Graco Inc 313516C important safety instructions Install Air Fittings, Ground System

Page 11

Install Air Fittings

1.Install the supplied 1/4 in. tube fitting into the cylinder (CYL) air port.

2.Install 3/8 in. tube fittings into the atomiza- tion (ATOM) air port and the fan (FAN) air port.

CYL

ATOM

FAN

ti8211a

FIG. 2: Air Fittings

Installation

Ground Air Compressors and Hydraulic Power Supplies

Ground the air compressors and hydraulic power supplies according to the manufacturer recommendations.

Ground Spray Gun

Ground the spray gun by mounting the mani- fold to a properly grounded reciprocator, robot, or stationary mount. Check the electrical resis- tance between the manifold and a true earth ground. The resistance must be less than 1 megohm.

Ground Fluid Supply Container

Ground the fluid supply container according to local code.

Ground Object Being Sprayed

Ground the object that is being sprayed according to local code.

Ground System

The following grounding instructions are mini- mum requirements for a system. Your system may include other equipment or objects that must be grounded. Check your local electrical code for detailed grounding instructions for your area and type of equipment. Your system must be connected to a true earth ground.

Ground Pump/Fluid Supply

Ground the pump by connecting a ground wire and clamp between the fluid supply and a true earth ground as instructed in your separate pump instruction manual.

Ground Solvent Pails

Ground all solvent pails that are used when flushing according to local code. Use only metal pails, which are conductive. Do not place the pail on a non-conductive surface, such as paper or cardboard, which interrupts the grounding continuity.

313516C

11

Image 11

Contents Automatic AirPro Spray Guns Important Safety InstructionsModels ContentsFire and Explosion Hazard Pressurized Equipment Hazard General Metal Applications Selection ChartsHvlp Guns High Wear ApplicationsWood Applications Gun SelectionConventional Guns Proper Needle/Nozzle SelectionAir Caps Air Flow Air FlowAtomizing Air Fan Air Maximum HVLP/Compliant inlet manifold pressure Circulating System InstallationVentilate Spray Booth Configure Gun and ManifoldGround System Install Air FittingsStationary Support Mount GunReciprocating Arm Rod Mount Retrofit Adapter Plate Mount Retrofit Adapter PlateConnect Fluid Hose SetupConnect Air Line Position Air Cap Flush Spray GunSpray Gun Adjust Spray PatternSuggested Starting Settings Atomization Fan Air psiAir Pressure Regulator Incorrect Pressure Relief ProcedureOperation Apply FluidDaily Gun Care Clean and Flush Gun General System MaintenanceProblem Cause Solution TroubleshootingGeneral Troubleshooting Spray Pattern Troubleshooting Disassembly ServiceAlternate Fluid Control Shown Reassembly 17† 21† Alternate Fluid Control 20† 22† 36† 24a 25a PartsGasket Nozzle Repair KitsGeneral Metal Applications Wood Applications High Wear ApplicationsPart Description Qty Manifold with bottom fluid portsPart No C342 Side Fluid Ports and Fan Adjustment ValveNot shown, optional size Not sold separately Part No only Description Qty106 Accessories Count Carton Pack Description Hvlp Pressure Verification KitInline Fluid Filter 24B707 Spray Tip FiltersManifold Model 288221, All Gun Models DimensionsManifold Models 288217 or 288218, All Gun Models Manifold Model 288160 or 288211, All Gun Models Manifold Model 288223 or 24C342, All Gun ModelsMounting Hole Layouts 23.4 mm 10.2 mm 53.3 mm 50 in .7 mm Mounting hole 216 23.4 mm 10.2 mm 27.9 mm 375 in .5 mm Mounting hole Retrofit Adapter Plate Cylinder Air Fluid Pressure Air Pressure Msec to fully Technical DataTriggering Speed Sound DataGraco Headquarters Minneapolis Graco Standard WarrantyGraco Information