Black & Decker CS1030L Hints for Optimum USE, Pocket Cutting, Wrench Storage, Maintenance

Page 11

642743-00 CS1030 CS1040L 4/13/06 10:06 AM Page 11

•Let the blade run freely for a few seconds before starting the cut.

•Apply only a gentle pressure to the tool while performing the cut.

•Work with the shoe pressed against the workpiece.

HINTS FOR OPTIMUM USE

•As some splintering along the line of cut on the top side of the workpiece cannot be avoided, cut on the side where splintering is acceptable.

•Where splintering is to be minimized, e.g. when cutting laminates, clamp a piece of plywood onto the top of the workpiece.

POCKET CUTTING (FIG.17)

POCKET CUTTING IS USED TO CUTA HOLE IN APIECE OF MATERIAL WITHOUT CUTTING FROM THE SIDE.

•Measure and mark work.

•Tilt saw forward and rest front of the shoe on material to be cut. Align so that cut will begin at the back of the drawn rectangle shown in figure 17.

17

•Using the retracting lever, retract blade guard to an upward position, with the blade just clearing the material, start motor and gradually lower the saw into the material.

WARNING: As blade starts cutting the material, release the retracting lever immediately.

•Never tie the blade guard in a raised position.

•When the shoe rests flat on the material being cut, complete the cut in forward direction.

•Allow the blade to come to a complete stop before lifting saw from material.

•When starting each new cut, repeat the above steps.

WRENCH STORAGE (FIG.18)

The blade wrench (10) can be stored on the saw shoe as shown in figure 18.

18

10

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.

LUBRICATION

Black & Decker tools are properly lubricated at the factory and are ready for use.

ACCESSORIES

Recommended accessories for use with your tool are available from your local retailer.

WARNING:The use of any accessory not recommended for use with this tool could be hazardous. Use only 7-1/4 “ (185mm) blades with 5/8” diameter arbor. Exception: 7" (175 mm) abrasive blades can be used.

When cutting metal, be careful of hot sparks which are thrown by the blade.

SERVICE INFORMATION

All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools— Electric" or call: 1-800-544-6986 or visit

