Craftsman 315.22831 owner manual Hardware for Blade Guard Bracket and Blade Guard Assembly

Page 12

Check all loose parts from the box with the list and figures below and on the previouspages, Small items such as fasteners and end caps are shown in figure 2 c. Follow the instructionsin the Assembly sectionto assemble your new saw.

O. Hardware for Rail, Front	1
square head bolt (5/16-18 x 1 in..)	6
flat washer (5/16 in.)	6
hex nut (5/16-18)	6
end cap for front rail	2
screw (5/32-32 x 1/2 in.)	2

Y.Hardware for Blade Guard Bracket and Blade

Guard Assembly

Blade Guard Bracket	1
hex cap screw (5/16-18 x 1/2 in.)	2
lock washer (5/16 in.)	2

©

F, Hardware For Rail, Rear	1
square head bolt (5/16-18 x 1 in.)	6
flat washer (5/16 in.)	6
hex nut (5/16-18)	6
end cap for rear rail	2
screw (5/32-32 x 1/2 in.)	2

Blade Guard Assembly	1
socket head cap screw (1/4-20 x 3/8 in.)	3
flat washer (1/4 in.) ..._	3

Fig. 2 c

CRAFTSMAN"TABLESAW315.22831012

Image 12

Contents Table SAW NRTL/CFulloneyearwarrantyoncraftsmantablesaw CRAFTSMANTABLESAW315.22831028-32 Safety Alert Symbol Read ALL Instructions5CRAFTSMANTABLESAW315,228310 Before Changing the SETUP, Removing Inspect Tool Cords and ExtensionSpeed and Wiring Extension CordsElectrical Connection Grounding InstructionsRRRFTSNlUI TABLESAW$1G,228310 Bit MoldingHead Set Blade Guard Bracket SwitchAssembly Hardware for Leveling Feet Hardware for Blade Guard Bracket and Blade Guard Assembly Framingsquareadjustablewrench Small I Medium Nutdriver PhilupsscrewdriverHexkeysprovided Combinaonsouare Hammer 45TRIANGLEInch Table Saw Pushoff 15IRRFTSMIINTABLESAW315.228310Extension Erview See Figure See Figures 7HEXI,LEGSTAND Mounting the LEG Stand on the Table SAW BaseAssembling Table Extensions Aligning Table ExtensionsFLA Washer Henut Installing the Rear Rail See Figures 12Installing the Front Rail Rhtbcale Switch Withkey ExtensionSee Figures 15 Souare Headbolts Extension FrontrailMotor Bracketmotor Assembly Washer AligningtheripfenceandfrontrailSee Figures 17and Installingthebeltandbeltguard See Figures20Sawpulley Belt Belti Checking the Throat PlateInstalling the Blade Guard Socket See Figures 23Headscrews PawlsAligningtherivingknifewiththe Blade See Figures26Checking RIP Fence and Blade Mitergage Ripfence Alignment See Figures 29Blade Grooveframing Souare Ripfence Mitergage Groove Bladeframing SquareReplacing the Blade See Figures 32Blade Guard Arborshaft Blade Washer BladehutSee Figures 35 Framing Square Mitergagegroove90STOPSCREW 45STOPSCREW Hexkey CRAFTSMAN*TABLESAW315.22831030Adjustable Stopscrew Locknut Stoppin Removing / Replacing the Throat Plate Throatplate Keyslot SpringclipBasic Operation of the Table SAW Causes of KickbackAvoiding Kickback Cutting AidsTypes of Cuts See Figure There are six basic cuts t the cross cutMaking a Cross CUT WhenmitergageisMaking a RIP CUT OnleftsideofbladeMakinga Mitercut Making a Bevel Cross CUTSee Figures47 Mitercut Bevel LockhandleMakinga Bevelripcut BevelripcutMaking a Compound Bevel Miter CUT Sea FigureMaking a Large Panel CUT Making a NON-THROUGH CUTLargepanelcut NonhroughcutMaking a Dado CUT General Maintenance Motor / ElectricalProblem CausesolutionProblem Cause Solution See Hee/ingtheSawbladeinthe AdjustmentssectionProblem SolutionFront Rail in the Assembly section CauseCrrftsman Table SAW Figure a Parts List for Figure a Craftsman Table SAW Model noKEY Part NO.NUMBER Description QuanFigureb Parts List for Figure B Craftsmantable SAW MODELNO.315.228310KEY Part Number Description Quan 2517 Parts List for Figure C KEY Part NO. NumberKEY Part NO. Number Description Quan Figured Parts List for Figure D Figuree Parts List for Figure E Figuref Parts List for Figure F Is,wem0eworoe0on e 0enumcFigureg Parts List for Figure G Craftsmantable SAW- ModelnoCraftsman Table SAW- Model no FigurehParts List for Figure H KEYPart Number 4038 Parts List for Figure