Craftsman 315.22038 Cause Solution, Fence in Adjustments section, See Adjusting the Column

Page 59

PROBLEM

Saw blade tends to push wood to one side when cross cutting.

CAUSE

SOLUTION

1.

Blade is heeling.

1.

See Squaring the Blade to the

 

 

 

Fence in Adjustments section.

2.

Column tube is loose in column

2.

See Adjusting the Column

 

support.

 

Tube in Assembly section.

3.

Arm is loose or misaligned.

3.

See Setting the Arm Lock

 

 

 

Wheel in the Assembly section.

4.

Fence/tables are not straight.

4.

Check with square; sand or

 

 

 

replace.

5.

Blade or teeth are bent or dull.

5.

Sharpen or replace the blade.

 

 

 

See the removal procedure in

Assembly section.

59-(RRFT$14RN"RADIALSAW315.220380

Image 59
Contents OwnersManual Full ONE Year Warranty on Craftsman Radial ARM SAW CliaFTtHIIIr RADIALSAW315.220380 Read ALL Instructions Safety Alert SymbolAvoid Awkward Operations and Hand Never USE this Tool in AN ExplosiveBe Sure the Blade Clears the Work Page PIN Coverof Grounded Outletbox Extension CordsElectrical Connection Grounding InstructionsSee Figures Assembly sectionChanging Voltage CRRFTSMRWRADIALSAW315.22038010 Resin Sticky,sap-basedsubstance SAW Assemblyshownas Packed Cdef CtorDEOo0 Framingsquare 15RIIFTIMRNRADIALSAW315.220380 RRFTMRNRADIALSAW315.22038016 FtsmanreplacementpartsSerno 17CRAFTSMANRADIALSAW315.220380 AdvertenciaYoke Control Know Your Radial SAWSee a MethodSee Figures 9A-9D FeatureslistFigures 9A and 9B Dustguide Holddown Downknob Upper Bladeguard Lower MOTOR13/6.5AMP- Powersthe blade and isSee Figures 10,4 10C HexnutElevating Shaft Handwheel Screw Starwasher Mounting SAW to LEG StandCAP Screws Installing the Yoke AssemblyArmviewedfrombelow Clockwasher Armlockknob Carriagearm LockknobLeveling The Table Supports section Removing the BladeAttaching Table Supports See FigureRAFTSMANRADIALSAW315.22038026 Setting the ARM Lock KnobYokelock Handle Bevellockleverin Correctlockedposition Setting the Bevel Lock LeverStarwasher Socketscrew Bevel Locklever Tube Column Support Tightening the ARM and ColumnCAP Screws 29RRFTSMIWRADIALSAW315,220380 Elevation AdjustmentRotation Adjustment Column Silverblack Screws ColumnsupportEccentricscrew Wrench Graspand Hold Carriagebearing Adjusting the Carriage BearingsSee Figures 21A and 21B CarriagebearingBlade Wrenchat Front Armlock Knob Bevel Indexknob Leveling the Table SupportsHexnut Installing the Front TableSetscrew If there are any high or low areas on the front table Leveling the Front TableScrewand NUT Rivingknifebladenut Blade Tighten AssembledWasher Hole Support CUP To Washer Loosen Thumbscrew BladeguardAlign Riving Knife to Blade Spring Carriage Screws Lockknob Installing RIP Scale Indicators ScrewsRIP Scale Indicator Carriage Speednut Elevating Handwheel Straight Edge Framing Square Thereshouldbeno GapherewhenARM Lockknob Indexcap Bladesquaretotable Noadjustmentneeded Framing SquareAligning Blade to Table AT Obevel See Figures 3OA 30DArmlockknob SAW Viewed From Above Blade Square Adjustment BladeSquaring Blade to Fence See Figures 31A 31CSee Figures 32A-32C Adjustment GAPParalleling Blade to Table Carriagelockknob Aligning the RIP Scale IndicatorsIN-RIPSCALEON Rightsideof ARM RIP-SCALEINDICATOR OUT-RIPSCALEONLEFTSIDE of ARM RIP-SCALEINDICATORBarrel Carriage Assembly Installing Control CUT DeviceRIP Cuts Basic Operation of the Radial ARM SAWTypes of Cuts CrosscutsAvoiding Kickback Switch and Switch KEYInsertswitchkey Switchon Switchoff Causes of KickbackFeatherboards Cutting AidsPushsticks PushblocksCrosscut Rivingknife Elevating Handwheel Switch BevelMaking a Cross CUT Carriage Lockknob TableclampsErcut Elevating Handwheel Making a Miter CUTMaking a Bevel CUT Switch Handleyokelock Riving Elevating HandwheelBeveledand Elevating Handwheel Making a Compound Cross CUTInfeedfor RIP CUT Hazards and PrecautionsSetting UP a RIP CUT Switch ElevatingOUT RIP Cutting Blade Switch ANTI-KICKBACK PawlsMaking a RIP CUT Supportlongworkpieces IRAFTNIINRADIALSAW315.22038052 Making Oher CutsSee Cutting Long WorkpiecesNON-THROUGHCUT NON-THROUGH CutsMOTOR/ELECTRICAL General MaintenanceSolution Problem CauseProblem Cause Solution 57CRRFTSMANRADIALSAW315.220380 Problem CausesolutionSee Adjusting the Column Tube in Assembly section Arm Lock ProblemSee Squaring the Blade to Tube in Assembly section Cause SolutionFence in Adjustments section See Adjusting the ColumnCraftsman Radial ARM SAW Model no SeergureiKEY Part Craftsman Radial ARM SAW- Model noKEY Part NO. Number Description QuanFigure B See FigureKEY Part Number Craftsman Radial ARM SAW Model no .22038QFigure C Radial ARM SAW Model noCraftsman Radial ARM SAW Model no Parts List for Figure CCraftsman Radial ARM SAW Model no Keypart NO.NUMBER Parts List for Figure ORgure E Craftsman Radial ARM SAW- Model no69CRRFTSMBWRADIALSAW315.220380 Craftsman Radial ARM SAW- Model noCraftsman RADIAL-ARM SAW Model no SeefiguregDescription Parts List for Figure FSee Figure F Figure G73RRFTSMIINRADIALSAW315.220380 Craftsman Radial ARM SAW Model noFigure H KEY Part Number Description Parts List for Figure H11 9 Parts List for Figure Rgure J SeergurekParts List for Figure J Figure K Parts List for Figure K PartsDirect