Craftsman 286.26829 owner manual Sawblades, Blade Guard System, Fig, Kickback

Page 6

SAWBLADES

Even the best saw blades will not cut efficiently if they are not kept clean, sharp and properly set. Using dull blades will place a heavy load on your saw and increase the danger of kickback. Keep extra blades on hand, so sharp blades are always available. Gum and wood pitch hardened on your blades will slow your saw down. Use gum and pitch remover, hot water or kerosene to remove these accumulations.

DO NOT use gasoline.

z_ WARNING: This Twin Cutter saw uses specially designed 61/sqn. blades I and no other types or sizes of blades should ever be used_ Other types and sizes of blades will not operate safely in this saw and cou d result in serious persona n ury.

To order extra blades or to replace the blades that came with the saw, see page 21 of this manual for ordering instructions. To install new blades onto to your saw see

the special instructions on pages 17 to 19 of this manual for proper removal and installation of blades.

BLADE GUARD SYSTEM

The lower blade guard, attached to your saw, is there for your protection and safety. It should NEVER be altered for any reason. If it becomes damaged or begins to return slowly or sluggishly. DO NOT operate your saw until the problem has been corrected or the damaged part has been replaced. ALWAYS leave the guard in its correct operating position when using the saw.

Z_ DANGER:

When sawing through a

\ Fig. 2

workpiece, the lower blade guard does aot

 

cover the blade on the underside of the

 

workpiece. Since the blade is exposed on the

 

underside of the workpiece, ALWAYS keep

 

your hands and fingers away from the cutting

 

area (see Fig. 2). Any part of your body

 

coming in contact with the moving blade will

 

result in serious

injury.

 

I ower Blade Guard is in UP position when making a cut. Blades are exposed on underside of workpiece

Z_ WARNING: NEVER use the saw when the guard is not operating properly. The guard should be checked for correct operation before each use. If you drop your saw, check the lower blade guard for damage before using.

NOTE: The guard is operating properly when it moves freely and then readily returns to the closed position. If, for any reason, your lower blade guard does not close freely, take it to your nearest Sears Repair Center for service before using it.

KICKBACK

Kickback occurs when the blades stall rapidly and the saw is driven back towards you. Blade stalling is caused by any action which pinches the blade in the material being cut.

IMPORTANT: The best guard against kickback is to avoid dangerous practices.

z_ DANGER: ALWAYS turn OFF power to saw immediately if the blades bind or the saw stalls. Kickback could cause you to lose control of the saw. Loss of

control can ead to serious njury.

ALWAYS provide proper support for the workpiece and hold the saw with both hands

Kickback is Caused By:

1.Twisting the blades while making a cut.

2.Making a cut with a dull, gummed up, or improperly set blades.

3.Not providing proper support for workpiece. ALWAYS provide proper support as shown in Fig. 3.

4.Forcing a cut.

5.Cutting warped or wet lumber.

6 Tool misuse or incorrect operating procedures.

7.Contacting the werkpiece with blades at less than full speed.

To Lessen the Chance of Kickback

1.ALWAYS approach the workpiece with the saw at an angle of approximately 30 ° to the workpiece. (see Fig, 4,)

2.ALWAYS make straight cuts,

This will help prevent twisting the blade in the cut.

3.ALWAYS use clean, sharp and

properly set blades. NEVER make cuts with dull blades.

4.ALWAYS properly support the

workpiece before beginning a cut. This will help you avoid pinching the blades (see Fig. 3),

5.ALWAYS use steady, even pressure when making a cut. NEVER force the cut.

6.DO NOT cat wet or warped lumber.

7.ALWAYS hold the saw firmly with both hands and keep your body in a balanced position. ALWAYS keep your body positioned to either side of the saw blades, but

not in line with the saw blades.This will help you resist the forces of kickback, should it occur.

