Black & Decker FS5500JS, 587384-01 instruction manual OperationUSE, Hints for Optimum Use, Assembly

E	F
	Ha
	Ia

G Hb

Hc Ib

Ic J

Use of Extension Cords

Make sure the extension cord is in good condition before using. Always use the proper size extension cords with the tool – that is, proper wire size for various lengths of cord and heavy enough to carry the current the tool will draw. Use of an undersized cord will cause a drop in line voltage resulting in loss of power and overheating. For proper size cords see chart.

Volts			Minimum Gage for Cord Sets
			0-25	Total Length of Cord in Feet
120V				26-50	51-100	101-150
240V			0-50	51-100	101-200	201-300
Ampere Rating				American Wire Gage
More		Not more
Than	-	Than	18	16	16	14
0		6
6	-	10	18	16	14	12
10	-	12	16	16	14	12
12	-	16	14	12	Not Recommended

OperationUSE

WARNING: Laceration Hazard. To prevent loss of control, never use the tool when the saw shoe is loose or removed. Failure to do this could result in serious personal injury.

Adjusting the shoe plate for bevel cuts (fig. E)

The shoe plate can be set to a left or right bevel angle of up to 45°.

-Turn the locking knob (11) in direction A to release the shoe plate (10).

-Pull the shoe plate (10) backwards and set it to the required angle. You can use the scale or a protractor to check the angle.

-Turn the locking knob (11) in direction B to lock the shoe plate in place.

To reset the shoe plate for straight cuts:

-Turn the locking knob (11) in direction A to release the shoe plate (10).

-Pull the shoe plate backwards and set it to an angle of approximately 0.

-Push the shoe plate forward.

-Turn the locking knob (11) in direction B to lock the shoe plate in place. Make sure that the shoe plate is supported by the guide ribs.

Variable speed control

-Set the variable speed control knob (3) to the required speed range. Use a high speed for wood, medium speed for aluminum and PVC and low speed for metals other than aluminum.

Switching On and Off

-To switch the tool on, press the on/off switch (1).

-For continuous operation, press the lock-on button (2) and release the on/off switch.

-To switch the tool off, release the on/off switch. To switch the tool off, when in continuous operation, press the on/off switch once more and release it.

Using the mode selector

The mode selector (9) can set in 3 positions

1.Scrolling position (figs F and G) - this position allows the scroller knob (8) to be rotated for intricate and accurate sawing. (In this position there is no orbital action.) It is recommended to use scroller blades when in this mode.

2.Straight cutting position (figs Ha, Hb and Hc ) this position turns off orbital action and locks the scroller knob to prevent its rotation. The scroller knob can be locked in any of 4 positions for straight cutting.

Method of engagement:

a.Turn the Mode Selector to the scrolling position.

b.Rotate the scroller knob to the desired position (this can be any of 4 positions - the blade can point forwards, reverse, left or right).

c.Turn the Mode Selector to the neutral position. (In this position the Scroller Knob cannot be turned).

3.Orbital Action Position (figs Ia, Ib and Ic) - this position switches on the orbital action for fast and efficient straight cuts. This mode can only be selected with the blade pointing forwards.

Method of engagement:

a. Turn the mode selector to the scrolling position.

b. Rotate the scroller knob to point the blade forwards.

c. Turn the Mode Selector to the orbital position. (In this position the Scroller Knob cannot be turned).

How to Use the Sightline® Feature (fig. J)

-Use a pencil to mark the cutting line.

-Position the jigsaw over the line (19).

Viewing from directly above the jigsaw the line of cut can be easily followed. Should this view be restricted for any reason, the indent (20) can be used as an alternate cutting guide.

Hints for Optimum Use

General

-Use a high speed for wood, a medium speed for aluminum and PVC and a low speed for metals other than aluminum.

Sawing laminates

As the saw blade cuts on the upward stroke, splintering may occur on the surface closest to the shoe plate.

-Use a fine-tooth saw blade.

-Saw from the back surface of the workpiece.

-To minimize splintering, clamp a piece of scrap wood or hardboard to both sides of the workpiece and saw through this sandwich.

Sawing metal

-Be aware that sawing metal takes much more time than sawing wood.

-Use a saw blade suitable for sawing metal.

-When cutting thin metal, clamp a piece of scrap wood to the back surface of the workpiece and cut through this sandwich.

-Spread a film of oil along the intended line of cut.

WARNING: Fire Hazard. Do not use vacuum adapter when cutting metal. Metal

filings will be hot and could cause a fire in the vacuum container.

Maintenance

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts.

Motor

Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. A rating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC or DC power. This information is printed on the nameplate. Lower voltage will cause loss of power and can result in over-heating. All Black & Decker tools are factory-tested; if this tool does not operate, check the power supply.

SAVE THESE INSTRUCTIONS

Assembly

WARNING: Sharp blade. To prevent accidental operation, turn off and unplug saw before performing the following operations. Failure to do this could result in serious personal injury.

Fitting the saw blade (fig. A)

-Hold the saw blade (7) as shown, with teeth facing forward.

-Push the lever (4) downwards.

-Insert the shank of the saw blade into the blade holder (15) as far as it will go.

-Release the lever.

-Adjust the blade support roller as described below.

AccuCutTM blade support roller (fig. B)

After fitting the blade, you need to adjust the blade support roller (5).

Screwdriver Method

-Turn the slotted blade support adjustment screw (6) in direction A.

-Slide the blade support roller against the rear of the blade. The blade must locate in the central recess of the roller.

-Turn the blade support adjustment screw in direction B to lock the blade support in place.

Tool Free Method

-The blade support roller can be adjusted in a “tool free” manner, by turning the scroll

ing knob (8) so that the adjustment screw is rotated around to the front of the unit where it can be turned by hand.

Accessories

Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:

1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this tool could be hazardous.

Service Information

Black & Decker offers a full network of company-owned and authorized service locations throughout North America. All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the

Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call: 1-800-544-6986.

Full Two-Year Home Use Warranty

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways. The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed under "Tools–Electric" in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state. Should you have any questions, contact the manager of your nearest Black & Decker Service Center.

This product is not intended for commercial use.

Free Warning Label Replacement: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free replacement.

Connecting a vacuum cleaner to the tool (fig. C & D)

-Align the dust extraction adaptor (14) with the saw shoe as shown.

-Insert the ribs (16) into the slots (17).

-Pull the adaptor towards the rear of the jigsaw to secure.

-Connect the vacuum cleaner hose (18) (not supplied) to the adaptor.

-Dust extraction is not possible when making bevel cuts.

WARNING: Fire Hazard. Do not use vacuum adapter when cutting metal. Metal filings will be hot and could cause a fire in the vacuum container.

Imported by	See ‘Tools-Electric’
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.	– Yellow Pages –
Towson, MD 21286 U.S.A.	for Service & Sales