www.blackanddecker.com

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents VEA EL Español EN LA Contraportada 4 185mm Circular SawsGeneral Safety Rules Specific Safety Rules Lead from lead-based paints SE These Instructions Additional Safety Rules Circular SawsCauses and Operator Prevention of Kickback 642743-00 CS1030 CS1040L 4/13/06 1006 AM To Reduce the Risk of Kickback Safety Instructions LasersGuard Against Kickback Motor Assembly / Adjustment SET-UPOverview Attaching and Removing the Blade Removing the Blade CS1040L Adjusting the Bevel Angle FIGTighten the lever to lock the saw shoe in place Tighten the locking knob to lock the saw shoe in placeAttaching Secure and maintain work area See Safety RulesRemoving the Blade CS1030L Attaching the Blade CS1030LOperation Full TWO-YEAR Home USE Warranty MaintenanceAccessories Service InformationCenter. This product is not intended for commercial use Technical Specifications of LaserGuide D’UTILISATION Lorsque votre corps est mis à la terre Règles Générales DE SécuritéUtilisation ET Entretien DE L’OUTIL Règles DE Sécurité SpécifiquesPerformances et la sécurité de fonctionnement.V ’OPÉRATEURLe plomb contenu dans les peintures à base de plomb Effets DE RebondPROTÉGEZ-VOUS DES Effets DE Rebond Pour Réduire LE Risque D’EFFET DE Rebond Directives DE Sécurité LasersMoteur Aperçu FIGFixation ET Dépose DE LA Lame Dépose DE LA Lame CS1040L ET Configuration DE ’ASSEMBLAGE ET DES RéglagesRéglage DE L’ANGLE DE Biseau Réglage DE LA Profondeur DE Coupe ETMesurer et marquer le bois à découper Assemblage DE LA Lame CS1040L Assemblage DE LA Lame CS1030LFournie Dépose DE LA Lame CS1030L ETRéglage DE LA Plaque DE Trait DE Scie FIG FonctionnementTrait Laser InterrupteurConseils Pour UNE Utilisation Optimale Interrupteur DU Laser FIGPour Utiliser LE Trait Laser SciageLubrification AccessoiresEntretien Caractéristiques Techniques DU Laser 555326-7100 Seguridad Personal Normas Generales DE SeguridadInstrucciones Incendio o lesiones personales graves.saveMantenimiento Normas DE Seguridad EspecíficasUSO Y Cuidado DE LA Herramienta Causas DEL Retroceso Y SU Prevención POR Parte DEL Operador El plomo de las pinturas de base plomo Conserve Estas InstruccionesRetroceso Para Reducir EL Riesgo DE Retroceso Manténgase Alerta Y ENInstruccciones DE Seresseguridad Láseres Descripción General FIG Colocación DE LA Hoja CS1040L ENSAMBLADO/AJUSTEAjuste DE LA Profundidad DE Corte Y Ajuste DEL Ángulo DE Biselado FIGExtracción Extracción DE LA Hoja CS1030L YColocación DE LA Hoja CS1030L ColocaciónLínea Láser FuncionamientoAlmacenamiento DE LA Llave AserradoConsejos Para UN USO Óptimo Corte InternoGarantía Completa DE DOS Años Para USO EN EL Hogar Disponibles en su comercio minorista localEspecificaciones Técnicas DEL Láser MEXICO, D.F CULIACAN, SIN MONTERREY, N.LGUADALAJARA, JAL PUEBLA, PUE642743-00 CS1030 CS1040L 4/13/06 1006 AM 642743-00 CS1030 CS1040L 4/13/06 1006 AM 642743-00 CS1030 CS1040L 4/13/06 1006 AM

CS1030L specifications

The Black & Decker CS1030L is a powerful and efficient chainsaw designed to meet the needs of both novice users and seasoned professionals. It combines cutting-edge technology with user-friendly features, making it an excellent tool for various yard work tasks, including pruning, trimming, and cutting down small to medium-sized trees.

One of the key features of the CS1030L is its 10-inch cutting bar, which allows users to tackle a wide range of cutting jobs with ease. The chainsaw is powered by a robust 20V max lithium-ion battery, providing cordless convenience without compromising on power. The battery technology ensures extended runtime and faster charging, enabling users to complete their tasks without frequent interruptions.

Another notable aspect of the CS1030L is its lightweight design, weighing significantly less than many traditional gas-powered chainsaws. This makes it easy to maneuver, reducing user fatigue during extended use. The tool's ergonomic handle is designed for comfort and stability, providing a secure grip that enhances user control and precision while cutting.

Black & Decker has integrated several safety features into the CS1030L to ensure a secure experience. The chainsaw is equipped with a safety switch that prevents accidental start-ups, and a hand guard to protect users from debris. The automatic oiling system also ensures that the chain remains properly lubricated, which enhances cutting performance and extends the life of the chain and bar.

In terms of maintenance, the CS1030L is user-friendly, featuring a tool-free chain tensioning system that allows for quick adjustments and replacements. This efficient feature makes it easy to keep the chainsaw in optimal working condition without needing additional tools.

Additionally, the chainsaw is designed for low noise operation, making it an excellent choice for residential areas where sound reduction is a priority. The combination of its eco-friendly electric power and minimal emissions makes the CS1030L an attractive option for environmentally conscious users.

Overall, the Black & Decker CS1030L is a practical and versatile chainsaw that delivers performance and reliability. With its advanced technologies, user-friendly features, and safety enhancements, it stands out as a top choice for homeowners and DIY enthusiasts looking to efficiently maintain their outdoor spaces.
Top Page Image Contents