Carrier ZONEKIT4ZCAR ÐExample Weekly Schedule, Controller Display, Zone Selector Dial

Page 15

Cool Switch

OFFÐCooling will not come on.

AUTOÐCooling will come on when any zone is more than 1.5°F above desired cool setpoint.

Fan Switch

ONÐFan will stay on continuously (recommended).

AUTOÐFan will come on only when heating or cooling is required.

Emergency Heat Switch (Heat Pump Systems only)

OFFÐElectric strip heat will not come on unless there is a zone more than 2°F below desired heat setpoint and comfort trend demand has been satisfied.

ONÐWhen any zone requires heat, electric strip heat will turn on. The compressor will remain off.

CONTROLLER DISPLAY

When set for normal operation, the 4 zone controller display shows current zone temperature setpoints and allows adjustment of these setpoints using setpoint buttons. By pressing both heating or cooling setpoint buttons simultaneously, controller will lock in and display temperatures for that zone. To release, push both buttons simultaneously again. This will only work when T-20 is off.

ZONE SELECTOR DIAL

To view setpoints for each zone, turn zone selector dial to zone number you wish to view.

The setpoints for selected zone will be displayed in controller display.

Program Schedules

Each zone has 3 different weekly periods, (Weekdays, Saturday, and Sunday) and up to 4 different possible combinations of heating and cooling setpoints that can be programmed to provide auto- matic climate control depending upon day of week and time of each day. Each zone can be programmed independently. (See Table 9.)

NOTE: All zones must be programmed.

Table 9ÐExample Weekly Schedule

WEEKDAYS

SATURDAY

SUNDAY

6 AM

72/70

 

7 AM

72/68

8 AM

72/70

8 AM

85/65

 

10 AM

85/65

10 AM

85/65

5 PM

70/68

 

2 PM

70/68

7 PM

70/68

10 PM

85/65

 

11 PM

85/65

10 PM

85/65

 

 

 

 

 

 

 

 

 

 

WEEKLY PERIOD

 

 

Start Time

 

Cooling Setpoint/Heating Setpoint

Vacation Mode

Vacation mode displays current vacation temperature setpoints and allows adjustment of these setpoints using setpoint buttons. These setpoints are used by all zones until selector dial is returned to 1 of the zone selection positions. At all times, the setpoints displayed will be the temperature range that the system will maintain.

This mode can also be used to maintain entire home at 1 constant temperature-typically when unoccupied.

NOTE: If Fan Switch is set to ON, fan will continue to run in vacation mode.

To enter vacation mode, turn selector dial to VACATION. The word "VACATION" will appear on controller display whenever system is in this mode. Set vacation mode setpoints.

Setting The Clock

The clock display will normally show hour, minutes, AM or PM, and day.

1.Set minutes.

Press SELECT MIN/HR/DAY button once.

Press ADVANCE TIME/DAY button to scroll to proper minutes.

2.Set hour.

Press SELECT MIN/HR/DAY button once again.

Press ADVANCE TIME/DAY button to scroll to proper hour, AM or PM.

3.Set day.

Press SELECT MIN/HR/DAY button once again.

Press ADVANCE TIME/DAY button to scroll to proper day.

4.Return to normal operation.

Press SELECT MIN/HR/DAY button once again. The newly programmed time will be displayed.

Programming Schedules

1.Enter Program Mode

Press SET TIME/TEMP SCHEDULES button to enter pro- gram mode. The program mode and current zone will be shown on controller display.

2.Select a zone.

Turn rotary switch to the zone to be programmed.

3.Select a weekly period.

The clock display will show MTWTHF.

Pressing ADVANCE TIME/DAY button selects weekly pe- riod to be programmed.

Pressing button 1 time will change clock display to SA. A second press will change display to SU.

A third press returns display to MTWTHF.

4.Program time periods.

There are 4 start times that can be programmed in each weekly period.

Press SELECT MIN/HR/DAY button to program start times for selected weekly period.

Pressing SELECT MIN/DAY/HR button once shows first program start time on clock display and setpoints, with the word PROGRAM for this start time on controller display.

Additional presses display start times 2, 3, 4, and then back to weekly period display.

NOTE: While in program mode, if a period of 4-1/2 minutes passes without a change to some value, the controller will return to normal operation.

5. Program start time

NOTE: Start times must be programmed in chronological order and must be in the same day. Any times before previous time period will be ignored. In the WRONG example below, periods 2 and 4 will be ignored.

