Craftsman 286.26829 KICKBACK..,WHAT Causes IT and Ways to Prevent IT, Causes of Kickback

Page 4

SAFETY RULES FOR SAW cont.

1t, When _emoving the blades from the tool, ALWAYS wear protective gloves when grasping the blades or accessory. Accessories may be hot after prolonged use.

KICKBACK..,WHAT CAUSES IT AND WAYS TO PREVENT IT

The Causes of Kickback

t.Kickback is a sudden reaction to a pinched, bound or misaligeed saw blades, which cause the uncont_o!led saw to lift up and out of the workpiece and towards lhe operator.

2.When tile blades are pinched or bound tightly by the kerf closing down, the blades stall and the motor reaction drives the unit rapidly back towards the operator.

3.If the blades become twisted or misaIigned in the cut, the teeth at the back edges of the blades can dig into the top surface of the wood. This causes the blades to climb out of the kerf and jump back towards the operator.

4.Kickback is a result of tool misuse and/or incorrect operating procedures or conditions. It can be avoided by taking the proper precautions, as listed below.

Ways to Prevent Kickback

f. ALWAYS maintain a firm grip with both hands on the saw and position your body and arms to allow you to resist KICKBACK forces, KICKBACK forces can

be controlled by the operator, if the proper precautions are taken.

2.If the blades are binding, or when you are interrupting a cut for any reason,

ALWAYS turn off the saw and hold the saw motionless in the material until the blades come to a complete stop. NEVER attempt to remove the saw from the work or pull the saw backward while the blades are in motion or

KICKBACK may occur. ALWAYS check and be ready to take corrective action to eliminate tile cause of blade binding.

3.When restarting the saw in the workpiece, ALWAYS center the blades in the

kerr end check to be sure that the saw teeth are not engaged into the material. If the saw blades are binding, they may walk up or KICKBACK from the workpiece when the saw is restarted.

4.ALWAYS support large panels to minimize the risk of blades pinching and KICKBACK. Large panels tend to sag under their own weight. Supports MUST be placed under tile paoeI on both sides, near the line of cut and near the edge of the panel.

5.#O NOT use a dull or damaged blades. Unsharpened or improperly set blades

produce narrow kerf which causes excessive friction, blade binding and

KICKBACK.

6.ALWAYS use extra caution when making a "Pocket Cut" into existing walls or

other blind areas. The protruding blades may cut objects that can cause

KICKBACK.

7.ALWAYS have the saw blades at full speed before contacting workpiece

8.ALWAYS keep your body positioned to either side of the saw blades, but not in line with ti_e saw blades. KICKBACK could cause the saw to jump backwards towards the operator. KICKBACK forces can be controlled by the operator, if proper precautions are taken

ALWAYS hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord.

Contact with a "live" wire will make the exposed metal parts of the tool "live" and

sbock the operator.

6

ADDITIONAL RULES FOR SAFE OPERATION

follow all instructions listed below may result in electric shock, fire and/or serious I

I Z_ WARNING: BE SURE to read and understand all instructions. Failure to personal injury.

1.Know your power tool. Read operator's manual carefully. Learn the applications and limitations, as well as the specific potential hazards related to this tool. Following this rule wil! reduce the risk of electric shock, fire or serious injury.

2.ALWAYS wear safety glasses or eye shields when using this saw. Everyday eyeglasses have only impact-resistant lenses; they are NOT safety glasses. Following this rule will reduce the risk of serious personal injury.

3.ALWAYS protect your lungs. Wear a face mask or dust mask if the operation is dusty. Following this rule will reduce the risk of serious personaI injury

4.ALWAYS protect your hearing.Wear hearing protection during extended periods of operation. Following this rule will reduce the risk of serious personal injury.

5.ALWAYS inspect the tool cords periodically and if damaged have them repaired at your nearest Sears Service Center or other Authorized Service Facility. ALWAYS be aware of the cord location. Following this rule will reduce the risk of electric shock or fire.

6.ALWAYS check for damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine if it will operate properly and perform its intended function. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool's operation. A guard or other part that is damaged, should be properly repaired or replaced at a Sears Service Center. Following this rule will v_duce the risk of electric shock, fire or serious injury.

7.DO NOT abuse the cord. NEVER use the cord to carry the tool or pull the plug from the outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock. Following this rule wil! reduce the risk of electric shock or fire.

8.ALWAYS make sure that your extension cord is in good condition. When using an extension cord be sure to use one that is heavy enough to carry the current that your tool will draw. A wire gauge size (A.W.G.) of at least 16 is recommended for an extension 100 feet or less in length. Using an extension cord that is over 100 feet inlength is not recommended. If in doubt, use the next heavier gauge. Smaller gauge wires, have greater capacity (16 gauge wire has more capacity than 18 gauge wire). An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating.

