Grizzly G0456 owner manual Accessories, G1194-3-Jaw Chuck, G1082-4-Jaw Chuck

Page 28

ACCESSORIES

SECTION 5: ACCESSORIES

G1194—3-Jaw Chuck

A "must have" for the serious wood turner. This 3-jaw chuck is a self-centering style chuck used mostly for round work. All three jaws tighten together at the same time. Jaws are reversible for expanded work holding capacity. Threaded insert required for mounting!

Figure 34. Model G1194 3-Jaw Chuck.

G1082—4-Jaw Chuck

Another "must have" for the serious wood turner. This 4-jaw chuck is an independent type chuck that is used for square and odd-shaped pieces. Each jaw tightens individually and can be turned around to hold larger dimension workpieces. Threaded insert required for mounting!

G3168—1-12" x 8 TPI RH Threaded Insert

This threaded insert is required to mount a 3- or 4-jaw chuck to your wood lathe.

H1064—6-PC Deluxe HSS Lathe Chisel Set This deluxe chisel set features beefy ash han- dles for unsurpassed control, brass ferrules and high speed steel blades. Includes: a 17" long

1316" Parting Tool, 1316" Round Nose and 38" Gouge; a 19" long 1" Skew, a 58" Gouge and a

2234" long 38" Gouge. Comes in a beautiful blow molded carrying case. An extremely popular set!

Figure 36. Model H1064 6-PC Chisel Set.

Figure 35. Model G1082 4-Jaw Chuck.

-26-

G0456 Variable Speed Wood Lathe

Image 28
Contents Model G0456 Variable Speed Wood Lathe Page Table of Contents Warranty and Returns Foreword IntroductionContact Info Machine Data Sheet Identification Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Wood Lathes 220V Single-Phase Circuit RequirementsSET UP Set Up SafetyItems Needed for Set Up UnpackingInventory Components Figure Qty InventoryHardware not shown Qty Clean Up Site ConsiderationsComponents and Hardware Needed Qty Mounting LatheTo mount the lathe bed To install the sanding table To install the tool restSanding Table Tool RestTo connect a dust collection hose Dust Collection Test RunTo test run the machine Operations Operation Safety Safety KeyControls To position the tailstock along the bed Adjusting Tailstock Adjusting Tool RestTo position the tool rest along the bed To install the centers Installing/Removing Spur CenterTo remove the spur center To install the live center Installing/Removing Live CenterTo remove the live center Selecting Turning Tools GougeTo set up a spindle turning operation Spindle TurningFaceplate Turning To mount your workpiece to the faceplateChanging Speeds Sanding/FinishingTo mount your workpiece to a backing block To change between High and Low speedsAttaching Sandpaper Disc SandingTo attach sandpaper To perform sanding operationsMiter Sanding Angle SandingTo perform miter sanding operations To perform angle sanding operationsAccessories G1194-3-Jaw ChuckG1082-4-Jaw Chuck G3168-1-1⁄2 x 8 TPI RH Threaded InsertModel H6542 Robert Sorby 8-PC Set G9863-8-PC HSS Lathe Chisel SetModel Grit PSA Sanding Discs 2 pkH1300 H1298 G7984 H2347 H0736 Maintenance Cleaning/LubricatingService TroubleshootingWood Lathe Operation To check headstock/tailstock alignment Tools Needed QtyTo align the headstock with the tailstock Replacing or Tightening V-Belt To change the V-beltReplacing Motor Brushes To replace the motor brushesTo adjust table tilt Table TiltAligning Table To align the tableTo adjust miter gauge Miter GaugeElectrical Components Wiring Diagram Parts Breakdown Parts List DescriptionDescription Warranty and Returns Page Page