Graco 3A2587H important safety instructions Hand-Held Sprayer Model 16N658 Metric

Page 29

Technical Data

Hand-Held Sprayer (Model: 16N658)

 

U.S.

Metric

 

 

 

Fixed Pressure

1300 psi

9.9 MPa, 89.6 bar

 

 

 

Maximum Amperage

4 Amps

4 Amps

 

 

 

Weight

6.86 lb (15 ft cord)

3.11 kg (4.6 m cord)

 

 

 

Dimensions:

 

 

 

 

 

Length

12.75 in.

32.4 cm

 

 

 

Width

5.5 in.

14.0 cm

 

 

 

Height

10.75 in.

27.3 cm

 

 

 

Storage Temperature Range 

32° to 113° F

0° to 45° C

 

 

 

Operating Temperature Range

40° to 90° F

4° to 32° C

 

 

 

Storage Humidity Range

0% to 95% relative humidity,

0% to 95% relative humidity,

 

non-condensing

non-condensing

 

 

 

Sound Pressure Level

70.5 dBa† (for sound power level, add 81.5 dBa)

 

 

 

Vibration Level Acceleration

Less than 2.2 feet/s2

Less than 0.67 m/s2††

Power Cord

18 AWG, 3-wire, 15 ft

1.0 mm2, 3-wire, 4.6 m

Electrical Power Requirement

120 Vac, 60 Hz, 15A, 1 phase

 

 

 

 

Pump damage will occur if fluid freezes in pump.

Damage to plastic parts may result if impact occurs in low temperature conditions.

Changes in paint viscosity at very low or very high temperatures can affect sprayer performance.

† per ISO 3744 measured at 3.3 feet (1m) †† per ISO 5349, no load condition

3A2587H

29

Image 29
Contents Model Voltage Description Adjustable Pressure Fixed PressureTable of Contents Extension Cord Gauge Extension Cord Length AWG Minimum GroundingExtension Cords Skin Injection Hazard Fire and Explosion HazardElectric Shock Hazard Pressurized Aluminum Parts Hazard Equipment Misuse HazardMoving Parts Hazard Toxic Fluid or Fumes HazardComponent Identification Power Cord Using Electrical CordsGrounding and Electrical Requirements Extension Cord RequirementsTrigger Lock Pressure Relief ProcedurePrime/Spray Valve Trigger LockedPressure Control Knob Reversible Spray TipFlexible Suction Tube Not available on all unitsOverheating Protection Sprayer SetupIf sprayer fails to prime, try one of the steps below Starting a New Job Or Refilling the Material CupChoosing the Correct Tip Choosing Pressure Control Knob SettingUnderstanding Tip Number Selecting Tip Hole SizeTriggering Sprayer Install Spray Tip/Guard Assembly if not installedGetting Started with Basic Techniques Spray Pattern Quality Unclogging Spray Tip/Guard AssemblyAiming Sprayer Flushing Sprayer Shutdown and CleaningTi15529ati18926a Storage Cleaning Sprayer ExteriorModels 16N658, 16N659, 16N673, 17C810 Replacement PartsDescription Parts List Models 16N658, 16N659, 16N673, 17C810Model 16N659, 16N673, 17C810 16M873 Installation Inlet Valve Fitting Removal/ServiceRemoval Outlet Valve Fitting RepairWiring General ServiceProblem Cause Solution TroubleshootingMaterial Spray Pattern DiagnosticsSee Shutdown and Cleaning, Problem Cause Solution Troubleshooting LeaksHand-Held Sprayer Models 16N673, 16N659 Metric Technical DataHand-Held Sprayer Model 16N658 Metric Date Material Spray Pressure Setting Preferred Material Settings LogExample Mark Dial3A2587H Graco Information Graco Standard Warranty