Cisco Systems ASR 901 10G manual Sleeve for thin power cords AC power cord

Page 48

Chapter 3 Installing the Cisco ASR 901 10G Router

Mounting the Cisco ASR 901 10G Router

1	AC power cord	2	Smaller sleeve for thin power cords

3	Latch	4	—

Step 4 Slide the retainer through the other latches to lock it. See Figure 3-15.

Figure 3-15 Locking the Retainer

334522

3

2

1

(

1

3

AC power cord

2 Sleeve for thin power cords

Latches

Step 5 (Optional) Use the small sleeve for thin power cords. Use the small sleeve to provide greater stability for thin cords. Detach the sleeve, and slide it over the power cord. See Figure 3-16.

Figure 3-16 Sleeve Around the Power Cord

2

1	1

208987

1

Sleeve for thin power cords

2

AC power cord

	Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide
3-16	OL-28105-02

Image 48

Contents Cisco Systems, Inc Page N T E N T S Site Environment Formatting Flash Memory as a DOS File System Alarm Port Pinouts B-8 Document Revision History Revision Date Change SummaryObjectives AudienceOrganization ConventionsSafety Warnings Related DocumentationOL-28105-02 Introduction Hardware DescriptionCisco ASR 901 10G Router-Front View of TDM Version Cisco ASR 901 10G Router-Front View of Ethernet Version Cisco ASR 901 10G Router-Rear View Cisco ASR 901 Router-Front View of Ethernet VersionPower Supply Safety PrecautionsLEDs Specification Value Cisco ASR 901 10G Router AC Power Supply Specifications Environmental Monitoring Temperature Sensor Pin Connector a Connector BSystem Specifications Description SpecificationRouter Interface Numbering Cisco ASR 901 10G Router Regulatory Compliance Interface Number Location LabelChapter Safety Guidelines Safety with EquipmentSafety with Electricity Preventing Electrostatic Discharge Damage Power Supply Considerations PrerequisitesSite Planning Site EnvironmentMethod of Procedure Air Flow GuidelinesUnpacking and Checking the Contents of your Shipment Required Tools and EquipmentInstallation Checklist Task Verified byConsole Port Considerations Creating a Site LogConsole Port Connections Task Verified by DatePreparing to Install the Router Console Port Considerations OL-28105-02 Installing the Cisco ASR 901 10G Router Network ModulesRack-Mounting Configuration Guidelines Mounting the Cisco ASR 901 10G RouterAttaching Brackets to the Router Rack-Mounting BracketsAttaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks Mounting the Cisco ASR 901 10G Router in a Rack Wall-MountingAttaching Brackets for Wall-Mounting Mounting the Router on a WallUser-supplied screws Connecting the Chassis Ground and Power Grounding the Cisco ASR 901 10G RouterStripping a Ground Wire Power Connection Compliance Wiring the DC-Input Power Source Installing the DC Power Cord Retainer 10 3-Pin Terminal BlockDC power cord Installing the AC Power Cord Retainer 13 Inserting the Retainer through the Lanced LoopSleeve for thin power cords AC power cord Installing and Removing SFP Modules Installing SFP Modules18 SFP Module with a Bale-Clasp Latch Removing SFP Modules Connecting Cables Connecting the Console PortTypes of RJ-45 Cables Console PortConnecting the Network Cables Connecting Gigabit Ethernet Interface CablesConnecting T1 and E1 Interface Cables Connecting SFP Cables Connecting Cables to the Bits InterfaceConnecting GPS Cables Connecting to Alarm Port Connecting to the Management Ethernet PortDressing Router Cables Powering on the Router Checklist for Power onPower-On Procedure Interpreting Front-Panel LEDsFormatting Procedures for Flash Memory File and Directory ProceduresFormatting Flash Memory as a DOS File System Copying FilesDisplaying Contents of the Flash Memory Deleting Files from the Flash MemoryDisplaying File Content Enter a Directory and Determine the Current DirectoryWhat to Do After Installing the Hardware Troubleshooting Problem SolvingTroubleshooting the Power and Cooling Systems Environmental Reporting FeaturesSymptom Possible Cause Corrective Action Troubleshooting Cables and Connections Information Packet publicationReading the LEDs Chassis LEDsColor/State Location Description T1/E1 Interface LEDs SFP Ethernet Interface LEDs10G SFP+ Ethernet Interface LEDs Color/State Description two LEDs for each T1/E1 portRJ-45 Ethernet Interface LEDs Cable Specifications Gigabit Ethernet Connector PinoutsSFP and SFP+ Port Pinouts and Cable Specifications Pin FE Signal GE SignalT1/E1 Port Pinouts Console Port Signals and Pinouts Pin Signal Name Direction DescriptionConsole Port Signals and Pinouts Pin Signal Name HP Pins Direction DescriptionRJ-45-to-DB-9 Terminal Adapter Console Terminal Adapter Device Signal RJ-45 Pin DB-25 Pin Identifying a Rollover CableConsole RJ-45-to-DB-25 Port DTE Bits Port Pinouts Time of Day PinoutsGPS Port Pinouts 10 MhzAlarm Port Pinouts Pin Signal Name DescriptionManagement Ethernet Port Pinouts Auxiliary PortOL-28105-02 Site Log Date InitialsNumerics IN-2 IN-3 IN-4