Black & Decker CS1030L Causes and Operator Prevention of Kickback, Lead from lead-based paints

Page 4

642743-00 CS1030 CS1040L 4/13/06 10:06 AM Page 4

contact hidden wiring or its own cord. Contact with a “live” wire will also make exposed metal parts of the tool “live” and shock the operator.

When ripping, always use a rip fence or straight edge guide. This improves the accuracy of cut and reduces the chance for blade binding.

Always use blades with correct size and shape (diamond vs. round) arbor holes. Blades that do not match the mounting hardware of the saw will run eccentrically, causing loss of control.

Never use damaged or incorrect blade washers or bolts. The blade washers and bolt were specially designed for your saw, for optimum performance and safety of operation.

CAUSES AND OPERATOR

PREVENTION OF KICKBACK:

Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator.

When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator.

If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade to climb out of the kerf and jump back toward operator.

Kickback is the result of tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.

a.Maintain a firm grip with both hands on the saw and position your body and arm to allow you to resist KICKBACK forces. Kickback forces can be controlled by the operator, if proper precautions are taken.

b.When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a

complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or KICKBACK may occur. Investigate and take corrective actions to eliminate the cause of blade binding.

c. When restarting a saw in the workpiece, center the saw blade in the kerf and check that the saw teeth are not engaged into the material. If saw blade is binding, it may walk up or KICKBACK from the workpiece as the saw is restarted.

d. Support large panels to minimize the risk of blade pinching and KICKBACK. Large panels tend to sag under their own weight. Support must be placed under the panel on both sides, near the line of cut and near the edge of the panel.

e. Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding, and KICKBACK.

f.Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and KICKBACK.

g.Use extra caution when making a “Pocket Cut” into existing walls or other blind areas. The protruding blade may cut objects that can cause KICKBACK.

SAVE THESE INSTRUCTIONS

SE THESE INSTRUCTIONS ADDITIONAL SAFETY RULES:

CIRCULAR SAWS

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products,

arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type

4

Image 4
Contents 4 185mm Circular Saws VEA EL Español EN LA ContraportadaGeneral Safety Rules Specific Safety Rules Causes and Operator Prevention of Kickback SE These Instructions Additional Safety Rules Circular SawsLead from lead-based paints 642743-00 CS1030 CS1040L 4/13/06 1006 AM Guard Against Kickback Safety Instructions LasersTo Reduce the Risk of Kickback Overview Assembly / Adjustment SET-UPMotor Adjusting the Bevel Angle FIG Tighten the lever to lock the saw shoe in placeTighten the locking knob to lock the saw shoe in place Attaching and Removing the Blade Removing the Blade CS1040LSecure and maintain work area See Safety Rules Removing the Blade CS1030LAttaching the Blade CS1030L AttachingOperation Maintenance AccessoriesService Information Full TWO-YEAR Home USE WarrantyTechnical Specifications of Laser Center. This product is not intended for commercial useGuide D’UTILISATION Règles Générales DE Sécurité Lorsque votre corps est mis à la terreRègles DE Sécurité Spécifiques Utilisation ET Entretien DE L’OUTIL’OPÉRATEUR Performances et la sécurité de fonctionnement.VEffets DE Rebond Le plomb contenu dans les peintures à base de plombPROTÉGEZ-VOUS DES Effets DE Rebond Directives DE Sécurité Lasers Pour Réduire LE Risque D’EFFET DE RebondAperçu FIG MoteurConfiguration DE ’ASSEMBLAGE ET DES Réglages Réglage DE L’ANGLE DE BiseauRéglage DE LA Profondeur DE Coupe ET Fixation ET Dépose DE LA Lame Dépose DE LA Lame CS1040L ETAssemblage DE LA Lame CS1040L Assemblage DE LA Lame CS1030L FournieDépose DE LA Lame CS1030L ET Mesurer et marquer le bois à découperFonctionnement Trait LaserInterrupteur Réglage DE LA Plaque DE Trait DE Scie FIGInterrupteur DU Laser FIG Pour Utiliser LE Trait LaserSciage Conseils Pour UNE Utilisation OptimaleEntretien AccessoiresLubrification Caractéristiques Techniques DU Laser 555326-7100 Normas Generales DE Seguridad InstruccionesIncendio o lesiones personales graves.save Seguridad PersonalUSO Y Cuidado DE LA Herramienta Normas DE Seguridad EspecíficasMantenimiento Causas DEL Retroceso Y SU Prevención POR Parte DEL Operador Retroceso Conserve Estas InstruccionesEl plomo de las pinturas de base plomo Manténgase Alerta Y EN Para Reducir EL Riesgo DE RetrocesoInstruccciones DE Seresseguridad Láseres Descripción General FIG ENSAMBLADO/AJUSTE Ajuste DE LA Profundidad DE Corte YAjuste DEL Ángulo DE Biselado FIG Colocación DE LA Hoja CS1040LExtracción DE LA Hoja CS1030L Y Colocación DE LA Hoja CS1030LColocación ExtracciónFuncionamiento Línea LáserAserrado Consejos Para UN USO ÓptimoCorte Interno Almacenamiento DE LA LlaveDisponibles en su comercio minorista local Garantía Completa DE DOS Años Para USO EN EL HogarEspecificaciones Técnicas DEL Láser CULIACAN, SIN MONTERREY, N.L GUADALAJARA, JALPUEBLA, PUE MEXICO, D.F642743-00 CS1030 CS1040L 4/13/06 1006 AM 642743-00 CS1030 CS1040L 4/13/06 1006 AM 642743-00 CS1030 CS1040L 4/13/06 1006 AM

CS1030L specifications

The Black & Decker CS1030L is a powerful and efficient chainsaw designed to meet the needs of both novice users and seasoned professionals. It combines cutting-edge technology with user-friendly features, making it an excellent tool for various yard work tasks, including pruning, trimming, and cutting down small to medium-sized trees.

One of the key features of the CS1030L is its 10-inch cutting bar, which allows users to tackle a wide range of cutting jobs with ease. The chainsaw is powered by a robust 20V max lithium-ion battery, providing cordless convenience without compromising on power. The battery technology ensures extended runtime and faster charging, enabling users to complete their tasks without frequent interruptions.

Another notable aspect of the CS1030L is its lightweight design, weighing significantly less than many traditional gas-powered chainsaws. This makes it easy to maneuver, reducing user fatigue during extended use. The tool's ergonomic handle is designed for comfort and stability, providing a secure grip that enhances user control and precision while cutting.

Black & Decker has integrated several safety features into the CS1030L to ensure a secure experience. The chainsaw is equipped with a safety switch that prevents accidental start-ups, and a hand guard to protect users from debris. The automatic oiling system also ensures that the chain remains properly lubricated, which enhances cutting performance and extends the life of the chain and bar.

In terms of maintenance, the CS1030L is user-friendly, featuring a tool-free chain tensioning system that allows for quick adjustments and replacements. This efficient feature makes it easy to keep the chainsaw in optimal working condition without needing additional tools.

Additionally, the chainsaw is designed for low noise operation, making it an excellent choice for residential areas where sound reduction is a priority. The combination of its eco-friendly electric power and minimal emissions makes the CS1030L an attractive option for environmentally conscious users.

Overall, the Black & Decker CS1030L is a practical and versatile chainsaw that delivers performance and reliability. With its advanced technologies, user-friendly features, and safety enhancements, it stands out as a top choice for homeowners and DIY enthusiasts looking to efficiently maintain their outdoor spaces.