Cisco Systems ASR 901 10G manual Connecting the Chassis Ground and Power

Page 42

Chapter 3 Installing the Cisco ASR 901 10G Router

Mounting the Cisco ASR 901 10G Router

Connecting the Chassis Ground and Power

Before you connect power or turn on power to the Cisco ASR 901 10G router, you must provide an adequate chassis ground (earth) connection to your router.

Grounding the Cisco ASR 901 10G Router

The Cisco ASR 901 10G router provides a grounding point on the rear of the unit for a 2-hole lug.

To ensure the chassis ground connection that you provide is adequate, you need the following parts and tools:

Ratcheting torque screwdriver with Phillips head that exerts up to 15 pound-force inches (lbf-in) of pressure for attaching the ground wire to the router.

Crimping tool as specified by the ground lug manufacturer

16-AWG copper wire for the power cord

Appropriate wire-stripping tools

Caution Before making connections to the Cisco ASR 901 10G router, ensure that you disconnect the power at the circuit breaker. Otherwise it may result in severe injury to yourself, or damage to the router.

Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Warning Use copper conductors only. Statement 1025

Warning When installing the unit, the ground connection must always be made first and disconnected last. Statement 42

 

Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide

3-10

OL-28105-02

Image 42
Contents Cisco Systems, Inc Page N T E N T S Site Environment Formatting Flash Memory as a DOS File System Alarm Port Pinouts B-8 Document Revision History Revision Date Change SummaryOrganization ObjectivesAudience ConventionsSafety Warnings Related DocumentationOL-28105-02 Introduction Hardware DescriptionCisco ASR 901 10G Router-Front View of TDM Version Cisco ASR 901 10G Router-Front View of Ethernet Version Cisco ASR 901 10G Router-Rear View Cisco ASR 901 Router-Front View of Ethernet VersionPower Supply Safety PrecautionsLEDs Specification Value Cisco ASR 901 10G Router AC Power Supply Specifications Environmental Monitoring Temperature Sensor Pin Connector a Connector BSystem Specifications Description SpecificationRouter Interface Numbering Cisco ASR 901 10G Router Regulatory Compliance Interface Number Location LabelChapter Safety Guidelines Safety with EquipmentSafety with Electricity Preventing Electrostatic Discharge Damage Site Planning Power Supply ConsiderationsPrerequisites Site EnvironmentMethod of Procedure Air Flow GuidelinesUnpacking and Checking the Contents of your Shipment Required Tools and EquipmentInstallation Checklist Task Verified byConsole Port Connections Console Port ConsiderationsCreating a Site Log Task Verified by DatePreparing to Install the Router Console Port Considerations OL-28105-02 Installing the Cisco ASR 901 10G Router Network ModulesRack-Mounting Configuration Guidelines Mounting the Cisco ASR 901 10G RouterAttaching Brackets to the Router Rack-Mounting BracketsAttaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks Mounting the Cisco ASR 901 10G Router in a Rack Wall-MountingAttaching Brackets for Wall-Mounting Mounting the Router on a WallUser-supplied screws Connecting the Chassis Ground and Power Grounding the Cisco ASR 901 10G RouterStripping a Ground Wire Power Connection Compliance Wiring the DC-Input Power Source Installing the DC Power Cord Retainer 10 3-Pin Terminal BlockDC power cord Installing the AC Power Cord Retainer 13 Inserting the Retainer through the Lanced LoopSleeve for thin power cords AC power cord Installing and Removing SFP Modules Installing SFP Modules18 SFP Module with a Bale-Clasp Latch Removing SFP Modules Types of RJ-45 Cables Connecting CablesConnecting the Console Port Console PortConnecting the Network Cables Connecting Gigabit Ethernet Interface CablesConnecting T1 and E1 Interface Cables Connecting SFP Cables Connecting Cables to the Bits InterfaceConnecting GPS Cables Connecting to Alarm Port Connecting to the Management Ethernet PortDressing Router Cables Power-On Procedure Powering on the RouterChecklist for Power on Interpreting Front-Panel LEDsFormatting Flash Memory as a DOS File System Formatting Procedures for Flash MemoryFile and Directory Procedures Copying FilesDisplaying Contents of the Flash Memory Deleting Files from the Flash MemoryDisplaying File Content Enter a Directory and Determine the Current DirectoryWhat to Do After Installing the Hardware Troubleshooting Problem SolvingTroubleshooting the Power and Cooling Systems Environmental Reporting FeaturesSymptom Possible Cause Corrective Action Troubleshooting Cables and Connections Information Packet publicationReading the LEDs Chassis LEDsColor/State Location Description 10G SFP+ Ethernet Interface LEDs T1/E1 Interface LEDsSFP Ethernet Interface LEDs Color/State Description two LEDs for each T1/E1 portRJ-45 Ethernet Interface LEDs Cable Specifications Gigabit Ethernet Connector PinoutsSFP and SFP+ Port Pinouts and Cable Specifications Pin FE Signal GE SignalT1/E1 Port Pinouts Console Port Signals and Pinouts Pin Signal Name Direction DescriptionConsole Port Signals and Pinouts Pin Signal Name HP Pins Direction DescriptionRJ-45-to-DB-9 Terminal Adapter Console Terminal Adapter Device Signal RJ-45 Pin DB-25 Pin Identifying a Rollover CableConsole RJ-45-to-DB-25 Port DTE Bits Port Pinouts Time of Day PinoutsGPS Port Pinouts 10 MhzAlarm Port Pinouts Pin Signal Name DescriptionManagement Ethernet Port Pinouts Auxiliary PortOL-28105-02 Site Log Date InitialsNumerics IN-2 IN-3 IN-4