Black & Decker CS1030L instruction manual Operation

Page 10

642743-00 CS1030 CS1040L 4/13/06 10:06 AM Page 10

OPERATION

LASER LINE

SWITCH

•To operate the tool, depress the trigger switch (1). The tool will continue to run as long as the trigger is depressed.

•To turn the tool off, release the trigger switch (1). There is no provision for locking the tool on, and the switch should never be locked on by any other means.

KERF PLATE ADJUSTMENT (FIG. 15)

The tool is equipped with a sight guide for straight cutting (22) and for 45° miter cutting (23).

•Be sure the saw is unplugged.

•Adjust the kerf plate as described below.

•Align the left edge of the guides (22) or (23) with the cutting line.

•Keep the kerf plate aligned with the cutting line while sawing.

•Work with the shoe pressed against the workpiece.

ADJUSTING THE KERF PLATE

•Plug in the saw.

•Make a test cut halfway through a piece of scrap wood.

•Withdraw the saw so the cutting line becomes visible.

•While keeping the saw in this position, unplug the saw and loosen the kerf plate on the saw shoe.

15

24

2223

•Align the 0° mark (22) on the kerf plate with the cutting line. When adjusting for 45° miter cuts, align the 45° mark

(23)on the kerf plate with the cutting

line.

•Secure the kerf plate using the screw

WARNING: LASER RADIATION. Never aim the beam at a workpiece with a reflective surface. Bright shiny reflective sheet steel or similar reflective surfaces are not recommended for laser use. Reflective surfaces could direct the beam back toward the operator.

DANGER: LASER RADIATION. AVOID DIRECT EYE EXPOSURE. Do not stare into the laser light source. Never aim light at another person or object other than the workpiece. Laser light can damage your eyes.

WARNING: DO NOT use tinted glasses to enhance the laser light. Tinted glasses will reduce overall vision for the application and interfere with the normal operation of the tool.

LASER SWITCH (FIG. 16)

To turn the laser on, push forward on the laser on/off switch (2) to activate the laser line (25) as shown in figure 16.

162

25

TO USE THE LASER LINE

•Mark the line that you intend to cut on the workpiece.

•Adjust the depth and angle of cut as required.

•Push the laser on/off switch (2) to the forward “ON” position and project the laser beam.

•Depress the saw trigger switch (1) and allow the blade to reach maximum speed.

•Place the saw shoe on the workpiece. Align the laser line with the mark on the workpiece and slowly push the saw forward keeping the laser line on the mark.

•Upon completion of the cut, release the trigger and allow the saw blade to come to a complete stop before switching off the laser.

