Craftsman 315.21211 owner manual Miter Lock Handle, Tighten Control ARM Miter Toinstall Blade

Page 13

_k WARNING: To prevent accidental starting that could cause possible serious personal injury,

assemble all parts to your saw before connecting it to power supply. Saw should never be connected to power supply when you are assembling parts, making adjustments, installing or removing blades, or when not in use.

As mentioned previously your saw has been factory assembled and adjusted. The miter lock handle, dust

guide, and blade are the only parts that have to be installed.

MITER LOCK HANDLE

See Figure 8.

To install the miter lock handle, place the threaded stud on the end of the miter lock handle into the threaded hole in the control arm. Turn clockwise to tighten.

LOOSEN

TIGHTEN

CONTROL

ARM

MITER

TOINSTALL BLADE

See Figures 10, 11, and 12.

A WARNING: A 10 in. blade is the maximum blade capacity of your saw. Never use a blade that is too thick to allow outer blade washer to

engage with the flats on the spindle. Larger blades will come in contact with the blade

guards, while thicker blades will prevent the blade screw from securingthe btade on the spindle. Either of these situationscould result in

aserious accident and can cause serious personal injury.

•Unplug your saw.

_ WARNING: Failure to unplug your saw could result in accidental starting causing possible serious personal injury.

Push down on the saw arm and pull out the lock pin to release saw arm. Raise saw arm to its full

raised position. Be cautious, saw arm is spring loaded to raise.

•Loosen the phillips screw on the blade bolt cover until blade bolt cover can be raised.

See Figure lO and 11.

•Gently raise the lower blade guard bracket, releasing lower blade guard from notch so that lower blade guard and blade bolt cover can be rotated up and back to expose the blade bolt. See Figures 10 and 11.

PHILLIPSSCREW

MITERTABLE LOCKHANDLE

DUST GUIDE

See Figure 9.

Fig. 8

LOWER

BLADEGUARD

To install the dust guide, place the end marked INSERT over the exhaust port in the upper blade

guard. Turn the guide so that the open end is facing down or toward the rear of the saw.

EXHAUST

PORT

DUSTGUIDE

Fig. 9

LOWERBLADE

GUARD BRACKET

Fig. 10

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents OwnersManual Full ONE Year Warranty Double Insulation Symbolmeaning Safety Alert SymbolRead ALL Instructions Do not USE in Dangerous EnvironRules for Safe Operation Always Wear Safety Glasses withDo not Remove the Sawsblade Always USE a Clamp to secure the work Rules for Safe OperationThrow-Back ArborThrough Sawing Blade Diameter Arbor No Load Speed Inch Compound Miter Saw MmHEXKEY BladewrenchDustguide FramingsquareAMP Motor Know Your Compound Miter SAWCutting Capacities Miter Lock Handle Carrying HandleLOCK-OFF Lever Spindle Lock ButtonBevel Lock Knob Positive Stops on Miter TableElectric Brake SELF-RETRACTING Lower Blade GuardMiter Lock Handle Tighten Control ARM Miter Toinstall BladePhillipsscrew Mitertable Lockhandle Dust Guide Boltcover On Spindle Innerblade Washerwh Lowerphillips BladeguardscrewBlade Tighten Literbladewasher Withdouble D Flats BladeboltTo the Fence Squaring the Miter TableMmSOCKET Squaring the SAW Blade to the FenceHeadscrew Mounting Miter Bracket WrenchSquaring the Blade to TABLE,ADJUSTMENTSAREREQUIREDMiter Table Fence Combination Miter SquareBevel Pivot Adjustment Pivot AdjustmentsDepth Stop Adjustments Cutting a Slot in the Zero Clearance Throat PlateTo Crosscut with Your Miter SAW Cutting with Your Compound Miter SAW CrosscuttingTo Bevel CUT with Your Miter SAW Leftside Rightside Indicator Point Scalescale MounngbracketStraight Crosscut Bevel CUTCuts Compound Miter CUTCompound Mitercut To Make a Compound CUT with Your Miter SAWBefore turning on the saw, perform a dry run Support Long WorkpiecesSag, The support should let the werkpiece lay flat on LongworkpieceCutting Compound Miters OfsideLaying Molding Flat on Cutting Crown MoldingClamping Wide Workpieces Cutting Warped MaterialWrong Wide BoardLubrication GeneralExtension Cords Assembly Fig Brush ReplacementBrush Brush CAPPage Rf- J =- ,- J ¢ Page Soooo,-o Ul el O00 ILl O 9 9 9 9 9 HomeCentralsM

315.21211 specifications

The Craftsman 315.21211 is a versatile power tool known for its robust design and exceptional performance. This model, primarily aimed at both professionals and DIY enthusiasts, boasts a range of features that make it an essential addition to any workshop or toolset.

One of the main features of the Craftsman 315.21211 is its powerful motor, designed to deliver consistent performance even under heavy loads. This motor allows for efficient cutting, drilling, and fastening, making it suitable for a variety of applications. The tool's high RPM rating enables it to handle tough materials like hardwood, metal, and plastic with ease, ensuring clean and precise results.

The ergonomic design of the Craftsman 315.21211 enhances user comfort during extended use. The rubberized grip reduces vibrations and improves control, thus minimizing fatigue. Additionally, the tool is relatively lightweight, which contributes to easier handling and maneuverability, especially in tight or awkward spaces.

Another significant aspect of the Craftsman 315.21211 is its inclusion of advanced technology features. The tool often comes equipped with a built-in LED light that illuminates the work area, making it easier to work in dimly lit conditions. This feature is particularly useful for tasks that require precision and attention to detail.

The versatility of the Craftsman 315.21211 is evidenced by its compatibility with various attachments and accessories. Whether you need to drill a hole, drive screws, or perform complex cutting tasks, this model adapts seamlessly to different functions. The quick-change chuck mechanism allows for easy swapping of bits, ensuring that users can transition between tasks quickly.

Safety is also a priority with the Craftsman 315.21211. The tool includes a safety lock feature that prevents accidental activation, providing peace of mind during operation. This thoughtful design element is essential for both seasoned users and those new to power tools.

In summary, the Craftsman 315.21211 stands out for its powerful motor, ergonomic design, advanced technology features, and versatility. These characteristics make it an invaluable tool for anyone looking to tackle a wide range of projects with confidence and ease. Whether you are a professional contractor or a weekend DIY warrior, the Craftsman 315.21211 promises to deliver reliability and exceptional performance in all your endeavors.
Top Page Image Contents