Grizzly G0456 owner manual Inventory Components Figure Qty, Hardware not shown Qty

Page 13

Inventory

After all the parts have been removed from the crate, you should have the following items:

Inventory Components (Figure 3)

 

Qty

A.

Lathe Bed (not shown)

1

B.

Stand Assembly (not shown)

1

C.

Sanding Table

1

D.

L-Brackets

2

E.

Tool Rest

1

F.

Spur Center

1

G.

Live Center

1

H.

Flat Wrench 11316"

1

I.

Lock Pin

1

J.

Dust Port

1

K.

Lock Handles

2

L.

Miter Gauge

1

Hardware (not shown)

 

Qty

Hex Bolts 716"-14 x 34" (L-Brackets)

4

Flat Washers 716" (L-Brackets)

4

Lock Washers 716" (L-Brackets, Bed)

10

Flat Washers 14" (Handles)

4

Cap Screws 516"-18 x 58" (Table)

2

Lock Nuts 516"-18 (Table)

2

Flat Washers 516" (Table)

2

Phillips Screws 10-24 x 12" (Dust Port)

...... 2

Lock Washers #10 (Dust Port)

2

Cap Screws 716"-14 x 112" (Bed)

6

Hex Wrench 4, 5, 6, 8mm

1 Each

Open End Wrench 10/12mm

1

G0456 Variable Speed Wood Lathe

 

 

 

 

 

 

Figure 3. Model G0456 inventory components.

In the event that any nonproprietary parts are missing (e.g. a nut or a washer), we would be glad to replace them, or for the sake of expedi- ency, replacements can be obtained at your local hardware store.

SUFFOCATION HAZARD!

Immediately discard all plastic bags and packing materials to eliminate choking/suffocation hazards for children and animals.

-11-

Image 13
Contents Model G0456 Variable Speed Wood Lathe Page Table of Contents Warranty and Returns Foreword IntroductionContact Info Machine Data Sheet Identification Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Wood Lathes Circuit Requirements 220V Single-PhaseSet Up Safety SET UPItems Needed for Set Up UnpackingInventory Components Figure Qty InventoryHardware not shown Qty Site Considerations Clean UpComponents and Hardware Needed Qty Mounting LatheTo mount the lathe bed To install the tool rest To install the sanding tableSanding Table Tool RestTo connect a dust collection hose Dust Collection Test RunTo test run the machine Operations Operation Safety Safety KeyControls To position the tailstock along the bed Adjusting Tailstock Adjusting Tool RestTo position the tool rest along the bed To install the centers Installing/Removing Spur CenterTo remove the spur center To install the live center Installing/Removing Live CenterTo remove the live center Gouge Selecting Turning ToolsSpindle Turning To set up a spindle turning operationTo mount your workpiece to the faceplate Faceplate TurningSanding/Finishing Changing SpeedsTo mount your workpiece to a backing block To change between High and Low speedsDisc Sanding Attaching SandpaperTo attach sandpaper To perform sanding operationsAngle Sanding Miter SandingTo perform miter sanding operations To perform angle sanding operationsG1194-3-Jaw Chuck AccessoriesG1082-4-Jaw Chuck G3168-1-1⁄2 x 8 TPI RH Threaded InsertG9863-8-PC HSS Lathe Chisel Set Model H6542 Robert Sorby 8-PC SetModel Grit PSA Sanding Discs 2 pkH1300 H1298 G7984 H2347 H0736 Cleaning/Lubricating MaintenanceTroubleshooting ServiceWood Lathe Operation To check headstock/tailstock alignment Tools Needed QtyTo align the headstock with the tailstock To change the V-belt Replacing or Tightening V-BeltTo replace the motor brushes Replacing Motor BrushesTable Tilt To adjust table tiltAligning Table To align the tableMiter Gauge To adjust miter gaugeElectrical Components Wiring Diagram Parts Breakdown Description Parts ListDescription Warranty and Returns Page Page