Grizzly G0456 owner manual Model H6542 Robert Sorby 8-PC Set, G9863-8-PC HSS Lathe Chisel Set

Page 29

H6542—Robert Sorby HSS 8-PC Turning Set If quality is king, then start bowing. Made in England, these Robert Sorby lathe tools are espe- cially for the perfectionist wood turner. Includes

3⁄4" roughing gouge, 3⁄8" & 1⁄2" spindle gouge, 3⁄8" bowl gouge, 3⁄4" standard skew, 3⁄16" diamond side cut scraper, 1" square scraper and 1⁄2" round scraper. Full size handles are 16"–19".

Figure 37. Model H6542 Robert Sorby 8-PC Set.

G9863—8-PC HSS Lathe Chisel Set

This chisel set features beautiful 8" ash handles with brass ferrules and 31⁄2" long, high speed steel blades. Chisels include: 1⁄2" parting tool,

1⁄2" straight chisel, 1⁄2" double bevel skew, 1⁄2" roundnose, 3⁄4" gouge, 3⁄8" gouge, 1⁄2" diamond point and 3⁄8" veiner. Set comes in fitted wooden case, and is very competitively priced!

Figure 38. Model G9863 8-PC Chisel Set.

H6204—Precision Drill Chuck 1⁄32"–5⁄8" x JT#3 G1676—Drill Chuck Arbor MT#2 x JT#3

The best way to bore holes with your lathe!

G0456 Variable Speed Wood Lathe

H0507—20" Swan Neck Hollowing Tool H0508—24" Swan Neck Hollowing Tool

An excellent choice for blind turning or undercut- ting where reach is restricted. H0507 is designed for end grain use while H0508 (with a more sub- stantial steel cross section) is designed for both end grain and side grain (bowl) use.

Figure 39. Swan Neck Hollowing Tools.

H5954—Robert Sorby Stebcentre MT#2 Razor sharp teeth bite into the workpiece for secure operation and the spring loaded center point controls the amount of drive or slip. This pat- ented feature helps avoid the problem of "dig-in." A great addition for production wood turners.

Figure 40. Robert Sorby Stebcentre.

-27-

Image 29

Contents Model G0456 Variable Speed Wood Lathe Page Table of Contents Warranty and Returns Contact Info IntroductionForeword Machine Data Sheet Identification Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Wood Lathes Circuit Requirements 220V Single-PhaseSet Up Safety SET UPItems Needed for Set Up UnpackingHardware not shown Qty InventoryInventory Components Figure Qty Site Considerations Clean UpTo mount the lathe bed Mounting LatheComponents and Hardware Needed Qty To install the tool rest To install the sanding tableSanding Table Tool RestTo test run the machine Dust Collection Test RunTo connect a dust collection hose Controls Operation Safety Safety KeyOperations To position the tool rest along the bed Adjusting Tailstock Adjusting Tool RestTo position the tailstock along the bed To remove the spur center Installing/Removing Spur CenterTo install the centers To remove the live center Installing/Removing Live CenterTo install the live center Gouge Selecting Turning ToolsSpindle Turning To set up a spindle turning operationTo mount your workpiece to the faceplate Faceplate TurningSanding/Finishing Changing SpeedsTo mount your workpiece to a backing block To change between High and Low speedsDisc Sanding Attaching SandpaperTo attach sandpaper To perform sanding operationsAngle Sanding Miter SandingTo perform miter sanding operations To perform angle sanding operationsG1194-3-Jaw Chuck AccessoriesG1082-4-Jaw Chuck G3168-1-1⁄2 x 8 TPI RH Threaded InsertG9863-8-PC HSS Lathe Chisel Set Model H6542 Robert Sorby 8-PC SetH1300 H1298 G7984 H2347 H0736 PSA Sanding Discs 2 pkModel Grit Cleaning/Lubricating MaintenanceTroubleshooting ServiceWood Lathe Operation To align the headstock with the tailstock Tools Needed QtyTo check headstock/tailstock alignment To change the V-belt Replacing or Tightening V-BeltTo replace the motor brushes Replacing Motor BrushesTable Tilt To adjust table tiltAligning Table To align the tableMiter Gauge To adjust miter gaugeElectrical Components Wiring Diagram Parts Breakdown Description Parts ListDescription Warranty and Returns Page Page