Craftsman 315.22831 owner manual Problem, Causesolution

Page 42

PROBLEM

Sawdoesnotstart.

CAUSESOLUTION

1.Motorcordorwallcordisnot 1. Pluginmotorcordorwallcord. pluggedin.

2.	Circuitfuseisblown.	2.	Replace circuitfuse.
3.	Cimuitbreakeristripped.	3.	Reset circuit breaker.
4.	Cordorswitchisdamaged.	4.	Have the cord or switch re-
			placed at your nearest Sears
			Service Center.

Sawisnoisywhenrunning.

Motorissloworweak.

Motoroverheats.

Motorstalls,blowsfuses,ortrips

circuitbreakers.

1.Motor needs attention.

1.Voltage from source is low.

2.Windings are burnedout or open.

3.Start switchis defective.

4.Circuit is overloaded with appliances, lights, or other motorS.

1.Motor is overloaded.

2.Du$$blade.

3.Sawdust inside saw is blocking air flow.

1.Starter switch is defective.

2.Voltage from source is low.

3.Dull blade.

4.Fuses or circuit breakers are wrong size or defective.

5, Feeding workplace too rapidly,

1.Have the motor checked at your nearest Sears Service Center.

1.Request a voltage check from the power company.

2, Have the motor checked at

your nearest Sears Service Center.

3, Have the switch replaced.

4.Do not use other appliances or motors on the same circuit

when using the saw.

1.Request a voltage check from the power company.

2.Replace the blade.

3.Clean out the saw base.

1.Have the switch replaced.

2.Request a voltage check from the power company.

3.Replace the blade.

4.Replace fuses or circuit breakers.

5.Feed work,piece into blade slower.

CRIIFTSNRN"TABLESAW315.22831042

Image 42

Contents Table SAW NRTL/CFulloneyearwarrantyoncraftsmantablesaw CRAFTSMANTABLESAW315.22831028-32 Safety Alert Symbol Read ALL Instructions5CRAFTSMANTABLESAW315,228310 Before Changing the SETUP, Removing Inspect Tool Cords and ExtensionElectrical Connection Speed and WiringExtension Cords Grounding InstructionsRRRFTSNlUI TABLESAW$1G,228310 Bit MoldingHead Set Blade Guard Bracket SwitchAssembly Hardware for Leveling Feet Hardware for Blade Guard Bracket and Blade Guard Assembly Hexkeysprovided FramingsquareadjustablewrenchSmall I Medium Nutdriver Philupsscrewdriver Combinaonsouare Hammer 45TRIANGLEInch Table Saw Pushoff 15IRRFTSMIINTABLESAW315.228310Extension Erview See Figure See Figures 7HEXI,LEGSTAND Mounting the LEG Stand on the Table SAW BaseAssembling Table Extensions Aligning Table ExtensionsFLA Washer Henut Installing the Rear Rail See Figures 12See Figures 15 Installing the Front RailRhtbcale Switch Withkey Extension Souare Headbolts Extension FrontrailMotor Bracketmotor Assembly Washer AligningtheripfenceandfrontrailSee Figures 17and Sawpulley InstallingthebeltandbeltguardSee Figures20 Belt Belti Checking the Throat PlateHeadscrews Installing the Blade Guard SocketSee Figures 23 PawlsAligningtherivingknifewiththe Blade See Figures26Blade Grooveframing Souare Checking RIP Fence and Blade Mitergage Ripfence AlignmentSee Figures 29 Ripfence Mitergage Groove Bladeframing SquareBlade Guard Replacing the BladeSee Figures 32 Arborshaft Blade Washer BladehutSee Figures 35 Framing Square Mitergagegroove90STOPSCREW 45STOPSCREW Hexkey CRAFTSMAN*TABLESAW315.22831030Adjustable Stopscrew Locknut Stoppin Removing / Replacing the Throat Plate Throatplate Keyslot SpringclipAvoiding Kickback Basic Operation of the Table SAWCauses of Kickback Cutting AidsTypes of Cuts See Figure There are six basic cuts t the cross cutMaking a RIP CUT Making a Cross CUTWhenmitergageis OnleftsideofbladeSee Figures47 Makinga MitercutMaking a Bevel Cross CUT Mitercut Bevel LockhandleMakinga Bevelripcut BevelripcutMaking a Compound Bevel Miter CUT Sea FigureLargepanelcut Making a Large Panel CUTMaking a NON-THROUGH CUT NonhroughcutMaking a Dado CUT General Maintenance Motor / ElectricalProblem CausesolutionProblem Cause Solution See Hee/ingtheSawbladeinthe AdjustmentssectionFront Rail in the Assembly section ProblemSolution CauseCrrftsman Table SAW Figure a KEY Part NO.NUMBER Parts List for Figure aCraftsman Table SAW Model no Description QuanFigureb Parts List for Figure B Craftsmantable SAW MODELNO.315.228310KEY Part Number Description Quan 2517 Parts List for Figure C KEY Part NO. NumberKEY Part NO. Number Description Quan Figured Parts List for Figure D Figuree Parts List for Figure E Figuref Parts List for Figure F Is,wem0eworoe0on e 0enumcFigureg Parts List for Figure G Craftsmantable SAW- ModelnoCraftsman Table SAW- Model no FigurehParts List for Figure H KEYPart Number 4038 Parts List for Figure