Craftsman 315.22831 owner manual Hexi,Legstand, Mounting the LEG Stand on the Table SAW Base

Page 19

ASSEMBLINGLEGSTAND(Continued)

•Align the two large holes on the brace and the legs.

Insert the cardage bolts. Add flat washers and hex nuts and hand tighten. Repeat for the other short upper brace. These are the front and back sets.

•For the sides, install a long upper brace on two legs. Add hardware and finger tighten. Repeat for the other long upper brace.

•Use the same steps to installthe lower braces. Tighten all hex nutswith a 12 mm wrench.

•Place a hex nut and flat washer on each leveling foot. install the levelingfeet from the bottomof each leg with the boltspointingup. Secure with a fiat washer and hex nut but do not tighten.

•Move the leg stand to desired location. Adjustthe leveling feet with a 12 mm wrench, then securely tighten the top hex nut.

_k WARNING: Do not lift the saw table without help. The table saw base weighs approximately

95Ibs. Hold it close to your body. Keep your knees bent and liftwith your legs, not your back. Ignoringthese precautionscan result in back injury.

•Place the leg stand on the table saw base. Align the holes in the table with the holes in the end

braces. Make sure the Craftsman label faces the front of the saw (same side as height handwheel).

•Place a flat washer on each bolt and insertthrough hole. Add a flat washer and a hex nut. Hand

tighten.

•Repeat for the three remainingholes. Tighten all

hardware with a 12 mm wrench. You may find it helpfulto use two wrenches, one wrench to hold

the head of the boltand one to tightenthe hex nut.

Leave the saw upside downto add table exten- sions.

HEXI,LEGSTAND

LEGSTANDSHOWNASSEMBLED Fig. 8

MOUNTING THE LEG STAND ON THE TABLE

SAW BASE

See Figure 9.

•Take the followingfrom the hardware bag:

4 hex bolts(5/16-18 x 1/2 in.)

4 hex nuts (5/18-18)

8 flat washers (5/16 in.)

Note: This hardware was in the bag with hardware for assemblingthe leg stand and levelingfeet.

•Place the saw table upside down on a smooth surface, such as cardboard, on the floor.

Fig. 9

19CRAFTSMRN"TABLESAW315.228310

Image 19

Contents NRTL/C Table SAWCRAFTSMANTABLESAW315.228310 Fulloneyearwarrantyoncraftsmantablesaw28-32 Read ALL Instructions Safety Alert Symbol5CRAFTSMANTABLESAW315,228310 Inspect Tool Cords and Extension Before Changing the SETUP, RemovingGrounding Instructions Speed and WiringExtension Cords Electrical ConnectionRRRFTSNlUI TABLESAW$1G,228310 Bit MoldingHead Set Blade Guard Bracket SwitchAssembly Hardware for Leveling Feet Hardware for Blade Guard Bracket and Blade Guard Assembly Combinaonsouare Hammer 45TRIANGLE FramingsquareadjustablewrenchSmall I Medium Nutdriver Philupsscrewdriver HexkeysprovidedInch Table Saw 15IRRFTSMIINTABLESAW315.228310 PushoffExtension Erview See Figures 7 See FigureMounting the LEG Stand on the Table SAW Base HEXI,LEGSTANDAligning Table Extensions Assembling Table ExtensionsFLA Washer Henut See Figures 12 Installing the Rear RailSouare Headbolts Extension Frontrail Installing the Front RailRhtbcale Switch Withkey Extension See Figures 15Aligningtheripfenceandfrontrail Motor Bracketmotor Assembly WasherSee Figures 17and Belt Belti Checking the Throat Plate InstallingthebeltandbeltguardSee Figures20 SawpulleyPawls Installing the Blade Guard SocketSee Figures 23 HeadscrewsSee Figures26 Aligningtherivingknifewiththe BladeRipfence Mitergage Groove Bladeframing Square Checking RIP Fence and Blade Mitergage Ripfence AlignmentSee Figures 29 Blade Grooveframing SouareArborshaft Blade Washer Bladehut Replacing the BladeSee Figures 32 Blade GuardFraming Square Mitergagegroove See Figures 35CRAFTSMAN*TABLESAW315.22831030 90STOPSCREW 45STOPSCREW HexkeyAdjustable Stopscrew Locknut Stoppin Throatplate Keyslot Springclip Removing / Replacing the Throat PlateCutting Aids Basic Operation of the Table SAWCauses of Kickback Avoiding KickbackSee Figure There are six basic cuts t the cross cut Types of CutsOnleftsideofblade Making a Cross CUTWhenmitergageis Making a RIP CUTMitercut Bevel Lockhandle Makinga MitercutMaking a Bevel Cross CUT See Figures47Bevelripcut Makinga BevelripcutSea Figure Making a Compound Bevel Miter CUTNonhroughcut Making a Large Panel CUTMaking a NON-THROUGH CUT LargepanelcutMaking a Dado CUT Motor / Electrical General MaintenanceCausesolution ProblemSee Hee/ingtheSawbladeinthe Adjustmentssection Problem Cause SolutionCause ProblemSolution Front Rail in the Assembly sectionCrrftsman Table SAW Figure a Description Quan Parts List for Figure aCraftsman Table SAW Model no KEY Part NO.NUMBERFigureb Craftsmantable SAW MODELNO.315.228310 Parts List for Figure BKEY Part Number Description Quan 2517 KEY Part NO. Number Parts List for Figure CKEY Part NO. Number Description Quan Figured Parts List for Figure D Figuree Parts List for Figure E Figuref Is,wem0eworoe0on e 0enumc Parts List for Figure FFigureg Craftsmantable SAW- Modelno Parts List for Figure GFigureh Craftsman Table SAW- Model noKEY Parts List for Figure HPart Number 4038 Parts List for Figure