DeWalt 36-600 instruction manual Extension Cords, Minimum Gauge Extension Cord

Page 5

EXTENSION CORDS

Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grounding type plug and a 3-hole receptacle which will accept the tool’s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the saw. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. DD, shows the correct gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC TOOLS

Ampere

Volts

Total Length of

Gauge of

Rating

 

Cord in Feet

Extension Cord

0-6

120

up to 25

18 AWG

0-6

120

25-50

16 AWG

0-6

120

50-100

16 AWG

0-6

120

100-150

14 AWG

6-10

120

up to 25

18 AWG

6-10

120

25-50

16 AWG

6-10

120

50-100

14 AWG

6-10

120

100-150

12 AWG

10-12

120

up to 25

16 AWG

10-12

120

25-50

16 AWG

10-12

120

50-100

14 AWG

10-12

120

100-150

12 AWG

12-16

120

up to 25

14 AWG

12-16

120

25-50

12 AWG

12-16

120

GREATER THAN 50 FEET NOT RECOMMENDED

 

 

 

 

Fig. DD

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC TOOLS

Ampere

Volts

Total Length of

Gauge of

Rating

 

Cord in Feet

Extension Cord

0-6

240

up to 50

18 AWG

0-6

240

50-100

16 AWG

0-6

240

100-200

16 AWG

0-6

240

200-300

14 AWG

6-10

240

up to 50

18 AWG

6-10

240

50-100

16 AWG

6-10

240

100-200

14 AWG

6-10

240

200-300

12 AWG

10-12

240

up to 50

16 AWG

10-12

240

50-100

16 AWG

10-12

240

100-200

14 AWG

10-12

240

200-300

12 AWG

12-16

240

up to 50

14 AWG

12-16

240

50-100

12 AWG

12-16

240

GREATER THAN 100 FEET NOT RECOMMENDED

 

 

 

 

Fig. DD

OPERATING INSTRUCTIONS

FOREWORD

Delta Model 36-600 is a 10" Table Saw designed to give high quality performance with maximum depth of cut capacity up to 3-1/8" (79mm) at 90° and 2-1/8" (54mm) at 45° for clean cutting of standard stock sizes. Delta Model 36-600 includes; basic machine, sturdy steel stand, integral dust chute, a T-Square fence system, T-Slot miter gage, 15 amp motor, on/off switch, cast iron table, 22-1/4" x 38-3/8" extension wings, see-thru blade guard with anti-kickback fingers, convenient up-front blade raising and tilting controls and 10" carbide blade.

NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT

PRODUCTION MODEL. ALL OTHER ILLUSTRATIONS ARE REPRESENTATIVE

ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR

ACCESSORIES.

5

Image 5
Contents Table Saw Always Wear EYE Protection Safety RulesAdditional Safety Rules For Table Saws Power Connections Connecting Tool to Power SourceMotor Specifications Grounding InstructionsMinimum Gauge Extension Cord Extension CordsUnpacking and Cleaning For Rear Guide Rail For Saw Stand Assembling SAW To Stand Assembly InstructionsAssembling Stand Assembling Extension Wings Assembling Blade Raising and Tilting HandwheelsAssembling SAW Blade E D Assembling Guide RailsAssembling RIP Fence Leveling and Adjusting Front Guide Rail Assembling Blade Guard and Splitter Assembly Operating Controls and Adjustments Assembling RIP Fence to Guide Rails Adjusting 90 and 45 Degree Positive StopsRIP Fence Operation and Adjustments Adjusting Table Insert Miter Gage Operation and AdjustmentsRipping CROSS-CUTTINGCutterhead in a Bevel Position Using Accessory Moulding CutterheadUsing Accessory Dado Head Constructing a Featherboard Using Auxiliary Wood Facing on RIP FenceConstructing a Push Stick Push StickChanging the Blade Brush Inspection ReplacementDisconnect the Tool from the Power Source Belt ReplacementAccessories Page Canadian PORTER-CABLE Delta Service Centers