rate Angle CutsCuts to the Right Vise Cuts to the LeftBlade Guide To adjust the blade guideWork Stop Operation TipsCleaning LubricationMachine Storage GearboxTo change the gearbox oil To adjust the blade tracking on the bandsaw Blade TrackingSquaring Blade To adjust the blade guide bearingsBlade Guide Bearings To square the blade to the tablePulley Deflection BeltTo tighten the V-belt To replace the V-beltTo adjust the downfeed stop bolt and OFF button lever Downfeed StopModel SB1018TROUBLESHOOTI NG For Machines Mfg. Since 8/09 Troubleshooti NG Troubleshooti NG ElectricalL CTRICALSafety Instructions Wiring Diagram Color KEY220V Conversion To convert the Model SB1018 toWiring Diagram Wiring Component Locations Wiring component locationsBase & Cabinet Stand Base & Cabinet Stand Parts List DescriptionHead & Vise Head & Vise Parts List Motor & Blade Guides Motor & Blade Guides Parts List Switch Machine Labels PSBLABEL15S Electricity LabelR R a N T Y Southbendlathe.com