Craftsman 315.21211 owner manual General, Lubrication, Extension Cords

Page 27

_I, WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other

part may create a hazard or cause product damage.

GENERAL

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.

,_, WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating

oils, etc. come in contact with plastic parts. They contain chemicals that can damage, weaken or destroy plastic.

It has been found that electric tools are subject to accelerated wear and possible premature failure when they are used on fiberglass boats, sports cars, wallboard, spackling compounds, or plaster. The chips and grindings from these materials are highly abrasive to electric tool parts such as bearings, brushes, commutators, etc. Consequently, it is not recommended that this tool be used for extended work on any fiberglass material, wallboard, spackling compounds, or plaster. During any use on these materials it is extremely important that the tool is cleaned frequently by blowing with an air jet.

LUBRICATION

All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required.

EXTENSION CORDS

The use of any extension cord will cause some loss of power. To keep the loss to a minimum and to prevent

tool overheating, use an extension cord that is heavy enough to carry the current the tool will draw.

A wire gage size (A.W.G) of at least 14 is recom- mended for an extension cord 25 feet or less in

length. When working outdoors, use an extension

cord that is suitable for outdoor use. The cord'sjacket will be marked WA.

A CAUTION: Keep extension cords away from the cutting area and position the cord so that it will not get caught on lumber, tools, etc., during cutting operation.

WARNING: Check extension cords before each use. If damaged, replace immediately. Never use tool with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury.

A WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents OwnersManual Full ONE Year Warranty Do not USE in Dangerous Environ Symbolmeaning Safety Alert SymbolDouble Insulation Read ALL InstructionsAlways Wear Safety Glasses with Rules for Safe OperationDo not Remove the Sawsblade Always USE a Clamp to secure the work Rules for Safe OperationArbor Throw-BackThrough Sawing Blade Diameter Arbor No Load Speed Inch Compound Miter Saw Framingsquare BladewrenchMmHEXKEY DustguideKnow Your Compound Miter SAW AMP MotorCutting Capacities Spindle Lock Button Carrying HandleMiter Lock Handle LOCK-OFF LeverSELF-RETRACTING Lower Blade Guard Positive Stops on Miter TableBevel Lock Knob Electric BrakeTighten Control ARM Miter Toinstall Blade Miter Lock HandlePhillipsscrew Mitertable Lockhandle Dust Guide Tighten Literbladewasher Withdouble D Flats Bladebolt Lowerphillips BladeguardscrewBoltcover On Spindle Innerblade Washerwh BladeTo the Fence Squaring the Miter TableBracket Wrench Squaring the SAW Blade to the FenceMmSOCKET Headscrew Mounting MiterFence Combination Miter Square TABLE,ADJUSTMENTSAREREQUIREDSquaring the Blade to Miter TableCutting a Slot in the Zero Clearance Throat Plate Pivot AdjustmentsBevel Pivot Adjustment Depth Stop AdjustmentsTo Crosscut with Your Miter SAW Cutting with Your Compound Miter SAW CrosscuttingBevel CUT Leftside Rightside Indicator Point Scalescale MounngbracketTo Bevel CUT with Your Miter SAW Straight CrosscutCuts Compound Miter CUTCompound Mitercut To Make a Compound CUT with Your Miter SAWLongworkpiece Support Long WorkpiecesBefore turning on the saw, perform a dry run Sag, The support should let the werkpiece lay flat onCutting Compound Miters OfsideLaying Molding Flat on Cutting Crown MoldingWide Board Cutting Warped MaterialClamping Wide Workpieces WrongGeneral LubricationExtension Cords Brush CAP Brush ReplacementAssembly Fig BrushPage Rf- J =- ,- J ¢ Page Soooo,-o Ul el O00 ILl O 9 9 9 9 9 HomeCentralsM

315.21211 specifications

The Craftsman 315.21211 is a versatile power tool known for its robust design and exceptional performance. This model, primarily aimed at both professionals and DIY enthusiasts, boasts a range of features that make it an essential addition to any workshop or toolset.

One of the main features of the Craftsman 315.21211 is its powerful motor, designed to deliver consistent performance even under heavy loads. This motor allows for efficient cutting, drilling, and fastening, making it suitable for a variety of applications. The tool's high RPM rating enables it to handle tough materials like hardwood, metal, and plastic with ease, ensuring clean and precise results.

The ergonomic design of the Craftsman 315.21211 enhances user comfort during extended use. The rubberized grip reduces vibrations and improves control, thus minimizing fatigue. Additionally, the tool is relatively lightweight, which contributes to easier handling and maneuverability, especially in tight or awkward spaces.

Another significant aspect of the Craftsman 315.21211 is its inclusion of advanced technology features. The tool often comes equipped with a built-in LED light that illuminates the work area, making it easier to work in dimly lit conditions. This feature is particularly useful for tasks that require precision and attention to detail.

The versatility of the Craftsman 315.21211 is evidenced by its compatibility with various attachments and accessories. Whether you need to drill a hole, drive screws, or perform complex cutting tasks, this model adapts seamlessly to different functions. The quick-change chuck mechanism allows for easy swapping of bits, ensuring that users can transition between tasks quickly.

Safety is also a priority with the Craftsman 315.21211. The tool includes a safety lock feature that prevents accidental activation, providing peace of mind during operation. This thoughtful design element is essential for both seasoned users and those new to power tools.

In summary, the Craftsman 315.21211 stands out for its powerful motor, ergonomic design, advanced technology features, and versatility. These characteristics make it an invaluable tool for anyone looking to tackle a wide range of projects with confidence and ease. Whether you are a professional contractor or a weekend DIY warrior, the Craftsman 315.21211 promises to deliver reliability and exceptional performance in all your endeavors.
Top Page Image Contents