Craftsman 315.22831 owner manual See Figure, Adjustable Stopscrew Locknut Stoppin

Page 31

•Check the 45" setting. Tilt the blade with the bevel handwheel as far as it will go to the left. Place the square against the blade (be sure the square is not against one of the saw teeth). Ifthe blade is not at

45", unscrewthe 45" stop screw (right of blade), turnthe handwheel untilthe blade is correct, and

tighten the screw. Recheck and repeat if neces- sary.

•Check that the scale indicatoris at 45°.

•If not, loosen the scale indicatorwith a screwdriver, adjust it withinthe slot,and retightenthe screw.

•Loosen knob and pull out on stop pin to rotate miter gage base past stop screws.

•Loosen the lock nut of the 0" stop screw at the stop pin with a 8 mm wrench.

•Place a 90" square against the miter gage rod and the miter gage base.

•If the rod is not square, loosen the knob, adjust the rod, and tighten the knob.

•Adjustthe 0" stop screw until it rests against the stop pin.

•Adjustthe plus and minus45" stop screws using a 45" tdangle and the steps above.

MITERKNOB

GAGEROD MITER

GAGEBASE

SCALE

INDICATOR	Fig. 39
	Fig. 39
ADJUSTING THE MITER GAGE		STOPSCREW
ADJUSTING THE MITER GAGE
See Figure 40.
You can set the miter gage at O"and plus or minus45"
with the miter gage stop pin and adjustable stop
screws
Note: The miter gage providesclose accuracy in
angled cuts. For very cloSe tolerances, test
cuts are recommended.

0° ADJUSTABLE STOPSCREW

LOCKNUT

STOPPIN

Fig. 40

31	rRRFTSMRN" TABLESAW315.228310

Image 31

Contents NRTL/C Table SAWCRAFTSMANTABLESAW315.228310 Fulloneyearwarrantyoncraftsmantablesaw28-32 Read ALL Instructions Safety Alert Symbol5CRAFTSMANTABLESAW315,228310 Inspect Tool Cords and Extension Before Changing the SETUP, RemovingGrounding Instructions Speed and WiringExtension Cords Electrical ConnectionRRRFTSNlUI TABLESAW$1G,228310 Bit MoldingHead Set Blade Guard Bracket SwitchAssembly Hardware for Leveling Feet Hardware for Blade Guard Bracket and Blade Guard Assembly Combinaonsouare Hammer 45TRIANGLE FramingsquareadjustablewrenchSmall I Medium Nutdriver Philupsscrewdriver HexkeysprovidedInch Table Saw 15IRRFTSMIINTABLESAW315.228310 PushoffExtension Erview See Figures 7 See FigureMounting the LEG Stand on the Table SAW Base HEXI,LEGSTANDAligning Table Extensions Assembling Table ExtensionsFLA Washer Henut See Figures 12 Installing the Rear RailSouare Headbolts Extension Frontrail Installing the Front RailRhtbcale Switch Withkey Extension See Figures 15Aligningtheripfenceandfrontrail Motor Bracketmotor Assembly WasherSee Figures 17and Belt Belti Checking the Throat Plate InstallingthebeltandbeltguardSee Figures20 SawpulleyPawls Installing the Blade Guard SocketSee Figures 23 HeadscrewsSee Figures26 Aligningtherivingknifewiththe BladeRipfence Mitergage Groove Bladeframing Square Checking RIP Fence and Blade Mitergage Ripfence AlignmentSee Figures 29 Blade Grooveframing SouareArborshaft Blade Washer Bladehut Replacing the BladeSee Figures 32 Blade GuardFraming Square Mitergagegroove See Figures 35CRAFTSMAN*TABLESAW315.22831030 90STOPSCREW 45STOPSCREW HexkeyAdjustable Stopscrew Locknut Stoppin Throatplate Keyslot Springclip Removing / Replacing the Throat PlateCutting Aids Basic Operation of the Table SAWCauses of Kickback Avoiding KickbackSee Figure There are six basic cuts t the cross cut Types of CutsOnleftsideofblade Making a Cross CUTWhenmitergageis Making a RIP CUTMitercut Bevel Lockhandle Makinga MitercutMaking a Bevel Cross CUT See Figures47Bevelripcut Makinga BevelripcutSea Figure Making a Compound Bevel Miter CUTNonhroughcut Making a Large Panel CUTMaking a NON-THROUGH CUT LargepanelcutMaking a Dado CUT Motor / Electrical General MaintenanceCausesolution ProblemSee Hee/ingtheSawbladeinthe Adjustmentssection Problem Cause SolutionCause ProblemSolution Front Rail in the Assembly sectionCrrftsman Table SAW Figure a Description Quan Parts List for Figure aCraftsman Table SAW Model no KEY Part NO.NUMBERFigureb Craftsmantable SAW MODELNO.315.228310 Parts List for Figure BKEY Part Number Description Quan 2517 KEY Part NO. Number Parts List for Figure CKEY Part NO. Number Description Quan Figured Parts List for Figure D Figuree Parts List for Figure E Figuref Is,wem0eworoe0on e 0enumc Parts List for Figure FFigureg Craftsmantable SAW- Modelno Parts List for Figure GFigureh Craftsman Table SAW- Model noKEY Parts List for Figure HPart Number 4038 Parts List for Figure