Black & Decker 90521029 instruction manual Assembling Stand, Attaching the BAG, SAW to Stand

Page 11

ASSEMBLING STAND

1.Attach the rubber feet (H) Fig. 11 to the bottom of each leg (F).

Locate the two legs (F) which have holes at the bottom for attaching the wheel brackets (G) and brace (E). (Make sure wheels and brackets are properly oriented. See inset Figure 11.) To attach the brackets, remove the nuts from the bolts and insert the bolts through the holes in the bottom of the two legs and into the holes in brace (E). Thread the nuts back on the bolts and tighten. Assemble the stand as shown in Fig. 11, using 16 M8x1.25x20mm carriage head bolts, 3/8" flat washers and M8x1.25 hex nuts. Align the holes in the stand legs (F) with the holes in the brackets. Insert the carriage head bolt through the hole in the leg and the hole in the bracket, place a flat washer on the carriage head bolt and thread a hex nut onto the carriage head bolt. Repeat this process for the 15 remaining holes in the legs and brackets.

NOTE: Loosely tighten the hardware for further adjustment.

Letters are on the stand brackets to ease assembly: A - Top front and rear brackets

B - Top side brackets C - Bottom side brackets

D - Bottom front and rear brackets E - Bottom brace

NOTE: Each rubber foot is provided with holes for mounting the stand to the floor surface if required.

ATTACHING THE BAG

1.Attach the dust bag to the bag frame and place the frame of the dust bag inside the saw stand as shown in Fig. 12. Refer to the section below to attach this assembly to the saw.

SAW TO STAND

1.Turn saw table face down on a piece of cardboard to protect the table surface. Place stand upside down onto saw and align the four holes in the stand with the mounting holes in the saw.

2.Place a 3/8" flat washer on a M8x1.25x45mm hex head screw. Insert the hex head screw through the mounting hole in the saw and the mounting hole in the stand. Place another 3/8" flat washer on the hex head screw and thread a M8x1.25 hex nut on the screw and loosely tighten. Complete this process for the other three holes.

3.Stand the saw upright, as shown in Fig. 13 (Saw is shown fully assembled here).

4.Push down on top of the saw so that the legs of the stand adjust to the surface of the floor. Tighten all hardware securely.

B

A

F

C

H

D

G

E

Wheel

Fig. 11

Fig. 12

Fig. 13

11

Image 11

Contents Before Returning this Product for ANY FS200SD 10 Table SAWTable of Contents California Proposition Safety Guidelines DefinitionsImportant Safety Instructions General Safety RulesAdditional Specific Safety Rules Grounding Instructions Power ConnectionsFunctional Description Carton ContentsParts Elevating and Supporting Surfaces for a SAW with no Stand AssemblyUnpacking and Cleaning Assembly Tools RequiredMiter Gauge Attaching Miter Gauge HolderSAW to Stand Assembling StandAttaching the BAG Attaching Blade Guard and Splitter Assembly Attaching Blade Height Adjusting HandwheelOn the screw L Fig Assembling RIP Fence Operation Operational Controls and AdjustmentsTo Adjust Positive Stop AT 45 Degrees Blade Tilt Adjustment45 Degree Positive Stop Adjustments Table Insert Adjustment RIP Fence Operation AdjustmentsAdjusting Blade Parallel to Miter Gauge Slots Miter Gauge Operation AdjustmentsCROSS-CUTTING Machine USEChanging the Blade Ripping Never USE the Fence AS a CUT-OFF Gage When CROSS-CUTTINGGuard Removed for CLARITY. Always USE the Guard Using Auxiliary Wood Facing on RIP FenceAccessory Dado Cutterhead Page Constructing a Push Stick Push StickConstructing a Featherboard WHAT’S WRONG? What to DO… TroubleshootingWarranty MaintenanceAccessories ServiceScie Circulaire À Table DE 254 MM 10 PO FS200SD Conserver CES Directives Lignes Directrices EN Matière DE Sécurité DéfinitionsProposition 65 DE LA Californie Directives DE Sécurité Importantes Règles Générales DE SécuritéPour Éviter L’EFFET DE Rebond Règles DE Sécurité Spécifiques SupplémentairesDirectives DE Mise À LA Terre Connexions ÉlectriquesIntroduction Description FonctionnelleContenu DU Carton Rallonges ÉlectriquesSurfaces DE Levage ET DE Support Pour UNE Scie Sans Socle AssemblageDésemballage ET Nettoyage Outils Nécessaires Pour L’ASSEMBLAGEFixation DU SAC Fixation DU PORTE-JAUGE À OngletJauge À Onglet Assemblage DU SocleFonctionnement Commandes ET Réglages OpérationnelsUtilisation ET Réglages DU Guide Longitudinal Réglage DE LA Hauteur DE LA LameRéglage DE L’INCLINAISON DE LA Lame Réglages DES Butées Fixes À 90 ET 45 DegrésTronçonnage Utilisation DE LA MachineUtilisation ET Réglages DE LA Jauge À Onglet Changement DE LA LameUtiliser LE Dispositif DE Protection Sciage EN Long« Fabrication DUN Poussoir » Fraise Accessoire À RainurerFabrication D’UNE Planche EN Éventail DépannageEntretien Accessoires Sierra DE Banco FS200SD Proposición DE California Pautas DE SEGURIDAD/DEFINICIONESInstrucciones Importantes Sobre Seguridad Normas Generales DE SeguridadEvite EL Retroceso Reglas DE Seguridad Adicionales Para Sierra DE MesaInstrucciones DE Conexión a Tierra Conexiones a LA Fuente DE AlimentaciónCordón DE Extensión DE Calibre Mínimo Instrucciones DE FuncionamientoContenido DE Carton Cordones DE ExtensiónEL VIO Apoyo Debe SER Fijo Y Capaz DE Sostener 300 Libras EnsamblajeDesempaquetado Y Limpieza Herramientas DE Ensamblaje RequeridasSierra QUE Ensambla Ensamblado DEL Portador DE LA Escuadra DE IngletesEscuadra DE Ingletes Montaje DE LA Base DE SoporteEnsamblado DE LA Guia DE Corte a LO Largo Ensamblado DEL Volante DE Inclinacion Y Elevado DE HojaEnsamblado DEL Ensamblaje DE Protector DE Hoya Y Hendidor Controles Y Ajustes Operacionales OperaciónFuncionamiento Y Ajustes DE LA Escuadra DE Ingletes Funcionamiento Y Ajustes DE LA Guia DE Corte a LO LargoAjuste DEL Inserto Para Mesa Realización DE Cortes AL Hilo Utilizar LA MaquinaCambio DE LA Hoja Realización DE Cortes TransversalesPalo DE Empujar Fresa DE Ranurar AccesoriaConstrucción DE UNA Tabla DE Canto Biselado Construcción DE UN Palo DE EmpujarFalla EN EL Encendido Detección DE ProblemasMantenga LA Máquina Limpia Para Otras Localidades Llame AL 55 5326 RéparationPage