Carrier ZONEKIT4ZCAR instruction manual HF Error Code Description Solution

Page 21

Table 14ÐHardware Failure Errors

Error Display (Dial Position T4) must be turned on.

HF ERROR CODE

DESCRIPTION

 

SOLUTION

40

 

Bad sensor, shorted or open.

Zone 1 Temperature Sensor

1. Check wiring and sensor.

 

 

2.

Replace failed sensor, if necessary. Valid temperature range = 30°Ð180°F.

41

 

Bad sensor, shorted or open.

Zone 2 Temperature Sensor

1. Check wiring and sensor.

 

 

2.

Replace failed sensor, if necessary. Valid temperature range = 30°Ð180°F.

42

 

Bad sensor, shorted or open.

Zone 3 Temperature Sensor

1. Check wiring and sensor.

 

 

2.

Replace failed sensor, if necessary. Valid temperature range = 30°Ð180°F.

43

 

Bad sensor, shorted or open.

Zone 4 Temperature Sensor

1. Check wiring and sensor.

 

 

2.

Replace failed sensor, if necessary. Valid temperature range = 30°Ð180°F.

44

 

Bad sensor, shorted or open.

Duct Temperature Sensor

1. Check wiring and sensor.

 

 

2.

Replace failed sensor, if necessary. Valid temperature range = 30°Ð180°F.

45

 

Bad sensor, shorted or open.

Outside Air Temperature Sensor

1. Check wiring and sensor.

 

 

2.

Replace failed sensor, if necessary. Valid temperature range = -30°Ð120°F.

46

 

Bad sensor, shorted or open.

Dx Coil Sensor

1. Check wiring and sensor.

 

 

2.

Replace failed sensor, if necessary. Valid temperature range = 30°Ð180°F.

47

 

Controller can not communicate on bus.

Bus Access Error

1. Check 3-wire bus between controller and comfort zone center.

 

 

2.

Replace faulty controller/center boards, if necessary

 

 

Cannot communicate with zone 2 smart sensor.

48

 

1.

Turn toggle 13 off if there is no smart sensor attached to zone 2.

Zone 2 Smart Sensor

2. Check wiring between sensor and comfort center.

 

 

3.

Verify correct address.

 

 

4.

Must be addressed 1 less than 4 zone controller's address.

 

 

Cannot communicate with zone 3 smart sensor.

49

 

1.

Turn toggle 14 off if there is no smart sensor attached to zone 3.

Zone 3 Smart Sensor

2. Check wiring between sensor and comfort center.

 

 

3.

Verify correct address.

 

 

4.

Must be addressed 2 less than 4 zone controller's address.

 

 

Cannot communicate with zone 4 smart sensor.

50

 

1.

Turn toggle 15 off if there is no smart sensor attached to zone 4.

Zone 4 Smart Sensor

2. Check wiring between sensor and comfort center.

 

 

3.

Verify correct address.

 

 

4.

Must be addressed 3 less than 4 zone controller's address.

51

Clock Not Ready

No correction possible.

52

Parker Custom Chip Not Ready

No correction possible. Fatal error.

53

Non-Volatile RAM Not Ready

No correction possible. Fatal error.

 

 

 

 

