Black & Decker CS1030L instruction manual Safety Instructions Lasers, Guard Against Kickback

Page 6

642743-00 CS1030 CS1040L 4/13/06 10:06 AM Page 6

•STAY ALERT AND EXERCISE CONTROL. Keep body positioned to one side of blade. Always maintain a firm grip and control of saw with both hands. Do not change hand grip or body position while saw is running. Take precaution to avoid injury from cut off pieces and other falling material during operation.

DANGER: RELEASE SWITCH IMMEDIATELY IF BLADE BINDS OR SAW STALLS

GUARD AGAINST KICKBACK

•KICKBACK CAN BE CAUSED BY the saw blade becoming pinched, twisted or bound while cutting, or when the saw stalls. When the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade to climb out of the cut and move suddenly back toward the operator.

TO REDUCE THE RISK OF KICKBACK

•Keep a firm grip on saw with both hands at all times.

•Stay alert – exercise control.

•Support long overhanging materials. As the material is cut and weakens, it will sag, causing a pinched blade.

•Support large panels as shown (Fig. 1). Material supported only at the ends (Fig. 2) will lead to blade pinching.

•Avoid sawing overhead. Material can sag and will pinch blade.

•Keep blades sharp and clean.

•Use fence or straight edge guide when ripping. Be careful as the cut off strip can sag or twist, closing the cut and pinching the blade, leading to KICKBACK.

•Don’t force tool. Wood variables such as knots, hardness, toughness, wetness, pressure treated and freshly cut green lumber can heavily load the saw which can lead to stalling. Push the saw slower when this occurs.

•Don’t remove saw from work during a cut while the blade is moving.

•Allow saw to reach full speed before blade contacts material to be cut. Starting the saw with the blade against the work or pushed forward into cut can lead to stalling or sudden backward movement of saw.

•Never attempt to lift saw when making a bevel cut. This leads to blade binding and stalling.

•Always secure work to prevent workpiece movement during cut.

•Do not try to force saw back on line if your cut begins to go off line. This can cause KICKBACK. Stop saw and allow blade to coast down to a stop. Withdraw from cut and start a new cut on the line.

•Set depth adjustment of saw such that

one tooth of the blade projects below the workpiece as shown in (figure 8).

•Do not back up a rotating blade in the cut. Twisting the saw can cause the back edge of the blade to dig into the material, climb out of the work and run back toward the operator.

•Avoid cutting nails. Inspect for and remove all nails from lumber before cutting.

SAFETY INSTRUCTIONS -

LASERS

DANGER: Laser radiation, avoid direct eye exposure, serious eye injury can result.

•Do not use optical tools such as a telescope or transit to view the laser beam.

•Position the laser so unintentional eye contact will be avoided.

•Do not operate the laser around children or allow children to operate the laser.

•Do not disassemble. Modifying the product in any way can increase the risk of laser radiation.

WARNING: Use of controls or adjustments or performance of procedures other than those specified in this manual may result in hazardous laser radiation exposure.

•Do not operate in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.

•Store idle product out of reach of children and other untrained persons. Lasers / power tools are dangerous in the hands of untrained users.

•Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one laser / power tool, may create a risk of injury when used on another laser / power tool.

•Repairs and servicing MUST be performed by a qualified repair facility. Repairs performed by unqualified personnel could result in serious injury.

•Do not remove or deface warning labels. Removing labels increases the risk of exposure to radiation.

•For indoor use only.

•This product is intended for use in a temperature range of 41°F(5°C) - 104°F(40°C).

NOTE: Laser is set at the factory and is not adjustable.

