Craftsman 315.22831 owner manual Bit MoldingHead Set

Page 9

Your new table saw has been designed to give you many years of high quality performance. To insure this goal, proper care and treatment is important.

Careful treatment begins with removing all pads from the cartonand checking them against the list of loose parts.The long box contains the rails. The large box holdsall other parts, which are detailed in the Loose

Parts List.

•Separate the saw and all parts from the packing materials and check each against the packing list, especially the small parts that can be hidden in the packing material

Note: Do not discard the packing materials until you have carefully inspected the saw, identified all parts, and satisfactorily operated your new saw.

_IL WARNING: Never use gasoline, naptha, or other highlyvolatile solvents. Do not ever let brake fluids, gasoline, petroleum-based

products,or penetrating oilscontact plasticparts. Such chemicals can weaken or destroy plastic.

IIRemove the wax paper covering on the table. Use any ordinary household type grease and spot remover. Immediately apply a coat of automotive type paste wax to the table and table exensions.

,_ WARNING: To prevent accidental startingthat could cause possibleserious personal injury, assemble all parts to your saw before connecting it to power supply.Saw should never be connected to power supplywhen you are assembling parts, making adjustments, installing or removingblades, or when not in use.

,_ WARNING: If any parts are missing,do not operate this tool untilthe missing parts are

replaced. Failure to do so could result in possible serious personal injury.

The following recommended accessoriesare currentlyavailable at Sears Retail Stores.

•

Fence Guide System

• 7 in. Stack Steel Dado

 

 

•

Guide Master

• 7 in. x 9/16 in. Stack Dado

 

 

•

Box Joint & Miter Guide

• 7 in. MoldingHead Set

 

 

•

Universal Jig

• 2 Bit MoldingHead Set

 

 

•

Taper Jig

•

Saw Baskets

• 10 in. Sanding Disc

•

Jointer Clamps

 

 

•

8 in. Sanding Disc

•

Specialty Throat Plate

•

Elite Dado

• Miter Gage Hold Down Clamp

•

ExcaliburDado

• Align-A-RipXRC Rip Fence

 

 

•

7 in. Adj. Dado 36 tip

•

Dust CollectionSystem

 

 

•7 in. Adj. Dado 24 tip

,_ WARNING: The use of attachments or accessories not listed might be hazardous.

9

[RAFTSMAN" TABLESAW315.228310

Page 8 Page 10
Image 9
Page 8 Page 10
Contents NRTL/C Table SAWCRAFTSMANTABLESAW315.228310 Fulloneyearwarrantyoncraftsmantablesaw28-32 Read ALL Instructions Safety Alert Symbol5CRAFTSMANTABLESAW315,228310 Inspect Tool Cords and Extension Before Changing the SETUP, RemovingExtension Cords Speed and WiringElectrical Connection Grounding InstructionsRRRFTSNlUI TABLESAW$1G,228310 Bit MoldingHead Set Blade Guard Bracket SwitchAssembly Hardware for Leveling Feet Hardware for Blade Guard Bracket and Blade Guard Assembly Small I Medium Nutdriver Philupsscrewdriver FramingsquareadjustablewrenchHexkeysprovided Combinaonsouare Hammer 45TRIANGLEInch Table Saw 15IRRFTSMIINTABLESAW315.228310 PushoffExtension Erview See Figures 7 See FigureMounting the LEG Stand on the Table SAW Base HEXI,LEGSTANDAssembling Table Extensions Aligning Table ExtensionsFLA Washer Henut See Figures 12 Installing the Rear RailRhtbcale Switch Withkey Extension Installing the Front RailSee Figures 15 Souare Headbolts Extension FrontrailMotor Bracketmotor Assembly Washer AligningtheripfenceandfrontrailSee Figures 17and See Figures20 InstallingthebeltandbeltguardSawpulley Belt Belti Checking the Throat PlateSee Figures 23 Installing the Blade Guard SocketHeadscrews PawlsSee Figures26 Aligningtherivingknifewiththe BladeSee Figures 29 Checking RIP Fence and Blade Mitergage Ripfence AlignmentBlade Grooveframing Souare Ripfence Mitergage Groove Bladeframing SquareSee Figures 32 Replacing the BladeBlade Guard Arborshaft Blade Washer BladehutFraming Square Mitergagegroove See Figures 35CRAFTSMAN*TABLESAW315.22831030 90STOPSCREW 45STOPSCREW HexkeyAdjustable Stopscrew Locknut Stoppin Throatplate Keyslot Springclip Removing / Replacing the Throat PlateCauses of Kickback Basic Operation of the Table SAWAvoiding Kickback Cutting AidsSee Figure There are six basic cuts t the cross cut Types of CutsWhenmitergageis Making a Cross CUTMaking a RIP CUT OnleftsideofbladeMaking a Bevel Cross CUT Makinga MitercutSee Figures47 Mitercut Bevel LockhandleBevelripcut Makinga BevelripcutSea Figure Making a Compound Bevel Miter CUTMaking a NON-THROUGH CUT Making a Large Panel CUTLargepanelcut NonhroughcutMaking a Dado CUT Motor / Electrical General MaintenanceCausesolution ProblemSee Hee/ingtheSawbladeinthe Adjustmentssection Problem Cause SolutionSolution ProblemFront Rail in the Assembly section CauseCrrftsman Table SAW Figure a Craftsman Table SAW Model no Parts List for Figure aKEY Part NO.NUMBER Description QuanFigureb Parts List for Figure B Craftsmantable SAW MODELNO.315.228310KEY Part Number Description Quan 2517 Parts List for Figure C KEY Part NO. NumberKEY Part NO. Number Description Quan Figured Parts List for Figure D Figuree Parts List for Figure E Figuref Is,wem0eworoe0on e 0enumc Parts List for Figure FFigureg Craftsmantable SAW- Modelno Parts List for Figure GFigureh Craftsman Table SAW- Model noParts List for Figure H KEYPart Number 4038 Parts List for Figure
Top Page Image Contents