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents ZONEKIT4ZCAR ÐWiring ÐCheck Equipment and JobsiteShielded Cable ÐInstall Comfort Zone Center ÐWiring RequirementsÐInstall Zone Dampers From MAX Comfort Zone Gage Length Wires Center toRectangular Metal Duct Work Round Metal Duct WorkRound Flexible Duct Work Damper Mounting BracketÐInstall Duct Temperature Sensor ÐInstall Barometric Bypass DamperÐRound Flexible Duct Work Rectangular Fibrous Glass Duct WorkÐInstall Four Zone Controller ÐInstall Dx Coil SensorÐInstall Remote Room Sensors or Smart Sensors Optional ÐSequence of OperationÐComfort Zone System Wiring Diagram Sequence of Events for a Normal Heating or Cooling Cycle Selection of a Reference Zone in the SystemPRE-POSITIONING Dampers and Starting the System FAN Controlling the Zone Dampers ÐZone Damper Positions Damper Position Versus Zone DemandOperating the Heating and Cooling Equipment Control Strategy for Heating / Cooling StagesÐHeating System Option Vs. Type of Heater Used Configuration Options for Equipment OperationÐAvailable Heating and Cooling Stages Vs. System Type Relay Pack to Hvac Equipment ConnectionsÐhvac Equipment Stages Vs. Zone Demand Stage Control During Equipment OperationHeating & Cooling Demand F Demand C Equipment Stages ÐProgrammable Options-Settings ÐConfiguring Four Zone ControllerProgrammable OPTIONS-SETTINGS ÐWiring Diagrams ÐWiring Diagram Reference ForProgrammable OPTIONS-TOGGLES ÐStart-UpÐProgramming Schedules System SwitchesController Display ÐExample Weekly ScheduleZone Selector Dial Right AM Time Period PM Time Period WrongÐAccessories ÐTemperature Sensor CalibrationsHome Access Module Smart Sensor and Smart Sensor Power PackÐTroubleshooting Outside AIR Temperature SensorÐToggle Summary Toggle Setting OFF DefaultSymptom Possible Cause ÐOperating ProblemsSF Error Code Description Solution HF Error Code Description Solution ÐTypical Wiring Diagrams Fan Coil with Air Conditioner Comfort Zone Center Speed AIR Conditioner ÐTypical Wiring Diagrams Furnace with Air Conditioner A94037 ÐTypical Wiring Diagrams Furnace with Air Conditioner ÐTypical Wiring Diagrams Fan Coil with Heat Pump A94044 ÐTypical Wiring Diagram Furnace with Heat Pump ÐTypical Wiring Diagrams Furnace with Heat Pump ÐTypical Wiring Diagrams Furnace with Heat Pump Toggle Description Factory Record Default JOB Setting Comfort Zone Configuration TableSetting Rotary

ZONEKIT4ZCAR specifications

The Carrier ZONEKIT4ZCAR is an innovative zoning system designed to enhance the comfort and efficiency of heating and cooling in residential and commercial spaces. Its functionality allows users to customize temperature settings in different areas of a building, which is especially valuable in larger homes or multi-room facilities.

One of the standout features of the ZONEKIT4ZCAR is its integration with Carrier’s advanced HVAC technology. This zoning system utilizes dampers that control airflow, directing heated or cooled air to specific areas as needed. This ensures that every room is maintained at the desired temperature without wasting energy on unused spaces. The system can effectively manage up to four different zones simultaneously.

The ZONEKIT4ZCAR is equipped with smart technology compatibility, allowing seamless integration with smart home systems. Users can control their zoning settings through mobile applications, voice commands, or smart thermostats. This feature enhances user convenience, providing access to temperature adjustments from anywhere in the home. Additionally, the system can be programmed to follow user schedules, optimizing energy usage and potentially lowering energy bills.

Another key characteristic of the Carrier ZONEKIT4ZCAR is its reliability and durability. Carrier is a well-respected brand in the HVAC industry, associated with high-quality products that are built to last. The ZONEKIT4ZCAR reflects this commitment, featuring robust construction and materials that ensure longevity and consistent performance.

The installation process of the ZONEKIT4ZCAR is designed to be straightforward, making it an appealing choice for both professionals and DIY enthusiasts. It is compatible with various Carrier heating and cooling systems, allowing for easy upgrades or replacements in existing setups.

In terms of energy efficiency, the ZONEKIT4ZCAR caters to environmentally conscious users. By allowing precise control over the climate in specific areas, the system reduces overall energy consumption, thereby lowering carbon footprints.

Finally, the ZONEKIT4ZCAR provides exceptional comfort and control, making it a smart investment for anyone looking to improve their indoor climate experience. With its combination of cutting-edge technology, user-friendly features, and energy efficiency, the Carrier ZONEKIT4ZCAR stands out in the HVAC market as a reliable choice for modern zoning solutions.
Top Page Image Contents