Craftsman 315.21211 owner manual Rules for Safe Operation, Always USE a Clamp to secure the work

Page 5

RULES FOR SAFE OPERATION (Continued)

ALWAYS SUPPORT LONG WORKPIECES to

minimize risk of blade pinching and kickback, Saw may slip, walk, or slide while cutting long or heavy boards.

BEFORE MAKING A CUT, BE SURE ALL

ADJUSTMENTS ARE SECURE.

AVOID CUTTING NAILS. Inspect for and

remove all nails from lumber before cutting.

ALWAYS USE A CLAMP to secure the work-

piece when possible.

•NEVER TOUCH BLADE or other moving parts during use.

•NEVER START A TOOL WHEN THE BLADE IS IN CONTACT WITH WORKPIECE. Allow motor to come up to full speed before starting cut.

•MAKE SURE THE MITER TABLE AND SAW

ARM (BEVEL FUNCTION) ARE LOCKED IN POSITION BEFORE OPERATING YOUR SAW.

Lock the miter table by securely tightening the miter lock handle. Lock the saw arm (bevel function) by securely tightening the bevel lock knob.

NEVER USE A LENGTH STOP ON THE FREE SCRAP END OF A CLAMPED WORKPIECE. NEVER hold onto or bind the free scrap end of the workpiece in any operation. If a work clamp and length stop are used together, they must both be installed on the same side of the saw table to prevent the saw from catching the loose end and kicking up

NEVER cut more than one piece at a time. DO NOT STACK more than one workpiece on the saw table at a time.

•NEVER PERFORM ANY OPERATION "FREE- HAND". Always place the workpiece to be cut on the miter table and position it firmly against the fence as a backstop. Always use the fence.

•NEVER hand hold a workpiece that is too small to be clamped. Keep hands clear of the no hands zone.

NEVER reach behind, under, or within three inches of the blade and its cutting path with your hands and fingers for any reason.

NEVER reach to pick up a workpiece, a piece of scrap, or anything else that is in or near the cutting path of the blade.

•AVOID AWKWARD OPERATIONS AND HAND

POSITIONS where a sudden slip could cause your hand to move into the blade. ALWAYS make sure you have good balance. NEVER operate your miter saw on the floor or in a crouched position.

•NEVER stand or have any part of your body in line with the path of the saw blade.

•ALWAYS release the power switch and allow the saw blade to stop rotating before raising it out of the workpiece.

•DO NOT TURN THE MOTOR SWITCH ON AND OFF RAPIDLY. This could cause the saw blade to loosen and could create a hazard. Should this ever occur, stand clear and allow the saw blade to come to a complete stop. Disconnect your saw from the power supply and securely retighten the blade bolt.

REPLACEMENT PARTS. Allrepairs, whether electrical or mechanical, should be made by qualified service technician at a Sears store.

A WARNING: When servicing use only identical Craftsman replacement parts. Use of any other parts may create a hazard or cause product damage.

•NEVER USE IN AN EXPLOSIVE ATMO- SPHERE. Normal sparking of the motor could ignite fumes.

•NEVER leave the miter saw unattended while connected to a power source.

•POLARIZED PLUGS. To reduce the risk of electric shock, this tool has a polarized plug (one

blade is wider than the other ) . This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

•IF ANY PART OF THIS MITER SAW IS MISS- ING or should break, bend, or fail in any way, or should any electrical component fail to perform properly, shut off the power switch, remove the miter saw plug from the power source and have damaged, missing, or failed parts replaced before resuming operation.

•DO NOT OPERATE THIS TOOL WHILE UN- DER THE INFLUENCE OF DRUGS, ALCOHOL, OR ANY MEDICATION.

