Cisco Systems ASR 901 10G Troubleshooting Cables and Connections, Information Packet publication

Page 63

Appendix A Troubleshooting

Problem Solving

Table A-2

Interpreting Environmental Reporting Features

 

 

 

 

 

Symptom

 

Possible Cause

Corrective Action

 

 

 

The router operates at an

There is a fan failure.

Take corrective steps. For

abnormally high temperature.

There is an air conditioner

information about environmental

The following message appears

operating conditions, see the

failure in the room.

on the console screen:

System Specifications, page 1-9).

The air flow to cooling vents is

%SYS-1-OVERTEMP: System

 

blocked.

 

detected OVERTEMPERATURE

 

 

 

condition. Please resolve

 

 

cooling problem immediately!

 

 

 

 

 

 

Troubleshooting Cables and Connections

Network problems can be caused by a cable or cable connection, or external device such as a modem, transceiver, hub, wall jack, WAN interface, or terminal. See Table A-3for information to help you isolate the problem.

Table A-3

Troubleshooting Cables, and Connections

 

 

 

 

 

Symptom

 

Possible Cause

Corrective Action

 

 

 

The router is experiencing

The router does not boot

Check the router chassis or

network problems.

properly.

software. For warranty

 

 

The router constantly or

information, refer to the Cisco

 

 

Information Packet publication

 

 

intermittently reboots.

 

 

that shipped with your router or

 

 

 

 

 

 

contact customer service.

 

 

 

 

 

 

The router boots, but the console

Verify that the parameters for

 

 

screen is frozen.

your terminal are set as follows:

 

 

 

 

 

(a) The terminal should have

 

 

 

the same data rate as the

 

 

 

router (9600 bps is the

 

 

 

default).

 

 

 

(b) 8 data bits.

 

 

 

(c) No parity generated or

 

 

 

checked.

 

 

 

(d) 2 stop bits.

 

 

 

 

 

 

The router powers on and boots

There may be a problem with the

 

 

only when a particular cable is

module or cable. For warranty

 

 

 

 

disconnected.

information, refer to the Cisco

 

 

 

Information Packet publication

 

 

 

that shipped with your order or

 

 

 

contact customer service.

 

 

 

 

Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide

 

OL-28105-02

A-3

 

Image 63
Contents Cisco Systems, Inc Page N T E N T S Site Environment Formatting Flash Memory as a DOS File System Alarm Port Pinouts B-8 Revision Date Change Summary Document Revision HistoryConventions ObjectivesAudience OrganizationRelated Documentation Safety WarningsOL-28105-02 Hardware Description IntroductionCisco ASR 901 10G Router-Front View of TDM Version Cisco ASR 901 10G Router-Front View of Ethernet Version Cisco ASR 901 Router-Front View of Ethernet Version Cisco ASR 901 10G Router-Rear ViewPower Supply Safety PrecautionsLEDs Specification Value Cisco ASR 901 10G Router AC Power Supply Specifications Pin Connector a Connector B Environmental Monitoring Temperature SensorSystem Specifications Description SpecificationRouter Interface Numbering Cisco ASR 901 10G Router Interface Number Location Label Regulatory ComplianceChapter Safety with Equipment Safety GuidelinesSafety with Electricity Preventing Electrostatic Discharge Damage Site Environment Power Supply ConsiderationsPrerequisites Site PlanningAir Flow Guidelines Method of ProcedureRequired Tools and Equipment Unpacking and Checking the Contents of your ShipmentTask Verified by Installation ChecklistTask Verified by Date Console Port ConsiderationsCreating a Site Log Console Port ConnectionsPreparing to Install the Router Console Port Considerations OL-28105-02 Network Modules Installing the Cisco ASR 901 10G RouterMounting the Cisco ASR 901 10G Router Rack-Mounting Configuration GuidelinesRack-Mounting Brackets Attaching Brackets to the RouterAttaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks Wall-Mounting Mounting the Cisco ASR 901 10G Router in a RackMounting the Router on a Wall Attaching Brackets for Wall-MountingUser-supplied screws Grounding the Cisco ASR 901 10G Router Connecting the Chassis Ground and PowerStripping a Ground Wire Power Connection Compliance Wiring the DC-Input Power Source 10 3-Pin Terminal Block Installing the DC Power Cord RetainerDC power cord 13 Inserting the Retainer through the Lanced Loop Installing the AC Power Cord RetainerSleeve for thin power cords AC power cord Installing SFP Modules Installing and Removing SFP Modules18 SFP Module with a Bale-Clasp Latch Removing SFP Modules Console Port Connecting CablesConnecting the Console Port Types of RJ-45 CablesConnecting the Network Cables Connecting Gigabit Ethernet Interface CablesConnecting T1 and E1 Interface Cables Connecting SFP Cables Connecting Cables to the Bits InterfaceConnecting GPS Cables Connecting to Alarm Port Connecting to the Management Ethernet PortDressing Router Cables Interpreting Front-Panel LEDs Powering on the RouterChecklist for Power on Power-On ProcedureCopying Files Formatting Procedures for Flash MemoryFile and Directory Procedures Formatting Flash Memory as a DOS File SystemDeleting Files from the Flash Memory Displaying Contents of the Flash MemoryEnter a Directory and Determine the Current Directory Displaying File ContentWhat to Do After Installing the Hardware Problem Solving TroubleshootingTroubleshooting the Power and Cooling Systems Environmental Reporting FeaturesSymptom Possible Cause Corrective Action Information Packet publication Troubleshooting Cables and ConnectionsReading the LEDs Chassis LEDsColor/State Location Description Color/State Description two LEDs for each T1/E1 port T1/E1 Interface LEDsSFP Ethernet Interface LEDs 10G SFP+ Ethernet Interface LEDsRJ-45 Ethernet Interface LEDs Gigabit Ethernet Connector Pinouts Cable SpecificationsSFP and SFP+ Port Pinouts and Cable Specifications Pin FE Signal GE SignalT1/E1 Port Pinouts Pin Signal Name Direction Description Console Port Signals and PinoutsConsole Port Signals and Pinouts Pin Signal Name HP Pins Direction DescriptionRJ-45-to-DB-9 Terminal Adapter Console Terminal Adapter Device Signal RJ-45 Pin DB-25 Pin Identifying a Rollover CableConsole RJ-45-to-DB-25 Port DTE Time of Day Pinouts Bits Port Pinouts10 Mhz GPS Port PinoutsPin Signal Name Description Alarm Port PinoutsAuxiliary Port Management Ethernet Port PinoutsOL-28105-02 Site Log Initials DateNumerics IN-2 IN-3 IN-4