IMPORTANT: When using your saw, ALWAYS stay alert and exercise control,

DO NOT remove your saw from the workpiece, while the blade is moving,

J

I

10

11

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Safety Maintenance ESPAIIOL, PAGE25IP R 0 F E S S I 0 N a L J Electrical Safety ONE Full Year Warranty on CraftsmanWork Area Safety Professional Twin Cutter SAWService Safety PersonalsafetyTool USE and Care Safety Safety Rules for SawsKickback KICKBACK..,WHAT Causes IT and Ways to Prevent ITCauses of Kickback Additional Rules for Safe OperationKnowyour SAW see Fig Label on your tool may include the following symbolsIMPORTANT! Read ALL Instructions Unpacking\ Fig SawbladesBlade Guard System KickbackStartingcut Blades perpendicular to workpiece ApproximatelyTo Help Maintain Control Cutting Instructions Cutting InstructionsFeed Speed Cutting ALL MaterialsCutting Shaped Platea LubricatnginstructionsSee Figure C Up to t/8-in,thick See Fig. tOGeneral LubricationDouble Insulation Extension CordsTWIN-CUTTER SAW Model Number Item No Parts no Part Description Qty Parts No CitySeguridad MantenimientoIPR 0 FES S I 0 HAL Repuestosy Reparacion Sears MAS Cercano EN LOS Seguridad EN EL Lugar DetrabajoSeguridad Electrica Seguridad Personal Reglas DE Seguridad Para LAS Sierras Causes del RetroceeoCoo todas AdvertenciaReglas Adicionales Para Funcionamiento Seguro Conozca SU Sierra ver FigRetroceso HojasdelasierraSistema DE Proteccion DE LAS Hojas PeligroPara Ayudar a Mantener EL Control Comienzo DE UN CorteImportante Las hojas en movimiento puede sufrir una lesion graveCorte DE Todo Tipo DE Materiales Instruccionespara LOS CortesInstrucciones Para LOS Cortes Velocidad DE AvanceTorte de placas con forma No rectangulares Instrucciones DE LubricacionAdvertencia PulgInstalacion DE LAS Hojas DE Repuesto EN LA Sierra Ver Figs GeneramdadesLubricacion Aislamientodoble Cordones DE ExtensionPW038 Descripcibn Cantidad No.de pleza DescriptionPW036 PW043MY-HOME Anytime,day or night SU-HOGAR 18784Po42T

286.26829 specifications

The Craftsman 286.26829 is a standout product that perfectly exemplifies the brand's reputation for delivering high-quality tools that cater to the needs of both DIY enthusiasts and professionals. This durable air compressor boasts a variety of impressive features and technologies that enhance its functionality and usability.

One of the key features of the Craftsman 286.26829 is its robust 150 PSI maximum pressure capability. This high-pressure output allows it to support a wide range of pneumatic tools, including nailers, staplers, and air blow guns. Whether you are inflating tires or powering pneumatic equipment, this air compressor provides the power needed for efficient operation.

Designed with user convenience in mind, the Craftsman 286.26829 is equipped with a 6-gallon tank. This portable size is perfect for both home and on-the-go tasks, making it easy to transport from one job site to another. The tank's capacity strikes an excellent balance between power and portability, allowing users to work longer without constant refilling.

Another notable feature is the oil-free pump design, which reduces maintenance requirements and enhances the unit's longevity. This characteristic not only ensures hassle-free operation but also makes it an environmentally friendly choice, as it eliminates the need for oil changes. Users can enjoy a cleaner work environment without worrying about spills or maintenance costs.

The Craftsman 286.26829 is also designed for ease of use, featuring easy-to-read gauges that provide clear visibility on tank pressure and output. The quick-connect couplers facilitate a seamless connection to air tools, enhancing efficiency and reducing downtime.

In terms of safety, the air compressor includes integrated safety features such as thermal overload protection, which prevents overheating by automatically shutting off the unit if it becomes too hot. This aspect further extends its durability and ensures safe operation for users.

In conclusion, the Craftsman 286.26829 is a versatile air compressor that combines power, portability, and user-friendly features, making it an excellent choice for various applications. With its durable construction, high PSI output, and low maintenance requirements, it is a reliable tool that meets the demands of both home projects and professional jobs. Whether you're a seasoned professional or a novice DIYer, this air compressor is designed to make your tasks more manageable and efficient.
Top Page Image Contents