Cisco Systems ASR 901 10G manual Installation Checklist, Task Verified by

Page 29

Chapter 2 Preparing to Install the Router

Site Planning

Warning Only trained and qualified personnel should be allowed to install or replace this equipment.

Statement 49

•ESD-preventive cord and wrist strap.

•Number 2 Phillips screwdriver.

•Flat-blade screwdrivers: small, 3/16-inch (0.476 cm) and medium, 1/4-inch (0.625 cm).

–To install or remove modules

–To remove the cover, if you are upgrading memory or other components

•Number 12-24 pan-head screws to secure the router to the equipment rack.

•Cables for WAN and LAN port connections (depending on the configuration).

Note For more information on cable specifications, see Appendix B, “Cable Specifications”

•Ethernet hub or PC with a network interface card for connection to the Ethernet (LAN) ports.

•Console terminal (an ASCII terminal or a PC running terminal emulation software), which is configured for 9600 baud, 8 data bits, no parity, and 2 stop bits.

•Console cable for connection to the console port.

•Ratcheting torque screwdriver with a Phillips head that exerts up to 15 pound-force inches (lbf-in) of pressure.

•Crimping tool as specified by the ground lug manufacturer.

•16-AWG copper wire for the power cord.

•Wire-stripping tools for stripping both the 6-AWG and 18-AWG wires.

•Serial interfaces may require a channel service unit or a data service unit (CSU/DSU).

Installation Checklist

To assist you with your installation and to provide a historical record of completed tasks and users, use the following installation checklist. Make a copy of this checklist and mark the entries as you complete each task. When the checklist is completed, include a copy of the checklist for each router in your site log along with other records for your new router. See Appendix C, “Site Log” for information on the site log, including a sample site log.

Installation Checklist for Site:

Router Name:

Task

Verified by

Date

Installation checklist copied

Background information placed in site log

Site power voltages verified

Installation site power check completed

Required tools available

Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide

	OL-28105-02	2-7

Image 29

Contents Cisco Systems, Inc Page N T E N T S Site Environment Formatting Flash Memory as a DOS File System Alarm Port Pinouts B-8 Revision Date Change Summary Document Revision HistoryAudience ObjectivesOrganization ConventionsRelated Documentation Safety WarningsOL-28105-02 Hardware Description IntroductionCisco ASR 901 10G Router-Front View of TDM Version Cisco ASR 901 10G Router-Front View of Ethernet Version Cisco ASR 901 Router-Front View of Ethernet Version Cisco ASR 901 10G Router-Rear ViewLEDs Power SupplySafety Precautions Specification Value Cisco ASR 901 10G Router AC Power Supply Specifications Pin Connector a Connector B Environmental Monitoring Temperature SensorRouter Interface Numbering System SpecificationsDescription Specification Cisco ASR 901 10G Router Interface Number Location Label Regulatory ComplianceChapter Safety with Equipment Safety GuidelinesSafety with Electricity Preventing Electrostatic Discharge Damage Prerequisites Power Supply ConsiderationsSite Planning Site EnvironmentAir Flow Guidelines Method of ProcedureRequired Tools and Equipment Unpacking and Checking the Contents of your ShipmentTask Verified by Installation ChecklistCreating a Site Log Console Port ConsiderationsConsole Port Connections Task Verified by DatePreparing to Install the Router Console Port Considerations OL-28105-02 Network Modules Installing the Cisco ASR 901 10G RouterMounting the Cisco ASR 901 10G Router Rack-Mounting Configuration GuidelinesRack-Mounting Brackets Attaching Brackets to the RouterAttaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks Wall-Mounting Mounting the Cisco ASR 901 10G Router in a RackMounting the Router on a Wall Attaching Brackets for Wall-MountingUser-supplied screws Grounding the Cisco ASR 901 10G Router Connecting the Chassis Ground and PowerStripping a Ground Wire Power Connection Compliance Wiring the DC-Input Power Source 10 3-Pin Terminal Block Installing the DC Power Cord RetainerDC power cord 13 Inserting the Retainer through the Lanced Loop Installing the AC Power Cord RetainerSleeve for thin power cords AC power cord Installing SFP Modules Installing and Removing SFP Modules18 SFP Module with a Bale-Clasp Latch Removing SFP Modules Connecting the Console Port Connecting CablesTypes of RJ-45 Cables Console PortConnecting T1 and E1 Interface Cables Connecting the Network CablesConnecting Gigabit Ethernet Interface Cables Connecting GPS Cables Connecting SFP CablesConnecting Cables to the Bits Interface Dressing Router Cables Connecting to Alarm PortConnecting to the Management Ethernet Port Checklist for Power on Powering on the RouterPower-On Procedure Interpreting Front-Panel LEDsFile and Directory Procedures Formatting Procedures for Flash MemoryFormatting Flash Memory as a DOS File System Copying FilesDeleting Files from the Flash Memory Displaying Contents of the Flash MemoryEnter a Directory and Determine the Current Directory Displaying File ContentWhat to Do After Installing the Hardware Problem Solving TroubleshootingSymptom Possible Cause Corrective Action Troubleshooting the Power and Cooling SystemsEnvironmental Reporting Features Information Packet publication Troubleshooting Cables and ConnectionsColor/State Location Description Reading the LEDsChassis LEDs SFP Ethernet Interface LEDs T1/E1 Interface LEDs10G SFP+ Ethernet Interface LEDs Color/State Description two LEDs for each T1/E1 portRJ-45 Ethernet Interface LEDs Gigabit Ethernet Connector Pinouts Cable SpecificationsT1/E1 Port Pinouts SFP and SFP+ Port Pinouts and Cable SpecificationsPin FE Signal GE Signal Pin Signal Name Direction Description Console Port Signals and PinoutsRJ-45-to-DB-9 Terminal Adapter Console Console Port Signals and PinoutsPin Signal Name HP Pins Direction Description Console RJ-45-to-DB-25 Port DTE Terminal Adapter Device Signal RJ-45 Pin DB-25 PinIdentifying a Rollover Cable Time of Day Pinouts Bits Port Pinouts10 Mhz GPS Port PinoutsPin Signal Name Description Alarm Port PinoutsAuxiliary Port Management Ethernet Port PinoutsOL-28105-02 Site Log Initials DateNumerics IN-2 IN-3 IN-4