RIGHT

6

AM - TIME PERIOD 1

 

8

AM - TIME PERIOD 2

 

5

PM - TIME PERIOD 3

 

9

PM - TIME PERIOD 4

WRONG

6

AM - TIME PERIOD 1

 

2

AM - TIME PERIOD 2

 

9

PM - TIME PERIOD 3

 

5

PM - TIME PERIOD 4

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents ZONEKIT4ZCAR ÐWiring ÐCheck Equipment and JobsiteShielded Cable From MAX Comfort Zone Gage Length Wires Center to ÐWiring RequirementsÐInstall Comfort Zone Center ÐInstall Zone DampersDamper Mounting Bracket Round Metal Duct WorkRectangular Metal Duct Work Round Flexible Duct WorkRectangular Fibrous Glass Duct Work ÐInstall Barometric Bypass DamperÐInstall Duct Temperature Sensor ÐRound Flexible Duct WorkÐSequence of Operation ÐInstall Dx Coil SensorÐInstall Four Zone Controller ÐInstall Remote Room Sensors or Smart Sensors OptionalÐComfort Zone System Wiring Diagram Sequence of Events for a Normal Heating or Cooling Cycle Selection of a Reference Zone in the SystemPRE-POSITIONING Dampers and Starting the System FAN Control Strategy for Heating / Cooling Stages ÐZone Damper Positions Damper Position Versus Zone DemandControlling the Zone Dampers Operating the Heating and Cooling EquipmentRelay Pack to Hvac Equipment Connections Configuration Options for Equipment OperationÐHeating System Option Vs. Type of Heater Used ÐAvailable Heating and Cooling Stages Vs. System TypeÐhvac Equipment Stages Vs. Zone Demand Stage Control During Equipment OperationHeating & Cooling Demand F Demand C Equipment Stages ÐProgrammable Options-Settings ÐConfiguring Four Zone ControllerProgrammable OPTIONS-SETTINGS ÐStart-Up ÐWiring Diagram Reference ForÐWiring Diagrams Programmable OPTIONS-TOGGLESÐProgramming Schedules System SwitchesRight AM Time Period PM Time Period Wrong ÐExample Weekly ScheduleController Display Zone Selector DialSmart Sensor and Smart Sensor Power Pack ÐTemperature Sensor CalibrationsÐAccessories Home Access ModuleÐTroubleshooting Outside AIR Temperature SensorÐToggle Summary Toggle Setting OFF DefaultSymptom Possible Cause ÐOperating ProblemsSF Error Code Description Solution HF Error Code Description Solution ÐTypical Wiring Diagrams Fan Coil with Air Conditioner Comfort Zone Center Speed AIR Conditioner ÐTypical Wiring Diagrams Furnace with Air Conditioner A94037 ÐTypical Wiring Diagrams Furnace with Air Conditioner ÐTypical Wiring Diagrams Fan Coil with Heat Pump A94044 ÐTypical Wiring Diagram Furnace with Heat Pump ÐTypical Wiring Diagrams Furnace with Heat Pump ÐTypical Wiring Diagrams Furnace with Heat Pump Rotary Comfort Zone Configuration TableToggle Description Factory Record Default JOB Setting Setting

ZONEKIT4ZCAR specifications

The Carrier ZONEKIT4ZCAR is an innovative zoning system designed to enhance the comfort and efficiency of heating and cooling in residential and commercial spaces. Its functionality allows users to customize temperature settings in different areas of a building, which is especially valuable in larger homes or multi-room facilities.

One of the standout features of the ZONEKIT4ZCAR is its integration with Carrier’s advanced HVAC technology. This zoning system utilizes dampers that control airflow, directing heated or cooled air to specific areas as needed. This ensures that every room is maintained at the desired temperature without wasting energy on unused spaces. The system can effectively manage up to four different zones simultaneously.

The ZONEKIT4ZCAR is equipped with smart technology compatibility, allowing seamless integration with smart home systems. Users can control their zoning settings through mobile applications, voice commands, or smart thermostats. This feature enhances user convenience, providing access to temperature adjustments from anywhere in the home. Additionally, the system can be programmed to follow user schedules, optimizing energy usage and potentially lowering energy bills.

Another key characteristic of the Carrier ZONEKIT4ZCAR is its reliability and durability. Carrier is a well-respected brand in the HVAC industry, associated with high-quality products that are built to last. The ZONEKIT4ZCAR reflects this commitment, featuring robust construction and materials that ensure longevity and consistent performance.

The installation process of the ZONEKIT4ZCAR is designed to be straightforward, making it an appealing choice for both professionals and DIY enthusiasts. It is compatible with various Carrier heating and cooling systems, allowing for easy upgrades or replacements in existing setups.

In terms of energy efficiency, the ZONEKIT4ZCAR caters to environmentally conscious users. By allowing precise control over the climate in specific areas, the system reduces overall energy consumption, thereby lowering carbon footprints.

Finally, the ZONEKIT4ZCAR provides exceptional comfort and control, making it a smart investment for anyone looking to improve their indoor climate experience. With its combination of cutting-edge technology, user-friendly features, and energy efficiency, the Carrier ZONEKIT4ZCAR stands out in the HVAC market as a reliable choice for modern zoning solutions.
Top Page Image Contents