9.DO NOT use the tool while tired or under the influence of drugs, alcohol or

any medication. Following this rule will reduce the risk ofelectdc shock, fire or serious personal injury.

t0.SAVETHESE INSTRUCTIONS. Refer to them frequently and use them to instruct others who may use this tool. If someone borrows this tool, make

sure they have these instructions also.

Image 4
Contents Maintenance ESPAIIOL, PAGE25 SafetyIP R 0 F E S S I 0 N a L J ONE Full Year Warranty on Craftsman Work Area SafetyElectrical Safety Professional Twin Cutter SAWPersonalsafety Tool USE and Care SafetyService Safety Safety Rules for SawsKICKBACK..,WHAT Causes IT and Ways to Prevent IT Causes of KickbackKickback Additional Rules for Safe OperationLabel on your tool may include the following symbols IMPORTANT! Read ALL InstructionsKnowyour SAW see Fig UnpackingSawblades Blade Guard System\ Fig KickbackBlades perpendicular to workpiece Approximately StartingcutTo Help Maintain Control Cutting Instructions Feed SpeedCutting Instructions Cutting ALL MaterialsLubricatnginstructions See Figure CCutting Shaped Platea Up to t/8-in,thick See Fig. tOGeneral LubricationDouble Insulation Extension CordsTWIN-CUTTER SAW Model Number Item No Parts no Part Description Qty Parts No CityMantenimiento SeguridadIPR 0 FES S I 0 HAL Seguridad EN EL Lugar Detrabajo Repuestosy Reparacion Sears MAS Cercano EN LOSSeguridad Electrica Seguridad Personal Reglas DE Seguridad Para LAS Sierras Causes del RetroceeoAdvertencia Reglas Adicionales Para Funcionamiento SeguroCoo todas Conozca SU Sierra ver FigHojasdelasierra Sistema DE Proteccion DE LAS HojasRetroceso PeligroComienzo DE UN Corte ImportantePara Ayudar a Mantener EL Control Las hojas en movimiento puede sufrir una lesion graveInstruccionespara LOS Cortes Instrucciones Para LOS CortesCorte DE Todo Tipo DE Materiales Velocidad DE AvanceInstrucciones DE Lubricacion AdvertenciaTorte de placas con forma No rectangulares PulgGeneramdades Instalacion DE LAS Hojas DE Repuesto EN LA Sierra Ver FigsLubricacion Aislamientodoble Cordones DE ExtensionDescripcibn Cantidad No.de pleza Description PW036PW038 PW043MY-HOME Anytime,day or night SU-HOGAR 18784Po42T

286.26829 specifications

The Craftsman 286.26829 is a standout product that perfectly exemplifies the brand's reputation for delivering high-quality tools that cater to the needs of both DIY enthusiasts and professionals. This durable air compressor boasts a variety of impressive features and technologies that enhance its functionality and usability.

One of the key features of the Craftsman 286.26829 is its robust 150 PSI maximum pressure capability. This high-pressure output allows it to support a wide range of pneumatic tools, including nailers, staplers, and air blow guns. Whether you are inflating tires or powering pneumatic equipment, this air compressor provides the power needed for efficient operation.

Designed with user convenience in mind, the Craftsman 286.26829 is equipped with a 6-gallon tank. This portable size is perfect for both home and on-the-go tasks, making it easy to transport from one job site to another. The tank's capacity strikes an excellent balance between power and portability, allowing users to work longer without constant refilling.

Another notable feature is the oil-free pump design, which reduces maintenance requirements and enhances the unit's longevity. This characteristic not only ensures hassle-free operation but also makes it an environmentally friendly choice, as it eliminates the need for oil changes. Users can enjoy a cleaner work environment without worrying about spills or maintenance costs.

The Craftsman 286.26829 is also designed for ease of use, featuring easy-to-read gauges that provide clear visibility on tank pressure and output. The quick-connect couplers facilitate a seamless connection to air tools, enhancing efficiency and reducing downtime.

In terms of safety, the air compressor includes integrated safety features such as thermal overload protection, which prevents overheating by automatically shutting off the unit if it becomes too hot. This aspect further extends its durability and ensures safe operation for users.

In conclusion, the Craftsman 286.26829 is a versatile air compressor that combines power, portability, and user-friendly features, making it an excellent choice for various applications. With its durable construction, high PSI output, and low maintenance requirements, it is a reliable tool that meets the demands of both home projects and professional jobs. Whether you're a seasoned professional or a novice DIYer, this air compressor is designed to make your tasks more manageable and efficient.