Southbend sb1018 owner manual Test Run, Inspections Adjustments, To test run your machine

Page 21

For Machines Mfg. Since 8/09

P R E P A R A T I O N

Model SB1018

Test Run

After all preparation steps have been completed, the machine and its safety features must be tested to ensure correct operation. If you discover a problem with the operation of the machine or its safety components, do not operate it further until you have resolved the problem.

Note: Refer to Troubleshooting on Page 38 for solutions to common problems that may occur with metal-cutting bandsaws. If you need additional help, contact our Tech Support at (360) 734-1540.

To test run your machine:

1.Read and follow the safety instructions at the beginning of the manual, take the re- quired safety precautions, and make sure the machine is set up properly.

2.Clear away all tools and objects used during assembly and preparation.

3.Open the downfeed valve (Figure 23) and allow the headstock to travel all the way down. If the blade contacts the machine base, adjust the downfeed stop bolt as described in Downfeed Stop Bolt, on Page 37.

Downfeed

Valve

Figure 23. Downfeed valve location.

4.Connect the machine to the power source.

5.Put on safety glasses and secure loose clothing or long hair.

6.Lift the headstock by the handle to the raised position, then close the downfeed valve to prevent it from lowering.

7.Start the bandsaw while keeping your finger near the ON/OFF switch at all times during the test run. The bandsaw should run smoothly with little or no vibration.

If you suspect any problems, immediately turn the bandsaw OFF, disconnect it from power, and correct the problem before continuing.

If you need any help with your bandsaw call our Tech Support at (360) 734-1540.

8.Open the downfeed valve to lower the saw through its full range of motion. When it reaches the bottom of its travel, it should turn OFF. If it does not, manually turn it OFF, disconnect it from power, then re- adjust the auto-OFF lever, by performing Steps 36on Page 37.

Inspections &

Adjustments

The following list of adjustments were performed at the factory before your machine was shipped. If you find that the adjustments are not set according to the procedures in this manual or your personal preferences, re-adjust them.

Blade Tracking ...................................Page 34

Squaring the Blade ............................Page 35

Blade Guide Bearings ........................Page 35

-19-

Image 21
Contents 6 Swivel Mast Bandsaw Customer Service UpdatesScope of Manual Manual FeedbackTable of Contents Features About This MachineCapabilities Identification IdentificationMachine Specifications Machine SpecificationsOther Understanding Risks of Machinery Basic Machine SafetyF E T Y Additional Metal Bandsaw Safety Things Youll Need Power Supply RequirementsAvailability Full-Load Current RatingCircuit Information For 110V Connection PrewiredCircuit Requirements for Grounding RequirementsUnpacking InventoryExtension Cords Description Qty Cleaning & Protecting Before cleaning, gather the followingBasic steps for removing rust preventative Location To assemble the bandsaw AssemblyLoosen the belt tension bolt shown in Figure Installing belt Removing shipping strap Power ConnectionInspections Adjustments Test RunTo test run your machine OperationPERATIONOverview Description of Controls & Components Blade Terminology Blade SelectionBlade Length Blade WidthTooth Type Tooth SetTo select the correct blade pitch Blade Pitch TPITo change the blade on the bandsaw Blade ChangesBlade Breakage Blade TensionTo tension the blade on the bandsaw Most common causes of avoidable blade breakage areBlade Speed Blade Care & Break-InBlade Care Blade Break-InChip Inspection Chart Blade Speed ChartDownfeed Rate Angle CutsCuts to the Right Cuts to the Left ViseWork Stop To adjust the blade guideBlade Guide Operation TipsLubrication CleaningMachine Storage GearboxTo change the gearbox oil Blade Tracking To adjust the blade tracking on the bandsawBlade Guide Bearings To adjust the blade guide bearingsSquaring Blade To square the blade to the tableTo tighten the V-belt BeltPulley Deflection To replace the V-beltDownfeed Stop To adjust the downfeed stop bolt and OFF button leverModel SB1018TROUBLESHOOTI NG For Machines Mfg. Since 8/09 Troubleshooti NG Troubleshooti NG Wiring Diagram Color KEY ElectricalL CTRICALSafety InstructionsTo convert the Model SB1018 to 220V ConversionWiring Diagram Wiring component locations Wiring Component LocationsBase & Cabinet Stand Description Base & Cabinet Stand Parts ListHead & Vise Head & Vise Parts List Motor & Blade Guides Motor & Blade Guides Parts List Switch PSBLABEL15S Electricity Label Machine LabelsR R a N T Y Southbendlathe.com