Craftsman 315.21211 Support Long Workpieces, Before turning on the saw, perform a dry run

Page 23

•Before turning on the saw, perform a dry run of the

cutting operation just to make sure that no problems will occur when the cut is made.

•Grasp the saw handle firmly, press the lock-off tab down, then squeeze the switch trigger. Allow sev- eral seconds for the blade to reach maximum speed.

•Slowly lower the blade into and through the workpiece. See Figures 29 and 30.

•Release the switch trigger and allow the saw blade to stop rotating before raising the blade out of workpiece. Wait until the electric brake stops blade

from turning before removing the workpiece from miter table.

SUPPORT LONG WORKPIECES

See Figure 31.

Long workpieces need extra supports. Supports

should be placed along the workpiece so it does net

sag, The support should let the werkpiece lay flat on

the base of the saw and work table during the cutting

operation, Use the optional work clamp or a C-clamp to secure the workpiece.

_1, WARNING: To avoid serious personal injury, always keep your hands outside the no hands

zone; at least 3 in. from blade. Never perform any cutting operation freehand (without holding workpiece against the fence). The blade could grab the workpiece if it slips or twists.

LONGWORKPIECE

WORKPIECE SUPPORTS

45° X 45° COMPOUNDMITERCUT

Fig. 30

Fig. 31

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents OwnersManual Full ONE Year Warranty Do not USE in Dangerous Environ Symbolmeaning Safety Alert SymbolDouble Insulation Read ALL InstructionsDo not Remove the Sawsblade Always Wear Safety Glasses withRules for Safe Operation Always USE a Clamp to secure the work Rules for Safe OperationThrough Sawing ArborThrow-Back Blade Diameter Arbor No Load Speed Inch Compound Miter Saw Framingsquare BladewrenchMmHEXKEY DustguideCutting Capacities Know Your Compound Miter SAWAMP Motor Spindle Lock Button Carrying HandleMiter Lock Handle LOCK-OFF LeverSELF-RETRACTING Lower Blade Guard Positive Stops on Miter TableBevel Lock Knob Electric BrakePhillipsscrew Mitertable Lockhandle Dust Guide Tighten Control ARM Miter Toinstall BladeMiter Lock Handle Tighten Literbladewasher Withdouble D Flats Bladebolt Lowerphillips BladeguardscrewBoltcover On Spindle Innerblade Washerwh BladeTo the Fence Squaring the Miter TableBracket Wrench Squaring the SAW Blade to the FenceMmSOCKET Headscrew Mounting MiterFence Combination Miter Square TABLE,ADJUSTMENTSAREREQUIREDSquaring the Blade to Miter TableCutting a Slot in the Zero Clearance Throat Plate Pivot AdjustmentsBevel Pivot Adjustment Depth Stop AdjustmentsTo Crosscut with Your Miter SAW Cutting with Your Compound Miter SAW CrosscuttingBevel CUT Leftside Rightside Indicator Point Scalescale MounngbracketTo Bevel CUT with Your Miter SAW Straight CrosscutCuts Compound Miter CUTCompound Mitercut To Make a Compound CUT with Your Miter SAWLongworkpiece Support Long WorkpiecesBefore turning on the saw, perform a dry run Sag, The support should let the werkpiece lay flat onCutting Compound Miters OfsideLaying Molding Flat on Cutting Crown MoldingWide Board Cutting Warped MaterialClamping Wide Workpieces WrongExtension Cords GeneralLubrication Brush CAP Brush ReplacementAssembly Fig BrushPage Rf- J =- ,- J ¢ Page Soooo,-o Ul el O00 ILl O 9 9 9 9 9 HomeCentralsM

315.21211 specifications

The Craftsman 315.21211 is a versatile power tool known for its robust design and exceptional performance. This model, primarily aimed at both professionals and DIY enthusiasts, boasts a range of features that make it an essential addition to any workshop or toolset.

One of the main features of the Craftsman 315.21211 is its powerful motor, designed to deliver consistent performance even under heavy loads. This motor allows for efficient cutting, drilling, and fastening, making it suitable for a variety of applications. The tool's high RPM rating enables it to handle tough materials like hardwood, metal, and plastic with ease, ensuring clean and precise results.

The ergonomic design of the Craftsman 315.21211 enhances user comfort during extended use. The rubberized grip reduces vibrations and improves control, thus minimizing fatigue. Additionally, the tool is relatively lightweight, which contributes to easier handling and maneuverability, especially in tight or awkward spaces.

Another significant aspect of the Craftsman 315.21211 is its inclusion of advanced technology features. The tool often comes equipped with a built-in LED light that illuminates the work area, making it easier to work in dimly lit conditions. This feature is particularly useful for tasks that require precision and attention to detail.

The versatility of the Craftsman 315.21211 is evidenced by its compatibility with various attachments and accessories. Whether you need to drill a hole, drive screws, or perform complex cutting tasks, this model adapts seamlessly to different functions. The quick-change chuck mechanism allows for easy swapping of bits, ensuring that users can transition between tasks quickly.

Safety is also a priority with the Craftsman 315.21211. The tool includes a safety lock feature that prevents accidental activation, providing peace of mind during operation. This thoughtful design element is essential for both seasoned users and those new to power tools.

In summary, the Craftsman 315.21211 stands out for its powerful motor, ergonomic design, advanced technology features, and versatility. These characteristics make it an invaluable tool for anyone looking to tackle a wide range of projects with confidence and ease. Whether you are a professional contractor or a weekend DIY warrior, the Craftsman 315.21211 promises to deliver reliability and exceptional performance in all your endeavors.
Top Page Image Contents