Cisco Systems MC-607 manual Verifying Routing, MC-644

Page 38

Configuring Subscriber-End Broadband Access Router Features

Configuring Routing

 

Command

Purpose

Step 5

 

 

uBR924(config-router)# network network-number

Specifies the network connected to the cable access

 

 

router on which the RIP process will operate. If the

 

 

cable access router is attached to more than one

 

 

network, enter each IP address in a separate

 

 

command.

Step 6

 

 

uBR924(config-router)# end

Exits router configuration mode.

 

uBR924(config)# interface cable-modem0

Returns to interface configuration mode for the cable

 

 

access router interface.

Step 7

 

 

uBR924(config-if)# ip rip receive v 2

Specifies that only RIP Version 2 packets will be

 

 

received on the coaxial cable interface.

Step 8

 

 

uBR924(config-if)# ip rip send v 2

Specifies that only RIP Version 2 packets will be sent

 

 

on the coaxial cable interface.

Step 9

 

 

uBR924(config-if)# end

Exits interface configuration mode for the cable

 

uBR924(config)# interface ethernet0

access router interface and enters interface

 

 

configuration mode for the Ethernet0 interface.

Step 10

 

 

uBR924(config-if)# no bridge-group 59

Removes the default bridge group assignment from

 

 

the Ethernet0 interface.

Step 11

 

 

uBR924(config-if)# ip rip receive v 2

Specifies that only RIP Version 2 packets will be

 

 

received on this Ethernet interface.

Step 12

 

 

uBR924(config-if)# ip rip send v 2

Specifies that only RIP Version 2 packets will be sent

 

 

on this Ethernet interface.

Step 13

 

 

uBR924(config-if)# Ctrl-z

Returns to privileged EXEC mode.

 

uBR924# copy running-config startup-config Building

Saves the configuration to NVRAM so that it will not

 

configuration...

be lost in the event of a reset, power cycle, or power

 

 

 

 

outage.

 

 

 

Verifying Routing

To verify that bridging is not configured, routing is enabled, and that RIP is configured on the interfaces, enter the show startup-configcommand in privileged EXEC mode:

uBR924# show startup-config

Building configuration...

Current configuration:

!

version 12.1 no service pad

no service password-encryption service udp-small-servers service tcp-small-servers

!

hostname uBR924

!

!

clock timezone - 4 ip subnet-zero

!

!

!

voice-port 0

!

Cisco IOS Multiservice Applications Configuration Guide

MC-644

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Configuring Subscriber-End Broadband Access Router Features MC-607MC-608 Cisco IOS Software Feature SetsSubscriber-end Overview MC-609 Base IP Bridging Feature SetHome Office Easy IP Feature Set MC-610 Small Office Feature SetTelecommuter Feature Set Operating Modes MC-611MC-612 Data SpecificationsDescription Downstream Values Upstream Values Service Assignments MC-613MC-614 Downstream and Upstream Data TransferBridging Applications Routing Applications MC-615Dhcp Server L2TP ProtocolEasy IP Network Address Translation and Port Address TranslationVoice over IP Operations MC-617MC-618 Simplified VoIP over Cable NetworkVoice Compression and Decompression MC-619Protocol Stack MC-620Metric Value Subscriber-End Broadband Access Router Voice SpecificationsSgcp Protocol Stack MC-621Backup Pots Connection MC-622MC-623 Docsis Baseline PrivacyIPSec Network Security NetRanger Support-Cisco IOS Intrusion Detection Triple Data Encryption StandardFirewall MC-624Subscriber-End Broadband Access Router Configuration Options MC-625MC-626 Event Description MC-627Sequence Event Description MC-628MC-629 MC-630 Cable Modem Initialization Flowchart MC-631Subscriber-End Broadband Access Router Basic Troubleshooting MC-632MC-633 WaitforlinkupstateMC-634 UBR924# show controllers cable-modem 0 mac ?MC-635 Event 1-Wait for the Link to Come UpEvent 2-Scan for a Downstream Channel, then Synchronize MC-636 Event 4-Start Ranging for Power AdjustmentsEvent 3-Obtain Upstream Parameters Event 5-Establish IP Connectivity MC-637Event 8-Transfer Operational Parameters Event 6-Establish the Time of DayEvent 7-Establish Security Event 9-Perform RegistrationMC-639 Event 11-Enter the Maintenance StateEvent 10-Comply with Baseline Privacy Subscriber-End Broadband Access Router Configuration Tasks MC-640MC-641 Configuring a Host Name and PasswordCommand Purpose Configuring Ethernet and Cable Access Router Interfaces MC-642Configuring Routing MC-643Verifying Routing MC-644Configuring Bridging MC-645MC-646 Reestablishing DOCSIS-Compliant Bridging MC-647Verifying DOCSIS-Compliant Bridging MC-648MC-649 Customizing the Cable Access Router InterfaceUsing Multiple PCs with the Cable Access Router Basic Internet Access Bridging Configuration Example MC-650Basic Internet Access Routing Configuration Example MC-651IP Multicast Routing Configuration Example MC-652VoIP Bridging Using H.323v2 Configuration Example MC-653VoIP Routing Using H.323v2 Configuration Example MC-654NAT/PAT Configuration Example MC-655VoIP Bridging Using Sgcp Configuration Example MC-656IPSec Configuration Example MC-657L2TP Configuration Example MC-658MC-659 MC-660
Top Page Image Contents