SAWING

WARNING: To reduce the risk of serious personal injury,always hold the tool with both hands.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 4 185mm Circular Saws VEA EL Español EN LA ContraportadaGeneral Safety Rules Specific Safety Rules Causes and Operator Prevention of Kickback SE These Instructions Additional Safety Rules Circular SawsLead from lead-based paints 642743-00 CS1030 CS1040L 4/13/06 1006 AM Guard Against Kickback Safety Instructions LasersTo Reduce the Risk of Kickback Overview Assembly / Adjustment SET-UPMotor Tighten the locking knob to lock the saw shoe in place Adjusting the Bevel Angle FIGTighten the lever to lock the saw shoe in place Attaching and Removing the Blade Removing the Blade CS1040LAttaching the Blade CS1030L Secure and maintain work area See Safety RulesRemoving the Blade CS1030L AttachingOperation Service Information MaintenanceAccessories Full TWO-YEAR Home USE WarrantyTechnical Specifications of Laser Center. This product is not intended for commercial useGuide D’UTILISATION Règles Générales DE Sécurité Lorsque votre corps est mis à la terreRègles DE Sécurité Spécifiques Utilisation ET Entretien DE L’OUTIL’OPÉRATEUR Performances et la sécurité de fonctionnement.VEffets DE Rebond Le plomb contenu dans les peintures à base de plombPROTÉGEZ-VOUS DES Effets DE Rebond Directives DE Sécurité Lasers Pour Réduire LE Risque D’EFFET DE RebondAperçu FIG MoteurRéglage DE LA Profondeur DE Coupe ET Configuration DE ’ASSEMBLAGE ET DES RéglagesRéglage DE L’ANGLE DE Biseau Fixation ET Dépose DE LA Lame Dépose DE LA Lame CS1040L ETDépose DE LA Lame CS1030L ET Assemblage DE LA Lame CS1040L Assemblage DE LA Lame CS1030LFournie Mesurer et marquer le bois à découperInterrupteur FonctionnementTrait Laser Réglage DE LA Plaque DE Trait DE Scie FIGSciage Interrupteur DU Laser FIGPour Utiliser LE Trait Laser Conseils Pour UNE Utilisation OptimaleEntretien AccessoiresLubrification Caractéristiques Techniques DU Laser 555326-7100 Incendio o lesiones personales graves.save Normas Generales DE SeguridadInstrucciones Seguridad PersonalUSO Y Cuidado DE LA Herramienta Normas DE Seguridad EspecíficasMantenimiento Causas DEL Retroceso Y SU Prevención POR Parte DEL Operador Retroceso Conserve Estas InstruccionesEl plomo de las pinturas de base plomo Manténgase Alerta Y EN Para Reducir EL Riesgo DE RetrocesoInstruccciones DE Seresseguridad Láseres Descripción General FIG Ajuste DEL Ángulo DE Biselado FIG ENSAMBLADO/AJUSTEAjuste DE LA Profundidad DE Corte Y Colocación DE LA Hoja CS1040LColocación Extracción DE LA Hoja CS1030L YColocación DE LA Hoja CS1030L ExtracciónFuncionamiento Línea LáserCorte Interno AserradoConsejos Para UN USO Óptimo Almacenamiento DE LA LlaveDisponibles en su comercio minorista local Garantía Completa DE DOS Años Para USO EN EL HogarEspecificaciones Técnicas DEL Láser PUEBLA, PUE CULIACAN, SIN MONTERREY, N.LGUADALAJARA, JAL MEXICO, D.F642743-00 CS1030 CS1040L 4/13/06 1006 AM 642743-00 CS1030 CS1040L 4/13/06 1006 AM 642743-00 CS1030 CS1040L 4/13/06 1006 AM

CS1030L specifications

The Black & Decker CS1030L is a powerful and efficient chainsaw designed to meet the needs of both novice users and seasoned professionals. It combines cutting-edge technology with user-friendly features, making it an excellent tool for various yard work tasks, including pruning, trimming, and cutting down small to medium-sized trees.

One of the key features of the CS1030L is its 10-inch cutting bar, which allows users to tackle a wide range of cutting jobs with ease. The chainsaw is powered by a robust 20V max lithium-ion battery, providing cordless convenience without compromising on power. The battery technology ensures extended runtime and faster charging, enabling users to complete their tasks without frequent interruptions.

Another notable aspect of the CS1030L is its lightweight design, weighing significantly less than many traditional gas-powered chainsaws. This makes it easy to maneuver, reducing user fatigue during extended use. The tool's ergonomic handle is designed for comfort and stability, providing a secure grip that enhances user control and precision while cutting.

Black & Decker has integrated several safety features into the CS1030L to ensure a secure experience. The chainsaw is equipped with a safety switch that prevents accidental start-ups, and a hand guard to protect users from debris. The automatic oiling system also ensures that the chain remains properly lubricated, which enhances cutting performance and extends the life of the chain and bar.

In terms of maintenance, the CS1030L is user-friendly, featuring a tool-free chain tensioning system that allows for quick adjustments and replacements. This efficient feature makes it easy to keep the chainsaw in optimal working condition without needing additional tools.

Additionally, the chainsaw is designed for low noise operation, making it an excellent choice for residential areas where sound reduction is a priority. The combination of its eco-friendly electric power and minimal emissions makes the CS1030L an attractive option for environmentally conscious users.

Overall, the Black & Decker CS1030L is a practical and versatile chainsaw that delivers performance and reliability. With its advanced technologies, user-friendly features, and safety enhancements, it stands out as a top choice for homeowners and DIY enthusiasts looking to efficiently maintain their outdoor spaces.
Top Page Image Contents