Configuring
The CMAC_LOG_POWER_LEVEL_IS field is the power level that the CMTS told the Cisco uBR900 series
to adjust to. The CMAC_LOG_RANGING_SUCCESS | field indicates that the ranging adjustment was | ||
successful. |
|
|
|
508148.062 | CMAC_LOG_STATE_CHANGE | ranging_1_state | |
508148.064 | CMAC_LOG_RANGING_OFFSET_SET_TO | 9610 |
|
508148.066 | CMAC_LOG_POWER_LEVEL_IS | 28.0 | dBmV (commanded) |
508148.068 | CMAC_LOG_STARTING_RANGING |
|
|
508148.070 | CMAC_LOG_RANGING_BACKOFF_SET | 0 |
|
508148.072 | CMAC_LOG_RNG_REQ_QUEUED | 0 |
|
508148.562 | CMAC_LOG_RNG_REQ_TRANSMITTED |
|
|
508148.566 | CMAC_LOG_RNG_RSP_MSG_RCVD |
|
|
508148.568 | CMAC_LOG_RNG_RSP_SID_ASSIGNED | 2 |
|
508148.570 | CMAC_LOG_ADJUST_RANGING_OFFSET | 2408 |
|
508148.572 | CMAC_LOG_RANGING_OFFSET_SET_TO | 12018 |
|
508148.574 | CMAC_LOG_ADJUST_TX_POWER | 20 |
|
508148.576 | CMAC_LOG_POWER_LEVEL_IS | 33.0 | dBmV (commanded) |
508148.578 | CMAC_LOG_STATE_CHANGE | ranging_2_state | |
508148.580 | CMAC_LOG_RNG_REQ_QUEUED | 2 |
|
508155.820 | CMAC_LOG_RNG_REQ_TRANSMITTED |
|
|
508155.824 | CMAC_LOG_RNG_RSP_MSG_RCVD |
|
|
508155.826 | CMAC_LOG_ADJUST_RANGING_OFFSET |
| |
508155.826 | CMAC_LOG_RANGING_OFFSET_SET_TO | 11954 |
|
508155.828 | CMAC_LOG_RANGING_CONTINUE |
|
|
508165.892 | CMAC_LOG_RNG_REQ_TRANSMITTED |
|
|
508165.894 | CMAC_LOG_RNG_RSP_MSG_RCVD |
|
|
508165.896 | CMAC_LOG_ADJUST_TX_POWER |
| |
508165.898 | CMAC_LOG_POWER_LEVEL_IS | 31.0 | dBmV (commanded) |
508165.900 | CMAC_LOG_RANGING_CONTINUE |
|
|
508175.962 | CMAC_LOG_RNG_REQ_TRANSMITTED |
|
|
508175.964 | CMAC_LOG_RNG_RSP_MSG_RCVD |
|
|
508175.966 | CMAC_LOG_RANGING_SUCCESS |
|
|
Event 5—Establish IP Connectivity
After ranging is complete, the cable interface on the cable access router is UP. Now the cable access router accesses a remote DHCP server to get an IP address. The DHCP server sends a response containing the router IP address plus the TFTP server address, the ToD server address, and the name of
aconfiguration file containing additional configuration parameters. The CMAC_LOG_DHCP_COMPLETE field shows that the IP connectivity was successful.
508175.968 | CMAC_LOG_STATE_CHANGE | dhcp_state |
508176.982 | CMAC_LOG_DHCP_ASSIGNED_IP_ADDRESS | 188.188.1.62 |
508176.984 | CMAC_LOG_DHCP_TFTP_SERVER_ADDRESS | 4.0.0.1 |
508176.986 | CMAC_LOG_DHCP_TOD_SERVER_ADDRESS | 4.0.0.32 |
508176.988 | CMAC_LOG_DHCP_SET_GATEWAY_ADDRESS |
|
508176.988 | CMAC_LOG_DHCP_TZ_OFFSET | 360 |
508176.990 | CMAC_LOG_DHCP_CONFIG_FILE_NAME | platinum.cm |
508176.992 | CMAC_LOG_DHCP_ERROR_ACQUIRING_SEC_SVR_ADDR |
|
508176.996 | CMAC_LOG_DHCP_COMPLETE |
|
Cisco IOS Multiservice Applications Configuration Guide