Craftsman 315.21211 owner manual To Bevel CUT with Your Miter SAW, Straight Crosscut

Page 20

STRAIGHT

CROSSCUT

{_

C-CLAMP

Fig. 26

•Place the workpiece fiat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of a beard is placed against the fence, the beard could collapse on the blade at the end of the cut, jamming the blade. See Figures 33 and 34.

•When cutting long pieces of lumber or molding, support the opposite end of the stock with a roller stand or with a work surface level with the saw table. See Figure 31.

•Align cutting line on the workpiece with the edge of saw blade.

Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clampto secure the workpiece when possible. See Figure 26.

,_ WARNING: To avoid serious personal injury, keep your hands outside the no hands zone; at

least 3 in. from blade. Never perform any cutting operation freehand (without holding workpiece against the fence). The blade could grab the workpiece if it slips or twists.

•Before turning on the saw, perform a dry run of the cutting operation just to make sure that no problems willoccur when the cut is made.

•Grasp the saw handle firmly, press the lock-off tab

down, then squeeze the switch trigger. Allow several seconds for the blade to reach maximum speed.

•Slowly lower the blade into and through the workpiece. See Figure 26.

•Release the switch triggerand allow the saw blade to stop rotating before raising the blade out of workpiece. Wait until the electric brake stops

from the miter table.

BEVEL CUT

blade from turning before removing the workpiece See Figures27 and 28.

A bevel cut is made by cutting across the grain of the

workpiece with the blade angled to the workpiece. A straight bevel cut is made with the miter table set at

the zero degree position and the blade set at an angle between 0° and 45°.

LEFTSIDE

RIGHTSIDE

LEFT

RIGHT

INDICATOR

INDICATOR

POINT

POINT

SCALESCALE

MOUN_NGBRACKET

Fig. 27

TO BEVEL CUT WITH YOUR MITER SAW:

•Pull out the lock pin and lift saw arm to its full height.

•Loosen the miter lock handle. Rotate the miter

lock handle approximately one-half turn to the left to loosen.

Press the miter lock plate down with your thumb and hold.

Rotate the control arm until the pointer aligns with zero on the miter scale.

Release the miter lock plate.

Note: You can quickly locate zero by releasing the lock plate as you rotate the control arm. The lock plate will seat itself in one of the built-in positive stop notches, located in the miter table frame.

•Tighten the miter lock handle securely.

WARNING: To avoid serious personal injury, always tighten the miter lock handle securely before making a cut. Failure to do so could result in movement of the control arm or miter table while making a cut.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents OwnersManual Full ONE Year Warranty Symbolmeaning Safety Alert Symbol Double InsulationRead ALL Instructions Do not USE in Dangerous EnvironDo not Remove the Sawsblade Always Wear Safety Glasses withRules for Safe Operation Rules for Safe Operation Always USE a Clamp to secure the workThrough Sawing ArborThrow-Back Blade Diameter Arbor No Load Speed Inch Compound Miter Saw Bladewrench MmHEXKEYDustguide FramingsquareCutting Capacities Know Your Compound Miter SAWAMP Motor Carrying Handle Miter Lock HandleLOCK-OFF Lever Spindle Lock ButtonPositive Stops on Miter Table Bevel Lock KnobElectric Brake SELF-RETRACTING Lower Blade GuardPhillipsscrew Mitertable Lockhandle Dust Guide Tighten Control ARM Miter Toinstall BladeMiter Lock Handle Lowerphillips Bladeguardscrew Boltcover On Spindle Innerblade WasherwhBlade Tighten Literbladewasher Withdouble D Flats BladeboltSquaring the Miter Table To the FenceSquaring the SAW Blade to the Fence MmSOCKETHeadscrew Mounting Miter Bracket WrenchTABLE,ADJUSTMENTSAREREQUIRED Squaring the Blade toMiter Table Fence Combination Miter SquarePivot Adjustments Bevel Pivot AdjustmentDepth Stop Adjustments Cutting a Slot in the Zero Clearance Throat PlateCutting with Your Compound Miter SAW Crosscutting To Crosscut with Your Miter SAWLeftside Rightside Indicator Point Scalescale Mounngbracket To Bevel CUT with Your Miter SAWStraight Crosscut Bevel CUTCompound Miter CUT CutsTo Make a Compound CUT with Your Miter SAW Compound MitercutSupport Long Workpieces Before turning on the saw, perform a dry runSag, The support should let the werkpiece lay flat on LongworkpieceOfside Cutting Compound MitersCutting Crown Molding Laying Molding Flat onCutting Warped Material Clamping Wide WorkpiecesWrong Wide BoardExtension Cords GeneralLubrication Brush Replacement Assembly FigBrush Brush CAPPage Rf- J =- ,- J ¢ Page Soooo,-o Ul el O00 ILl O 9 9 9 9 9 HomeCentralsM

315.21211 specifications

The Craftsman 315.21211 is a versatile power tool known for its robust design and exceptional performance. This model, primarily aimed at both professionals and DIY enthusiasts, boasts a range of features that make it an essential addition to any workshop or toolset.

One of the main features of the Craftsman 315.21211 is its powerful motor, designed to deliver consistent performance even under heavy loads. This motor allows for efficient cutting, drilling, and fastening, making it suitable for a variety of applications. The tool's high RPM rating enables it to handle tough materials like hardwood, metal, and plastic with ease, ensuring clean and precise results.

The ergonomic design of the Craftsman 315.21211 enhances user comfort during extended use. The rubberized grip reduces vibrations and improves control, thus minimizing fatigue. Additionally, the tool is relatively lightweight, which contributes to easier handling and maneuverability, especially in tight or awkward spaces.

Another significant aspect of the Craftsman 315.21211 is its inclusion of advanced technology features. The tool often comes equipped with a built-in LED light that illuminates the work area, making it easier to work in dimly lit conditions. This feature is particularly useful for tasks that require precision and attention to detail.

The versatility of the Craftsman 315.21211 is evidenced by its compatibility with various attachments and accessories. Whether you need to drill a hole, drive screws, or perform complex cutting tasks, this model adapts seamlessly to different functions. The quick-change chuck mechanism allows for easy swapping of bits, ensuring that users can transition between tasks quickly.

Safety is also a priority with the Craftsman 315.21211. The tool includes a safety lock feature that prevents accidental activation, providing peace of mind during operation. This thoughtful design element is essential for both seasoned users and those new to power tools.

In summary, the Craftsman 315.21211 stands out for its powerful motor, ergonomic design, advanced technology features, and versatility. These characteristics make it an invaluable tool for anyone looking to tackle a wide range of projects with confidence and ease. Whether you are a professional contractor or a weekend DIY warrior, the Craftsman 315.21211 promises to deliver reliability and exceptional performance in all your endeavors.
Top Page Image Contents