Page 4 Page 6
Image 5
Page 4 Page 6
Contents OwnersManual Full ONE Year Warranty Double Insulation Symbolmeaning Safety Alert SymbolRead ALL Instructions Do not USE in Dangerous EnvironDo not Remove the Sawsblade Always Wear Safety Glasses withRules for Safe Operation Always USE a Clamp to secure the work Rules for Safe OperationThrough Sawing ArborThrow-Back Blade Diameter Arbor No Load Speed Inch Compound Miter Saw MmHEXKEY BladewrenchDustguide FramingsquareCutting Capacities Know Your Compound Miter SAWAMP Motor Miter Lock Handle Carrying HandleLOCK-OFF Lever Spindle Lock ButtonBevel Lock Knob Positive Stops on Miter TableElectric Brake SELF-RETRACTING Lower Blade GuardPhillipsscrew Mitertable Lockhandle Dust Guide Tighten Control ARM Miter Toinstall BladeMiter Lock Handle Boltcover On Spindle Innerblade Washerwh Lowerphillips BladeguardscrewBlade Tighten Literbladewasher Withdouble D Flats BladeboltTo the Fence Squaring the Miter TableMmSOCKET Squaring the SAW Blade to the FenceHeadscrew Mounting Miter Bracket WrenchSquaring the Blade to TABLE,ADJUSTMENTSAREREQUIREDMiter Table Fence Combination Miter SquareBevel Pivot Adjustment Pivot AdjustmentsDepth Stop Adjustments Cutting a Slot in the Zero Clearance Throat PlateTo Crosscut with Your Miter SAW Cutting with Your Compound Miter SAW CrosscuttingTo Bevel CUT with Your Miter SAW Leftside Rightside Indicator Point Scalescale MounngbracketStraight Crosscut Bevel CUTCuts Compound Miter CUTCompound Mitercut To Make a Compound CUT with Your Miter SAWBefore turning on the saw, perform a dry run Support Long WorkpiecesSag, The support should let the werkpiece lay flat on LongworkpieceCutting Compound Miters OfsideLaying Molding Flat on Cutting Crown MoldingClamping Wide Workpieces Cutting Warped MaterialWrong Wide BoardExtension Cords GeneralLubrication Assembly Fig Brush ReplacementBrush Brush CAPPage Rf- J =- ,- J ¢ Page Soooo,-o Ul el O00 ILl O 9 9 9 9 9 HomeCentralsM

315.21211 specifications

The Craftsman 315.21211 is a versatile power tool known for its robust design and exceptional performance. This model, primarily aimed at both professionals and DIY enthusiasts, boasts a range of features that make it an essential addition to any workshop or toolset.

One of the main features of the Craftsman 315.21211 is its powerful motor, designed to deliver consistent performance even under heavy loads. This motor allows for efficient cutting, drilling, and fastening, making it suitable for a variety of applications. The tool's high RPM rating enables it to handle tough materials like hardwood, metal, and plastic with ease, ensuring clean and precise results.

The ergonomic design of the Craftsman 315.21211 enhances user comfort during extended use. The rubberized grip reduces vibrations and improves control, thus minimizing fatigue. Additionally, the tool is relatively lightweight, which contributes to easier handling and maneuverability, especially in tight or awkward spaces.

Another significant aspect of the Craftsman 315.21211 is its inclusion of advanced technology features. The tool often comes equipped with a built-in LED light that illuminates the work area, making it easier to work in dimly lit conditions. This feature is particularly useful for tasks that require precision and attention to detail.

The versatility of the Craftsman 315.21211 is evidenced by its compatibility with various attachments and accessories. Whether you need to drill a hole, drive screws, or perform complex cutting tasks, this model adapts seamlessly to different functions. The quick-change chuck mechanism allows for easy swapping of bits, ensuring that users can transition between tasks quickly.

Safety is also a priority with the Craftsman 315.21211. The tool includes a safety lock feature that prevents accidental activation, providing peace of mind during operation. This thoughtful design element is essential for both seasoned users and those new to power tools.

In summary, the Craftsman 315.21211 stands out for its powerful motor, ergonomic design, advanced technology features, and versatility. These characteristics make it an invaluable tool for anyone looking to tackle a wide range of projects with confidence and ease. Whether you are a professional contractor or a weekend DIY warrior, the Craftsman 315.21211 promises to deliver reliability and exceptional performance in all your endeavors.
Top Page Image Contents