CAUTION: Use of controls or adjustments or performance of

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents 4 185mm Circular Saws VEA EL Español EN LA ContraportadaGeneral Safety Rules Specific Safety Rules SE These Instructions Additional Safety Rules Circular Saws Causes and Operator Prevention of KickbackLead from lead-based paints 642743-00 CS1030 CS1040L 4/13/06 1006 AM Safety Instructions Lasers Guard Against KickbackTo Reduce the Risk of Kickback Assembly / Adjustment SET-UP OverviewMotor Tighten the locking knob to lock the saw shoe in place Adjusting the Bevel Angle FIGTighten the lever to lock the saw shoe in place Attaching and Removing the Blade Removing the Blade CS1040LAttaching the Blade CS1030L Secure and maintain work area See Safety RulesRemoving the Blade CS1030L AttachingOperation Service Information MaintenanceAccessories Full TWO-YEAR Home USE WarrantyTechnical Specifications of Laser Center. This product is not intended for commercial useGuide D’UTILISATION Règles Générales DE Sécurité Lorsque votre corps est mis à la terreRègles DE Sécurité Spécifiques Utilisation ET Entretien DE L’OUTIL’OPÉRATEUR Performances et la sécurité de fonctionnement.VEffets DE Rebond Le plomb contenu dans les peintures à base de plombPROTÉGEZ-VOUS DES Effets DE Rebond Directives DE Sécurité Lasers Pour Réduire LE Risque D’EFFET DE RebondAperçu FIG MoteurRéglage DE LA Profondeur DE Coupe ET Configuration DE ’ASSEMBLAGE ET DES RéglagesRéglage DE L’ANGLE DE Biseau Fixation ET Dépose DE LA Lame Dépose DE LA Lame CS1040L ETDépose DE LA Lame CS1030L ET Assemblage DE LA Lame CS1040L Assemblage DE LA Lame CS1030LFournie Mesurer et marquer le bois à découperInterrupteur FonctionnementTrait Laser Réglage DE LA Plaque DE Trait DE Scie FIGSciage Interrupteur DU Laser FIGPour Utiliser LE Trait Laser Conseils Pour UNE Utilisation OptimaleAccessoires EntretienLubrification Caractéristiques Techniques DU Laser 555326-7100 Incendio o lesiones personales graves.save Normas Generales DE SeguridadInstrucciones Seguridad PersonalNormas DE Seguridad Específicas USO Y Cuidado DE LA HerramientaMantenimiento Causas DEL Retroceso Y SU Prevención POR Parte DEL Operador Conserve Estas Instrucciones RetrocesoEl plomo de las pinturas de base plomo Manténgase Alerta Y EN Para Reducir EL Riesgo DE RetrocesoInstruccciones DE Seresseguridad Láseres Descripción General FIG Ajuste DEL Ángulo DE Biselado FIG ENSAMBLADO/AJUSTEAjuste DE LA Profundidad DE Corte Y Colocación DE LA Hoja CS1040LColocación Extracción DE LA Hoja CS1030L YColocación DE LA Hoja CS1030L ExtracciónFuncionamiento Línea LáserCorte Interno AserradoConsejos Para UN USO Óptimo Almacenamiento DE LA LlaveDisponibles en su comercio minorista local Garantía Completa DE DOS Años Para USO EN EL HogarEspecificaciones Técnicas DEL Láser PUEBLA, PUE CULIACAN, SIN MONTERREY, N.LGUADALAJARA, JAL MEXICO, D.F642743-00 CS1030 CS1040L 4/13/06 1006 AM 642743-00 CS1030 CS1040L 4/13/06 1006 AM 642743-00 CS1030 CS1040L 4/13/06 1006 AM

CS1030L specifications

The Black & Decker CS1030L is a powerful and efficient chainsaw designed to meet the needs of both novice users and seasoned professionals. It combines cutting-edge technology with user-friendly features, making it an excellent tool for various yard work tasks, including pruning, trimming, and cutting down small to medium-sized trees.

One of the key features of the CS1030L is its 10-inch cutting bar, which allows users to tackle a wide range of cutting jobs with ease. The chainsaw is powered by a robust 20V max lithium-ion battery, providing cordless convenience without compromising on power. The battery technology ensures extended runtime and faster charging, enabling users to complete their tasks without frequent interruptions.

Another notable aspect of the CS1030L is its lightweight design, weighing significantly less than many traditional gas-powered chainsaws. This makes it easy to maneuver, reducing user fatigue during extended use. The tool's ergonomic handle is designed for comfort and stability, providing a secure grip that enhances user control and precision while cutting.

Black & Decker has integrated several safety features into the CS1030L to ensure a secure experience. The chainsaw is equipped with a safety switch that prevents accidental start-ups, and a hand guard to protect users from debris. The automatic oiling system also ensures that the chain remains properly lubricated, which enhances cutting performance and extends the life of the chain and bar.

In terms of maintenance, the CS1030L is user-friendly, featuring a tool-free chain tensioning system that allows for quick adjustments and replacements. This efficient feature makes it easy to keep the chainsaw in optimal working condition without needing additional tools.

Additionally, the chainsaw is designed for low noise operation, making it an excellent choice for residential areas where sound reduction is a priority. The combination of its eco-friendly electric power and minimal emissions makes the CS1030L an attractive option for environmentally conscious users.

Overall, the Black & Decker CS1030L is a practical and versatile chainsaw that delivers performance and reliability. With its advanced technologies, user-friendly features, and safety enhancements, it stands out as a top choice for homeowners and DIY enthusiasts looking to efficiently maintain their outdoor spaces.
Top Page Image Contents