Craftsman 315.21211 owner manual Cutting with Your Compound Miter SAW Crosscutting

Page 19

DEPTH STOP

L_

ADJUSTMENT,

 

SCREW

 

BEVEL

LOCKKNOB

MITER

TABLE

POSITIVE LOCKNUT(S)

 

STOPADJUSTMENT

 

SCREWFOR0° ANGLES

Fig. 25

Lower the blade into the zero clearance throat plate of the miter table. Check blade clearance and maximum cutting distance (distance from fence where blade enters) to front of miter table slot.

•Readjust if necessary.

_1, WARNING: Do not start your compound miter saw without checking for interference between

the blade and the miter table support. Damage could result to the btade if it strikes the miter

table support during operation of the saw.

•Tighten the hex nut with a 17 mm wrench or adjustable wrench.

•To prevent the depth stop adjustment screw from turning while tightening the hex nut, carefully hold it with the hex key wrench while tightening the hex nut.

APPLICATIONS

(Use onty for the purposes isted below)

•Cross cutting wood and plastic.

•Cross cutting miters, joints, etc. for picture frames, moldings, door casings, and fine joinery.

Note: The 104 tooth crosscut blade provided is fine for most wood cutting operations, but for fine joinery cuts or cutting plastic, use one of the accessory blades available from your nearest Sears store.

_1= WARNING: Before starting any cutting operation, clamp or bolt your compound miter

saw to a workbench. Never operate your miter saw on the floor or in a crouched position. Failure to heed this warning can result in serious personal injury.

CUTTING WITH YOUR COMPOUND MITER SAW

A WARNING: When using a work clamp or C-clamp to secure your workpiece, clamp workpiece on one side of the blade only. The workpiece must remain free on one side of the blade to prevent the blade from binding in workpiece. The workpiece binding the blade will cause motor stalling and kickback. This situation could cause an accident resulting in possible serious personal injury.

CROSSCUTTING

See Figure 26.

A crosscut is made by cutting across the grain of the workpiece. A straight crosscut is made with the miter table set at the zero degree position. Miter crosscuts are made with the miter table set at some angle other than zero.

TO CROSSCUT WITH YOUR MITER SAW:

•Pull out the lock pin and lift saw arm to its full height.

•Loosen the miter lock handle. Rotate the miter

lock handle approximately one-half turn to the left to loosen.

•Press the miter lock plate down with your thumb and hold.

•Rotate the control arm until the pointer aligns with the desired angle on the miter scale.

•Release the miter lock plate.

Note: You can quickly locate 0°, 22-1/2 _ left or right, and 45° left or right by releasing the lock plate as you rotate the control arm. The lock plate will seat itself in one of the positive stop notches, located in the miter table frame.

•Tighten the miter lock handle securely.

A WARNING: To avoid serious personal injury, always tighten the miter lock handle securely before making a cut. Failure to do so could result in movement of the control arm or miter table while making a cut.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents OwnersManual Full ONE Year Warranty Do not USE in Dangerous Environ Symbolmeaning Safety Alert SymbolDouble Insulation Read ALL InstructionsRules for Safe Operation Always Wear Safety Glasses withDo not Remove the Sawsblade Always USE a Clamp to secure the work Rules for Safe OperationThrow-Back ArborThrough Sawing Blade Diameter Arbor No Load Speed Inch Compound Miter Saw Framingsquare BladewrenchMmHEXKEY DustguideAMP Motor Know Your Compound Miter SAWCutting Capacities Spindle Lock Button Carrying HandleMiter Lock Handle LOCK-OFF LeverSELF-RETRACTING Lower Blade Guard Positive Stops on Miter TableBevel Lock Knob Electric BrakeMiter Lock Handle Tighten Control ARM Miter Toinstall BladePhillipsscrew Mitertable Lockhandle Dust Guide Tighten Literbladewasher Withdouble D Flats Bladebolt Lowerphillips BladeguardscrewBoltcover On Spindle Innerblade Washerwh BladeTo the Fence Squaring the Miter TableBracket Wrench Squaring the SAW Blade to the FenceMmSOCKET Headscrew Mounting MiterFence Combination Miter Square TABLE,ADJUSTMENTSAREREQUIREDSquaring the Blade to Miter TableCutting a Slot in the Zero Clearance Throat Plate Pivot AdjustmentsBevel Pivot Adjustment Depth Stop AdjustmentsTo Crosscut with Your Miter SAW Cutting with Your Compound Miter SAW CrosscuttingBevel CUT Leftside Rightside Indicator Point Scalescale MounngbracketTo Bevel CUT with Your Miter SAW Straight CrosscutCuts Compound Miter CUTCompound Mitercut To Make a Compound CUT with Your Miter SAWLongworkpiece Support Long WorkpiecesBefore turning on the saw, perform a dry run Sag, The support should let the werkpiece lay flat onCutting Compound Miters OfsideLaying Molding Flat on Cutting Crown MoldingWide Board Cutting Warped MaterialClamping Wide Workpieces WrongLubrication GeneralExtension Cords Brush CAP Brush ReplacementAssembly Fig BrushPage Rf- J =- ,- J ¢ Page Soooo,-o Ul el O00 ILl O 9 9 9 9 9 HomeCentralsM

315.21211 specifications

The Craftsman 315.21211 is a versatile power tool known for its robust design and exceptional performance. This model, primarily aimed at both professionals and DIY enthusiasts, boasts a range of features that make it an essential addition to any workshop or toolset.

One of the main features of the Craftsman 315.21211 is its powerful motor, designed to deliver consistent performance even under heavy loads. This motor allows for efficient cutting, drilling, and fastening, making it suitable for a variety of applications. The tool's high RPM rating enables it to handle tough materials like hardwood, metal, and plastic with ease, ensuring clean and precise results.

The ergonomic design of the Craftsman 315.21211 enhances user comfort during extended use. The rubberized grip reduces vibrations and improves control, thus minimizing fatigue. Additionally, the tool is relatively lightweight, which contributes to easier handling and maneuverability, especially in tight or awkward spaces.

Another significant aspect of the Craftsman 315.21211 is its inclusion of advanced technology features. The tool often comes equipped with a built-in LED light that illuminates the work area, making it easier to work in dimly lit conditions. This feature is particularly useful for tasks that require precision and attention to detail.

The versatility of the Craftsman 315.21211 is evidenced by its compatibility with various attachments and accessories. Whether you need to drill a hole, drive screws, or perform complex cutting tasks, this model adapts seamlessly to different functions. The quick-change chuck mechanism allows for easy swapping of bits, ensuring that users can transition between tasks quickly.

Safety is also a priority with the Craftsman 315.21211. The tool includes a safety lock feature that prevents accidental activation, providing peace of mind during operation. This thoughtful design element is essential for both seasoned users and those new to power tools.

In summary, the Craftsman 315.21211 stands out for its powerful motor, ergonomic design, advanced technology features, and versatility. These characteristics make it an invaluable tool for anyone looking to tackle a wide range of projects with confidence and ease. Whether you are a professional contractor or a weekend DIY warrior, the Craftsman 315.21211 promises to deliver reliability and exceptional performance in all your endeavors.
Top Page Image Contents