Craftsman 315.22831 owner manual Problem, Cause, Solution, Front Rail in the Assembly section

Page 44

PROBLEM

Rip fence does not move smoothly.

Wood edges away from rip fence when ripping.

CAUSE

1.Rip fence is not mounted cor- rectly.

2.Rails are dirty or sticky.

1.Rip fence is misaligned.

SOLUTION

1.Remove and repositionthe rip fence. See Aligning Rip Fence

and Front Rail in the Assembly section.

2.Clean and wax the mils.

1.See the Assembly section for Checking Rip Fence and Blade

Alignmentand Aligning Rip Fence and Front Rail

procedures.

CRIIFTSMlU4"TABLESAW3_G.22834,044

Image 44

Contents Table SAW NRTL/CFulloneyearwarrantyoncraftsmantablesaw CRAFTSMANTABLESAW315.22831028-32 Safety Alert Symbol Read ALL Instructions5CRAFTSMANTABLESAW315,228310 Before Changing the SETUP, Removing Inspect Tool Cords and ExtensionSpeed and Wiring Extension CordsElectrical Connection Grounding InstructionsRRRFTSNlUI TABLESAW$1G,228310 Bit MoldingHead Set Blade Guard Bracket SwitchAssembly Hardware for Leveling Feet Hardware for Blade Guard Bracket and Blade Guard Assembly Framingsquareadjustablewrench Small I Medium Nutdriver PhilupsscrewdriverHexkeysprovided Combinaonsouare Hammer 45TRIANGLEInch Table Saw Pushoff 15IRRFTSMIINTABLESAW315.228310Extension Erview See Figure See Figures 7HEXI,LEGSTAND Mounting the LEG Stand on the Table SAW BaseFLA Washer Henut Assembling Table ExtensionsAligning Table Extensions Installing the Rear Rail See Figures 12Installing the Front Rail Rhtbcale Switch Withkey ExtensionSee Figures 15 Souare Headbolts Extension FrontrailSee Figures 17and Motor Bracketmotor Assembly WasherAligningtheripfenceandfrontrail Installingthebeltandbeltguard See Figures20Sawpulley Belt Belti Checking the Throat PlateInstalling the Blade Guard Socket See Figures 23Headscrews PawlsAligningtherivingknifewiththe Blade See Figures26Checking RIP Fence and Blade Mitergage Ripfence Alignment See Figures 29Blade Grooveframing Souare Ripfence Mitergage Groove Bladeframing SquareReplacing the Blade See Figures 32Blade Guard Arborshaft Blade Washer BladehutSee Figures 35 Framing Square Mitergagegroove90STOPSCREW 45STOPSCREW Hexkey CRAFTSMAN*TABLESAW315.22831030Adjustable Stopscrew Locknut Stoppin Removing / Replacing the Throat Plate Throatplate Keyslot SpringclipBasic Operation of the Table SAW Causes of KickbackAvoiding Kickback Cutting AidsTypes of Cuts See Figure There are six basic cuts t the cross cutMaking a Cross CUT WhenmitergageisMaking a RIP CUT OnleftsideofbladeMakinga Mitercut Making a Bevel Cross CUTSee Figures47 Mitercut Bevel LockhandleMakinga Bevelripcut BevelripcutMaking a Compound Bevel Miter CUT Sea FigureMaking a Large Panel CUT Making a NON-THROUGH CUTLargepanelcut NonhroughcutMaking a Dado CUT General Maintenance Motor / ElectricalProblem CausesolutionProblem Cause Solution See Hee/ingtheSawbladeinthe AdjustmentssectionProblem SolutionFront Rail in the Assembly section CauseCrrftsman Table SAW Figure a Parts List for Figure a Craftsman Table SAW Model noKEY Part NO.NUMBER Description QuanFigureb KEY Part Number Description Quan Parts List for Figure BCraftsmantable SAW MODELNO.315.228310 2517 KEY Part NO. Number Description Quan Parts List for Figure CKEY Part NO. Number Figured Parts List for Figure D Figuree Parts List for Figure E Figuref Parts List for Figure F Is,wem0eworoe0on e 0enumcFigureg Parts List for Figure G Craftsmantable SAW- ModelnoCraftsman Table SAW- Model no FigurehPart Number Parts List for Figure HKEY 4038 Parts List for Figure