Craftsman 315.21211 Lowerphillips Bladeguardscrew, Boltcover On Spindle Innerblade Washerwh

Page 14

LOWERPHILLIPS

BLADEGUARDSCREW

•Wipe a drop of oil onto inner blade washer and outer blade washer where they contact the blade.

,_ WARNING: If inner blade washer has been removed, replace it before placing blade on

spindle. Failure to do so could cause an accident

since blade wil_not tighten properly,

BOLTCOVER

ON SPINDLE

 

INNERBLADE

 

WASHERW_H

 

DOUBLE"D" FLATS

TO

 

 

BLADE

TIGHTEN

:)LITERBLADEWASHER

 

WITHDOUBLE"D" FLATS

BLADEBOLT

Fig. 11

•Depress the spindle lock button and rotate the blade bolt until the spindle locks. See Figure 12.

•Using the blade wrench provided, loosen and remove the blade bolt.

Note: The blade bolt has left hand threads. Turn blade bolt clOCkwiseto loosen.

•Remove outer blade washer. Do not remove inner blade washer.

•Fit saw blade inside lower blade guard and onto spindle. The blade teeth point downward at the front of saw as shown in figure 11.

CAUTION: Always instaIJ the blade with the blade teeth and the arrow printed on the side of the blade pointing down at the front of the saw, The direction of blade rotation is also stamped with an arrow on the upper blade guard.

•Replace outer blade washer, The double "D"flats on the blade washers align with the flats on the spindle.

•Depress spindle lock button and replace blade bolt.

Note: The blade bolt has left hand threads. Turn blade bolt counterclockwise to tighten.

•Tighten blade bolt securely.

•Remove the blade wrench and store it in a safe place for future use.

•Replace the lower blade guard and blade bolt cover.

•Retighten phillips screw securing blade bolt cover. Tighten screw securely. See Figure 11.

SPINDLE

BUTTON

_. WARNING: Make sure the spindle lock button is not engaged before reconnecting saw into power

source, Never engage spindle lock button when blade is rotating.

Your compound miter saw has been adjusted at the factory for making very accurate cuts. However, some of the components might have been jarred out of alignment during shipping. Also, over a period of time, readjustmentwill probably become necessary due to wear. After unpacking your saw, check the following adjustments before you begin using saw. Make any readjustments that are necessary and periodically check the parts alignment to make sure that your saw is cutting accurately.

_.

WARNING: Your saw should never be

Fig. 12

connected to power supply when you are

 

assembling parts, making adjustments, installing

 

or removing blades, or when not in use.

 

Disconnectingyour saw will prevent accidental

 

starting that could cause serious injury.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents OwnersManual Full ONE Year Warranty Read ALL Instructions Symbolmeaning Safety Alert SymbolDouble Insulation Do not USE in Dangerous EnvironDo not Remove the Sawsblade Always Wear Safety Glasses withRules for Safe Operation Rules for Safe Operation Always USE a Clamp to secure the workThrough Sawing ArborThrow-Back Blade Diameter Arbor No Load Speed Inch Compound Miter Saw Dustguide BladewrenchMmHEXKEY FramingsquareCutting Capacities Know Your Compound Miter SAWAMP Motor LOCK-OFF Lever Carrying HandleMiter Lock Handle Spindle Lock ButtonElectric Brake Positive Stops on Miter TableBevel Lock Knob SELF-RETRACTING Lower Blade GuardPhillipsscrew Mitertable Lockhandle Dust Guide Tighten Control ARM Miter Toinstall BladeMiter Lock Handle Blade Lowerphillips BladeguardscrewBoltcover On Spindle Innerblade Washerwh Tighten Literbladewasher Withdouble D Flats BladeboltSquaring the Miter Table To the FenceHeadscrew Mounting Miter Squaring the SAW Blade to the FenceMmSOCKET Bracket WrenchMiter Table TABLE,ADJUSTMENTSAREREQUIREDSquaring the Blade to Fence Combination Miter SquareDepth Stop Adjustments Pivot AdjustmentsBevel Pivot Adjustment Cutting a Slot in the Zero Clearance Throat PlateCutting with Your Compound Miter SAW Crosscutting To Crosscut with Your Miter SAWStraight Crosscut Leftside Rightside Indicator Point Scalescale MounngbracketTo Bevel CUT with Your Miter SAW Bevel CUTCompound Miter CUT CutsTo Make a Compound CUT with Your Miter SAW Compound MitercutSag, The support should let the werkpiece lay flat on Support Long WorkpiecesBefore turning on the saw, perform a dry run LongworkpieceOfside Cutting Compound MitersCutting Crown Molding Laying Molding Flat onWrong Cutting Warped MaterialClamping Wide Workpieces Wide BoardExtension Cords GeneralLubrication Brush Brush ReplacementAssembly Fig Brush CAPPage Rf- J =- ,- J ¢ Page Soooo,-o Ul el O00 ILl O 9 9 9 9 9 HomeCentralsM

315.21211 specifications

The Craftsman 315.21211 is a versatile power tool known for its robust design and exceptional performance. This model, primarily aimed at both professionals and DIY enthusiasts, boasts a range of features that make it an essential addition to any workshop or toolset.

One of the main features of the Craftsman 315.21211 is its powerful motor, designed to deliver consistent performance even under heavy loads. This motor allows for efficient cutting, drilling, and fastening, making it suitable for a variety of applications. The tool's high RPM rating enables it to handle tough materials like hardwood, metal, and plastic with ease, ensuring clean and precise results.

The ergonomic design of the Craftsman 315.21211 enhances user comfort during extended use. The rubberized grip reduces vibrations and improves control, thus minimizing fatigue. Additionally, the tool is relatively lightweight, which contributes to easier handling and maneuverability, especially in tight or awkward spaces.

Another significant aspect of the Craftsman 315.21211 is its inclusion of advanced technology features. The tool often comes equipped with a built-in LED light that illuminates the work area, making it easier to work in dimly lit conditions. This feature is particularly useful for tasks that require precision and attention to detail.

The versatility of the Craftsman 315.21211 is evidenced by its compatibility with various attachments and accessories. Whether you need to drill a hole, drive screws, or perform complex cutting tasks, this model adapts seamlessly to different functions. The quick-change chuck mechanism allows for easy swapping of bits, ensuring that users can transition between tasks quickly.

Safety is also a priority with the Craftsman 315.21211. The tool includes a safety lock feature that prevents accidental activation, providing peace of mind during operation. This thoughtful design element is essential for both seasoned users and those new to power tools.

In summary, the Craftsman 315.21211 stands out for its powerful motor, ergonomic design, advanced technology features, and versatility. These characteristics make it an invaluable tool for anyone looking to tackle a wide range of projects with confidence and ease. Whether you are a professional contractor or a weekend DIY warrior, the Craftsman 315.21211 promises to deliver reliability and exceptional performance in all your endeavors.
Top Page Image Contents